Deutsch In-Car Audio Visual Navigation English MODEL INSTALLATION MANUAL Français Contents Connections 2 For your safety in using the AVN4429 3 Names and functions of terminals 5 Connecting the vehicle speed pulse, parking brake, and reverse cables (wires) 8 System connection example 10 Installing the GPS antenna 11 Installing the main unit 13 Checking operation after installation 15 Nederlands Installation Components Italiano Before installation Español Be sure to read this ins
Deutsch Components Check that all of the following components are present Main unit components English 1 Main unit x 1 2 Interconnecting cable 3 Interconnecting cable (Power and speaker connector) (16P) x 1 5 Hex-head bolt 6 Flat head screw Español (Red:M5x8) x 4 9 Earth plate 4 Interconnecting cable (Speed pulse, Parking, USB, iPod, etc) (14P) x 1 8 GPS antenna 7 Splicing connector (Red:M5x8) x 8 (Reverse, Back-eye camera, etc) (16P) x 1 x1 x3 10 Cable tie x1 (for GPS antenna) x4
Warnings and caution signs, illustrated bellow, are posted throughout this manual as well as on the AVN4429. They show safe and correct ways to handle the main unit so as to prevent personal injury to you and others and avoid damage to property. Before reading through the manual, take time to read through and learn the important information listed in this section.
Deutsch • For best results, this main unit should be installed by a professional installer. Contact the dealer whom you purchased the main unit for an appointment. • Once installation and wiring have been completed, return the brakes and electrical equipment such as lights, horn, hazard warning lights and turn signal lights to their original places, and check that they operate correctly.
8 1P ANTENNA PLUG 2 16P 14P Español 1 English • Never cut the insulation on the power cable or use it to power any other equipment. If the rated current capacity of the power cable is exceeded, fire and electric shocks may result. • The cables should be secured with tape or a similar securing method to prevent any obstructions while driving. If they get wound or entangled around components such as the steering wheel, shifting lever, or brake pedal, accidents may result.
Deutsch Wire colours and connection points for connection cables 1 2 , 3 and 4 Antenna power supply (Blue) Connect to the automatic-antenna control terminal of the vehicle. 2 Control power supply (Blue/White) Connect the control terminal for the external amplifier, etc. English 3 Not for Use (Pink) Be sure to wrap PVC tape or use a similar cable insulating method. 4 Earth (Black) Connect where good body earthing is available.
• iPod is a registeredtrademark of Apple Inc. in the U.S. and other countries. • "Made for iPod" means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards. • Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Deutsch Connecting the vehicle speed pulse Notes on installation English •Check the vehicle speed pulse signal, parking brake signal, and reverse signal carefully before making the connections. If the cables are incorrectly connected, accidents or problems with correct operation may result. •The label on the vehicle speed pulse signal cable contains a protection circuit, so do not cut the cable or remove the protective circuit, otherwise problems with operation may result.
Tip • Be sure to connect the reverse signal cable. If it is not connected, the vehicle position may be incorrect when the vehicle is reversed. • Use a circuit tester to confirm that a sensing voltage of 6 V or higher is generated when the vehicle is reversed. Use a splicing connector to connect the reverse signal cable (green) coming from the main unit to the reverse signal cable of the vehicle. 2 Route the reverse signal cable to the main unit .
Deutsch System connection example English • Never cut the insulation on the power cable or use it to power any other main unit. If the rated current capacity of the power cable is exceeded, fire and electric shocks may result. • The cables should be secured with tape or a similar securing method to prevent any obstructions while driving. If they get wound or entangled around components such as the steering wheel, shifting lever, or brake pedal, accidents may result.
Notes on installation Tip • If installing the GPS antenna inside the vehicle, be sure it is mounted to the earth plate. • The materials used in front and rear vehicle windows can cause GPS reception sensitivity to drop significantly. If this happens, install the GPS antenna on the outside of the vehicle. • Wipe the installation surface thoroughly so that it is clear of any dirt, moisture, or grease before installing the antenna.
Deutsch 1 Choose an installation location on the dashboard which is flat and has a clear view of the sky. 9 8 Tip English • Select a location that is at least 50 cm. away from the main unit. If this is not done, the GPS measurement precision will drop. • Be sure to use the earth plate when installing the GPS antenna. If the earth plate is not used, the reception sensitivity will drop and will affect the accuracy of the position measurement. 2 Install the earth plate to the dashboard.
1 To maintain proper function, the unit must be mounted less than 30 degrees. If the angle is in excess of 30 degrees, DVD/CD skipping and improper DVD/CD ejection may occur. Deutsch Installing the main unit Front 30˚ or less 2 Remove the carrying bracket. 1 Tip The hexagonal head bolts (Red) which are removed may be used again later when reinstalling.
Deutsch If installing using the 2DIN installation kit (sold separately) Tip Refer to the instructions provided with the kit (sold separately) for details on the installation method. If installing using the existing vehicle bracket and a multi-purpose bracket (such as for Japanese vehicles) 5 Attach the brackets to the main unit. 1 English Tip Be sure to use the supplied accessory mounting screws (Red: M5 x 8) as the mounting screws.
1 Install the PND to the main unit. 11 English 1 2 Deutsch Chec king oper ation after installation Insert the ignition key into the vehicle and start the engine. Tip Check the connection status for each signal in a place where they are easy to see. 4 Use the “GPS signal” gauge which is displayed in the lower-right corner of the map screen to check the reception status. Français 3 Español • Do not turn the ignition key to ACC OFF or operate the main unit until the navigation screen appears.