User Manual

ITEM NAME CATEGORY
1 Spinner C
2 Prop_hub C
3 Nose A / A-LW
4 Canopy_1 A / A-LW
5 Canopy_2 A / A-LW
6 Fus1 A / A-LW
7 Fus2 A / A-LW
8 Fus3 A / A-LW
9 Fus4 A / A-LW
10 Fus5 A / A-LW
11 Stab_1L A / A-LW
12 Stab_1R A / A-LW
13 Stab_2L A / A-LW
14 Stab_2R A / A-LW
15 Ruddervator_LH A / A-LW
16 Ruddervator_RH A / A-LW
17 Wing1L A / A-LW
18 Wing1L_F A / A-LW
19 Wing1R A / A-LW
20 Wing1R_F A / A-LW
21 Wing2L A / A-LW
22 Wing2L_F A / A-LW
23 Wing2R A / A-LW
24 Wing2R_F A / A-LW
25 Wing3L A / A-LW
26 Wing3L_F A / A-LW
27 Wing3R A / A-LW
28 Wing3R_F A / A-LW
29 Wing4L A / A-LW
30 Wing4R A / A-LW
31 Wing5L A / A-LW
32 Wing5R A / A-LW
33 Flap1L A / A-LW
34 Flap1R A / A-LW
35 Flap2L A / A-LW
36 Flap2R A / A-LW
37 Aileron1L A / A-LW
38 Aileron1R A / A-LW
39 Aileron2L A / A-LW
40 Aileron2R A / A-LW
41 LG_root C
42 TyreD40 C
43 RimD40 C
44 Servo_holde_wing C
45 Cover_horn C
46 Motor_holder C
47 Magnet_support C
48 Servo_holder_fus C
49 LG_Pin C
50 Hinge_wing C
51 Axis C
52 LG_pin_box C
PRINTING PARAMETER CATEGORY
A-LW A C
Layer height (mm) 0.25 0,2 0,13
Bottom layers 0 0 4
Top layers 0 0 6
Wall lines / perimeter 1 1 2
Nozzle diameter (mm) 0,4 0,4 0,4
Material LW-PLA PLA/
PETG
PLA/PETG
FLEX/ABS
Infill density (%) 0 0 10
Printing temp (°C) 235 220 205 to 240
Bed temp (°C) 60 60 60
Flow (%) 53 100 100
Retraction (mm) 0,5 to 3 0,5 to 3 3
Retraction extra prime amount (mm) 0 to 0,7 0 to 0,7 0
Speed (mm/s) 55 50 25 to 50
Fan YES YES YES
Brim (mm) 3 to 5 3 to 5 0 to 3
Minimun layer time (s) 5 5 5
Support NO NO NO
3
If your motor reach temperatures
over 50 °C use ABS.
4
5
Print "tyre" with flexible material.
6
1- Red parameters are mandatory to ensure airplane
functionality, assembly or weight target.
Add 2 bottom layers.
2-Center of gravity marking under the wing.
Add 8 bottom layers.
Add 4 top layers.
8
4
3
5
7
7
3
7
Version without flaps.
5
5
6
7
5
7
5
7
6
7
7
6
5
5
5
5
8
5
7
5
7
5
7
6
7
7
6
7
6
7
5
7
6
7
5
7
8
8
8
8
8
x4
x4
x2
x4
x2
x16
12
14
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
50
50
50
50
51
51
51
51
51
51
51
51
51
Push rod D1,2
V1
V2
With motor
W/o motor
1
2
3
6
4
5
7
8
9
10
11
13
15
51
51
A
A
B
B
Section A-A
Glued CF rod 1X500
Glued CF tube 8X500
45
44
x2
X2
47
4849
Magnets 10X5X3
Section B-B
41
42
43
Steel rod D2
CF 6X360
CF 8X1000
52
46
13
13
15
15
RUDDERVATORS
Recommended throw
AILERONS
(measured at the root)