User Manual

ITEM NAME CATEGORY
1 Spinner1 C
2 Spinner2 C
3 Fus1 A / A-LW
4 Canopy A / A-LW
6 Fus2 A / A-LW
7 Fus3 A / A-LW
8 Fus4 A / A-LW
9 Fus5 A / A-LW
10 VTP A / A-LW
11 Rudder_1 A / A-LW
12 Rudder_2 A / A-LW
13 Wing_C A / A-LW
14 Wing1L A / A-LW
15 Wing1R A / A-LW
16 Wing2L A / A-LW
17 Wing2R A / A-LW
18 Wing3L A / A-LW
19 Wing3R A / A-LW
20 Flaperon_1L A / A-LW
21 Flaperon_1R A / A-LW
22 Flaperon_2L A / A-LW
23 Flaperon_2R A / A-LW
24 Flaperon_3L A / A-LW
25 Flaperon_3R A / A-LW
26 Winglet_1L A / A-LW
27 Winglet_1R A / A-LW
28 Winglet_2L A / A-LW
29 Winglet_2R A / A-LW
30 Wingtip_1L A / A-LW
31 Wingtip_1R A / A-LW
32 HTP1L A / A-LW
33 HTP1R A / A-LW
34 HTP2L A / A-LW
35 HTP2R A / A-LW
36 Elev1L A / A-LW
37 Elev1R A / A-LW
38 Anchor_nut_lower C
39 Anchor_nut_top C
40 Exhaust C / C-LW
41 Tundra tyre C / C-LW
42 Tundra tyre half C / C-LW
43 Tundra_rim C
44 Fitting_rubber C
45 LG_root_front C
46 LG_root_rear C
47 Hinge_rudder C
48 Hinge_wing C
49 Axis_w_hole C
50 Hinge_elev C
51 Motor_holder C
52 Servo_holder_fus C
53 Servo_holder_Wing C
54 LG_fitting C
55 Wheel_fairing_1L C / C-LW
56 Wheel_fairing_1R C / C-LW
57 Wheel_fairing_2L C / C-LW
58 Wheel_fairing_2R C / C-LW
59 TyreD40 C / C-LW
60 RimD40 C
61 Guide C
62 Pin C
63 TyreD25 C / C-LW
64 RimD25 C
65 Tail_fitting C
66 Wheel_fairing_3L C / C-LW
67 Wheel_fairing_3R C / C-LW
PRINTING PARAMETER CATEGORY
A-LW A C-LW C
Layer height (mm) 0.25 0,2 0,15 0,13
Bottom layers 0 0 4 4
Top layers 0 0 6 6
Wall lines / perimeter 1 1 2 2
Nozzle diameter (mm) 0,4 0,4 0,4 0,4
Material LW-PLA PLA/
PETG
LW-PLA PLA/PETG
FLEX/ABS
Infill density (%) 0 0 10 10
Printing temp (°C) 235 220 235 205 to 240
Bed temp (°C) 60 60 60 60
Flow (%) 53 100 53 100
Retraction (mm) 0,5 to 3 0,5 to 3 0,5 to 3 3
Retraction extra prime amount (mm) 0 to 0,7 0 to 0,7 0 0
Speed (mm/s) 55 50 35 25 to 50
Fan YES YES YES YES
Brim (mm) 3 to 5 3 to 5 0 to 3 0 to 3
Minimun layer time (s) 5 5 5 5
Support NO NO NO NO
5
If your motor reach temperatures
over 50 °C use ABS or PETG for "Motor_holder"
6
7
Print "tyre" with flexible material.
8
1- Red parameters are mandatory to ensure airplane
functionality, assembly or weight target.
3-Do not print LW-PLA parts at the same time with
others to avoid stringing in the outer surface.
2-Stringing can not be eliminated for LW-PLA material.
Add 2 bottom layers (parts marked with this flag note)
4-Center of gravity marking under the wing.
Add 8 bottom layers
Add 2 top layers
9
7
9
8
9
7
9
7
9
7
7
9
8
8
9
7
9
7
9
7
9
7
9
7
9
9
7
9
7
9
7
7
9
7
7
9
9
7
9
9
8
5
6
6
6
6
7
9
9
7
32
33
34
36
35
13
14
15
16
17
18
19
22
23
24
25
20
21
37
48
48
48
48
49
49
49
49
50
49
49
49
1
6
7
8
9
10
11
44
44
x2
x2
2
4
V1
V2
41
42
Complete
Half
3
12
X2
43
X2
Alternatively you can fix the
wing with rubber bands
40
x2
B
B
A
A
C
C
51
53
x2
6
6
10
10
10
15
ELEVATOR
Recommended throw
AILERONS
RUDDER
52
x2
134
MAIN LANDING GEAR
54
45
46
x2
x2
Steel rod D2
23
143
Section B-B
(Concept valid also for join
between WingC and Wing1R
61
Section A-A
Glued push rod D1,2
(Not mandatory
for PLA version)
Magnets
10X5X3MM
26
27
28
29
30
31
V1 Winglet
V2 Classic wingtip
WINGTIP DETAIL
62
x4
Nut M3
Bolt M3X30
Washer
Symetry axis
Section C-C
38
39
Push rod D1,2
TAIL SECTION
49
Do not glue the push rod
63
64
47
49
65
143
24
23
55
56
57
58
59
60
66
67