THE DIRECT-TO-DECK SOLUTION FOR A VARIETY OF ROOF TYPES INSTALLATION GUIDE REVISION: 08/02/22 VERSION: V2.3 ECOFASTENSOLAR.
REVISION: 08/02/22 VERSION: V2.
REVISION: 08/02/22 VERSION: V2.3 44-R 44-R The base plate of the 44-R utilizes eight fasteners, allowing the system to be installed directly to the roof deck without engaging a rafter. The 44-R System can be used on low slope, flat, and SIPs (structural insulated panel) roofs, and with a variety of compression bracket options. 44-R is a customizable solution for new or existing roofs. Extensively tested for pullout and shear.
REVISION: 08/02/22 VERSION: V2.3 44-R INSTALLATION GUIDE SYSTEM COMPONENTS 2 3 5 4 6 7 1. L-FOOT SCL-101 MLL 3” (OTHER OPTIONS AVAILABLE) 2. 3/8” SERRATED FLANGE NUT 3. 3/8” EPDM BONDED WASHER 4. EPDM SEALING WASHER COMPONENTS 1 5. 44-R FLASHING AL BLK 12X14” 6. #15-13 SELF DRILLING FASTENER (8X) 7.
REVISION: 08/02/22 VERSION: V2.3 44-R INSTALLATION GUIDE Locate and mark the location to which the base plate is to be attached. Cut the up-slope shingle the minimal amount needed to install base plate. This will ensure the flashing does not overhang the course below, protect the sides of the base plate, and ensure the best watertight protection for your installation. Attach the base plate to the roof. All fastener holes should be used.
REVISION: 08/02/22 VERSION: V2.3 44-R INSTALLATION GUIDE INSTALLING 44-R Place an EcoFasten bracket onto the stud, followed by the bonded sealing washer with the rubber side facing down. Secure the bracket using the serrated flange nut by tightening it to 50 inch-pounds. INSTALLATION After the flashing is in place, install the EPDM washer over the stud.
REVISION: 08/02/22 VERSION: V2.3 44-R INSTALLATION GUIDE CUT SHEET: 44-R BASE SS 6X6” 44-R BASE SS 6X6” PART NUMBER 3015013 DESCRIPTION 44-R BASE SS 6X6” LINE DRAWINGS 3 2 1 ITEM NO. DESCRIPTION 1 EF-44R-BASE-SS-NDD WELDMENT 2 SS SERRATED FLANGE LOCK NUT, 3/8-16 3 3/8 STAINLESS STEEL AND EPDM BONDED SEALING WASHER 1) EF-44R-BASE-SS-NDD WELDMENT 6.0 8X 0.31 THRU 6.0 0.69 1.0 Material Finish 3/8" THD Stainless Steel Mill REV.
REVISION: 08/02/22 VERSION: V2.
REVISION: 08/02/22 VERSION: V2.3 44-R INSTALLATION GUIDE CUT SHEET: 44-R FLASHING AL BLK 12X14” 44-R FLASHING AL BLK 12X14" DESCRIPTION 44-R FLASHING AL BLK 12X14" LINE DRAWINGS PART NUMBER 3015014 1 2 ITEM NO. 1 2 DESCRIPTION EFL-44R-1214-BLK FLASHING EPDM SEALING WASHER 1) EFL-44R-1214-BLK FLASHING 11.88 14.0 0.47 THRU 0.39 Material Finish Aluminum Black REV.
REVISION: 08/02/22 VERSION: V2.
REVISION: 08/02/22 VERSION: V2.3 44-R INSTALLATION GUIDE CUT SHEET: L-FOOT L-102 BLK 3” L-FOOT L-102 BLK 3" DESCRIPTION L-FOOT L-102 BLK 3" 1 2 3 ITEM NO. DESCRIPTION 1 L-102-3 ANOD BLK 2 SS HEX HD CAP SCREW, FULL THD, 3/8-16 UNC X 1.25 LONG 3 SS SERRATED FLANGE LOCK NUT, 3/8-16 1) L-102-3 ANOD BLK 0.38 THRU ALL 1.88 0.42 2X 0.41 2X 0.46 3.0 1.92 Material Finish LINE DRAWINGS PART NUMBER 3011015 Aluminum Black REV.
REVISION: 08/02/22 VERSION: V2.3 44-R INSTALLATION GUIDE CUT SHEET: L-FOOT L-102 MLL 6” L-FOOT L-102 MLL 6" DESCRIPTION L-FOOT L-102 MLL 6" 1 2 3 ITEM NO. 1 2 3 DESCRIPTION L-102-6 SS HEX HD CAP SCREW, FULL THD, 3/8-16 UNC X 1.25 LONG SS SERRATED FLANGE LOCK NUT, 3/8-16 1) L-102-6 0.38 THRU ALL 2.0 0.41 2X 0.41 2X 1.6 6.0 3.02 Material Finish LINE DRAWINGS PART NUMBER 3011016 Aluminum Mill REV.
REVISION: 08/02/22 VERSION: V2.3 44-R INSTALLATION GUIDE CUT SHEET: L-FOOT SCL-101 MLL 3” L-FOOT SCL-101 MLL 3" DESCRIPTION L-FOOT SCL-101 MLL 3" 1 2 3 ITEM NO. 1 2 3 DESCRIPTION L FOOT W/ STANDARD DIMPLE AND OPEN SLOT, 3 IN TALL MLL SS HEX HD CAP SCREW, FULL THD, 3/8-16 UNC X 1.25 LONG SS SERRATED FLANGE LOCK NUT, 3/8-16 1) L FOOT W/ STANDARD DIMPLE AND OPEN SLOT, 3 IN TALL MLL 0.38 THRU ALL 1.88 0.41 0.42 1.75 3.0 1.92 Material Finish LINE DRAWINGS PART NUMBER 3011017 Aluminum Mill REV.
REVISION: 08/02/22 VERSION: V2.3 44-R INSTALLATION GUIDE CUT SHEET: L-FOOT SCL-101 BLK 3” L-FOOT SCL-101 BLK 3" DESCRIPTION L-FOOT SCL-101 BLK 3" 1 2 3 ITEM NO. DESCRIPTION 1 L FOOT W/ STANDARD DIMPLE AND OPEN SLOT, 3 IN TALL BLK 2 SS HEX HD CAP SCREW, FULL THD, 3/8-16 UNC X 1.25 LONG 3 SS SERRATED FLANGE LOCK NUT, 3/8-16 1) L FOOT W/ STANDARD DIMPLE AND OPEN SLOT, 3 IN TALL BLK 0.38 THRU ALL 1.88 0.42 0.41 1.75 3.0 1.92 Material Finish LINE DRAWINGS PART NUMBER 3011018 Aluminum Mill REV.
REVISION: 08/02/22 VERSION: V2.3 44-R INSTALLATION GUIDE CUT SHEET: CF UNIV L-FOOTMLL MLL 3” CF UNIV L-FOOT 3" DESCRIPTION CF UNIV L-FOOT MLL 3" 1 ITEM NO. DESCRIPTION 1 CLICKFIT L FOOT ASSEMBLY LINE DRAWINGS PART NUMBER 2012022 1) CLICKFIT L FOOT ASSEMBLY 0.79 THRU 1.79 3.06 2.76 0.38 THRU Material Finish Aluminum/Stainless Steel Mill REV.
REVISION: 08/02/22 VERSION: V2.3 44-R INSTALLATION GUIDE DECK SCREW SS SS DECK SCREW DESCRIPTION DECK SCREW SS #15X2" DECK SCREW SS #15X3" DECK SCREW SS #15X4" LENGTH (L) 2" 3" 4" LINE DRAWINGS PART NUMBER 3016010 3016011 3016012 1 ITEM NO. 1 DESCRIPTION ROOFING SCREW, DRILL POINT, BLACK 1) ROOFING SCREW, DRILL POINT, BLACK 0.44 1/4" THD 0.11 L Material Finish Steel Black REV.
REVISION: 08/02/22 VERSION: V2.3 44-R INSTALLATION GUIDE SYSTEM COMPONENTS 1. 44-R BASE SS 6X6” - Base Plate and Hardware: Consists of (1) stainless steel base plate with (1) integrated stainless steel stainless steel / EPDM bonded sealing washer. Base Plate is 11 gauge 304 stainless steel with one 3/8”-304 stainless steel screw welded into embossed countersink. 2. 44-R FLASHING AL BLK 12X14” - Aluminum Flashing: Black finish (Kynar painted) .032 gauge aluminum, embossed. 3.
REVISION: 08/02/22 VERSION: V2.3 44-R PATENTS Visit www.efpatents.com for patent information. DESIGN REQUIREMENTS 1. Bracket spacing to be recommended by project engineer. 2. Install a minimum of eight fasteners per base plate. 3. It is important to design new structures or assess existing structures to make sure they withstand retained loads. EXAMINATION 1.
