MSDS

ManualsBrandsEco-Bond ManualsPaint10.1 oz. Heavy Duty Adhesive (4-Pack)

Lastrevised9/30/2008ECOBONDAdhesivesHD150MaterialDataSafetySheet

Material Data Safety Sheet

ANSI 2400.1 Format

ECO-BOND Adhesives LLC

HD 150

Product Name HD 150

Chemical Family Modified Polymer

Product Use Moisture Cure Sealant

MSDS Prepared 10/23/04

MSDS Prepared by Ed Zimmerman

HAZARDOUS INGREDIENTS

Ingredient Name

CAS Number Concentration

Amino Silane 1760-24-3 1 – 5%

HMIG

Health 1 Flammability 0 Reactivity 0 Protective Equipment B

EMERGENCY OVERVIEW

Human Effects and Symptoms of Exposure

Routes of Entry – Dermal contact, Eye.

Acute Eye Contact – Direct contact can cause severe irritation.

Acute Skin Contact – Direct contact may cause slight irritation.

Skin Absorption – Not Toxic.

Acute Inhalation – Product is extremely low in volatility and therefore not likely to pose a problem from inhalation.

Acute Ingestion – May be harmful if ingested, not a likely route of entry.

Chronic Effects of exposure – Repeated or prolonged direct contact to the eyes may cause chemical burns. Repeated

or prolonged direct contact to the skin may cause adermatitis.

Medical Conditions Aggravated by exposure – Preexisting skin and eye disorders may be aggravated by direct contact

to this product.

Carcinogenicity – There are no components in this product that are listed as a carcinogen by

NTP, IARC, ACGIH or OSHA.

DistributedBy:

ECO‐BONDAdhesives,LLC

N27W23960PaulRoad#202

Pewaukee,WI53072

262‐347‐0136

Section1.ProductandCom

Information



Section2.Com

osition

InformationonIn

redients



Section3.HazardsIdentification



Summary of content (4 pages)

PAGE 1
Material Data Safety Sheet ANSI 2400.1 Format ECO-BOND Adhesives LLC HD 150 Section 1. Product and Company Information Product Name Chemical Family Product Use MSDS Prepared MSDS Prepared by Distributed By: ECO‐BOND Adhesives, LLC N27W23960 Paul Road #202 Pewaukee, WI 53072 262‐347‐0136 HD 150 Modified Polymer Moisture Cure Sealant 10/23/04 Ed Zimmerman Section 2.
PAGE 2
Section 4. First Aid Measures First Aid For Eyes – Flush with large amounts of water for at least 15 minutes. Consult a physician if ill effects or irritation occurs. First Aid For Skin – Clean product from affected area with Ethyl alcohol, then wash with soap and water. First Aid for Inhalation – An unlikely route of entry. Remove to fresh air. Consult a physician. First Aid For Ingestion – An unlikely route of entry. Consult a physician. Section 5.
PAGE 3
Personal Protective Equipment: Eye Protection – Wear safety glasses or goggles to avoid eye contact. Skin Protection – Wear impervious gloves such as vinyl to minimize contact with skin. Respiratory Protection – Not required. Work/Hygienic Practices – Avoid contact with eyes and skin. Wash thoroughly after handling and before eating or drinking. Section 9. Physical and Chemical Properties Physical State……………………….......................................... Paste.
PAGE 4
Section 13. Disposal Considerations If this product as supplied becomes a waste, it does not meet the criteria of a hazardous waste as defined under the Resource Conservation and Recovery Act (RCRA) 40 CFR 261. This product becomes a firm synthetic rubber when cured. Please allow to cure before disposal. Section 14. Transport Information Special Shipping Information – None. DOT – Not regulated. TDG – Not available. PIN – Not available. Section 15. Regulatory Information OSHA 29 CFR 1910-1200 – Irritant.