COMPLETE MOUNT & FLASHING ASSEMBLY INSTALLATION GUIDE REVISION: 08/02/22 VERSION: V2.5 ECOFASTENSOLAR.
REVISION: 08/02/22 VERSION: V2.
REVISION: 08/02/22 VERSION: V2.5 GF-1 GF-1 GF-1 is our most versatile solution for composition shingle roofs. Install the flashing using a single fastener for a quick & easy installation. When using the GF-1 flashing grommet and an EcoFasten compression bracket, a watertight seal is created, maintaining the integrity of the roof.
REVISION: 08/02/22 VERSION: V2.5 GF-1 INSTALLATION GUIDE SYSTEM COMPONENTS 2 3 4 1. L-FOOT SCL-101 BLK 3" (OTHER OPTIONS AVAILABLE) 2. 5/16" LAG BOLT (AVAILABLE IN 3” AND 4”) 4. GF-1 FLASHING GLV MLL 8X12" GALVALUME FLASHING WITH PREINSTALLED EPDM RUBBER GASKET COMPONENTS 1 (AVAILABLE IN 8X10 & 8X12, WITH MILL & BLACK FINISH OPTIONS) 3.
REVISION: 08/02/22 VERSION: V2.5 GF-1 INSTALLATION GUIDE Snap horizontal lines across the roof to mark the mount rows, then locate the rafter and mark the installation position of each GF-1 flashing. Drill a 7/32” pilot hole into the rafter or structural member for the lag screw. Backfill with sealant compatible with the roof type. Slide flashing up under the next row of shingles directly above the pilot hole, taking care to align the hole in the flashing with the pilot hole.
REVISION: 08/02/22 VERSION: V2.5 GF-1 INSTALLATION GUIDE Thread the EPDM bonded washer onto the lag bolt followed by one of EcoFasten’s compression brackets and then insert the lag bolt into the gasketed hole in the flashing. Drive the lag bolt down into the rafter using an impact driver. Torque range is between 100-400 torque inch-pounds depending on the type of wood and time of year.
REVISION: 08/02/22 VERSION: V2.5 GF-1 INSTALLATION GUIDE CUT SHEET: GF-1 FLASHING GLV BLK 8X12" GF-1 FLASHING GLV BLK 8X12" DESCRIPTION GF-1 FLASHING GLV BLK 8X12" LINE DRAWINGS PART NUMBER 3012010 1 ITEM NO. 1 DESCRIPTION GF1-GAL-BLK-812 1) GF1-GAL-BLK-812 8.0 12.0 0.3 THRU 0.02 0.31 Material Finish Corrosion Resistant Steel Black REV.
REVISION: 08/02/22 VERSION: V2.5 GF-1 INSTALLATION GUIDE CUT SHEET: GF-1 FLASHING GLV MLL 8X12" GF-1 FLASHING GLV MLL 8X12" DESCRIPTION GF-1 FLASHING GLV MLL 8X12" LINE DRAWINGS PART NUMBER 3012011 1 ITEM NO. 1 DESCRIPTION GF1-GAL-MLL-812 1) GF1-GAL-MLL-812 8.0 12.0 0.3 THRU 0.31 0.02 Material Finish Corrosion Resistant Steel Mill REV.
REVISION: 08/02/22 VERSION: V2.5 GF-1 INSTALLATION GUIDE CUT SHEET: GF-1 FLASHING GLV BLK 8X10" GF-1 FLASHING GLV BLK 8X10" DESCRIPTION GF-1 FLASHING GLV BLK 8X10" LINE DRAWINGS PART NUMBER 3012020 1 ITEM NO. 1 DESCRIPTION GF1M-GAL-BLK-810 W/O WASHER ASSEMBLY 1) GF1M-GAL-BLK-810 W/O WASHER ASSEMBLY 8.0 10.0 0.3 THRU 0.31 0.02 Material Finish Corrosion Resistant Steel Black REV.
REVISION: 08/02/22 VERSION: V2.5 GF-1 INSTALLATION GUIDE CUT SHEET: GF-1 FLASHING AL BLK 8X12" GF-2V FLASHING AL BLK 8X12" DESCRIPTION GF-2V FLASHING AL BLK 8X12" LINE DRAWINGS PART NUMBER 3012013 1 ITEM NO. 1 DESCRIPTION GF2V 8X12 MATTE BLK FLASHING 1) GF2V 8X12 MATTE BLK FLASHING 2X 0.3 THRU 0.31 0.03 Material Finish Aluminum Black REV.
REVISION: 08/02/22 VERSION: V2.5 GF-1 INSTALLATION GUIDE CUT SHEET: L-FOOT L-102 BLK 3” L-FOOT L-102 BLK 3" DESCRIPTION L-FOOT L-102 BLK 3" 1 2 3 ITEM NO. DESCRIPTION 1 L-102-3 ANOD BLK 2 SS HEX HD CAP SCREW, FULL THD, 3/8-16 UNC X 1.25 LONG 3 SS SERRATED FLANGE LOCK NUT, 3/8-16 1) L-102-3 ANOD BLK 0.38 THRU ALL 1.88 0.42 2X 0.41 2X 0.46 3.0 1.92 Material Finish LINE DRAWINGS PART NUMBER 3011015 Aluminum Black REV.
REVISION: 08/02/22 VERSION: V2.5 GF-1 INSTALLATION GUIDE CUT SHEET: L-FOOT L-102 MLL 6” L-FOOT L-102 MLL 6" DESCRIPTION L-FOOT L-102 MLL 6" 1 2 3 ITEM NO. 1 2 3 DESCRIPTION L-102-6 SS HEX HD CAP SCREW, FULL THD, 3/8-16 UNC X 1.25 LONG SS SERRATED FLANGE LOCK NUT, 3/8-16 1) L-102-6 0.38 THRU ALL 2.0 0.41 2X 0.41 2X 1.6 6.0 3.02 Material Finish LINE DRAWINGS PART NUMBER 3011016 Aluminum Mill REV.
REVISION: 08/02/22 VERSION: V2.5 GF-1 INSTALLATION GUIDE CUT SHEET: L-FOOT SCL-101 MLL 3” L-FOOT SCL-101 MLL 3" DESCRIPTION L-FOOT SCL-101 MLL 3" 1 2 3 ITEM NO. 1 2 3 DESCRIPTION L FOOT W/ STANDARD DIMPLE AND OPEN SLOT, 3 IN TALL MLL SS HEX HD CAP SCREW, FULL THD, 3/8-16 UNC X 1.25 LONG SS SERRATED FLANGE LOCK NUT, 3/8-16 1) L FOOT W/ STANDARD DIMPLE AND OPEN SLOT, 3 IN TALL MLL 0.38 THRU ALL 1.88 0.41 0.42 1.75 3.0 1.92 Material Finish LINE DRAWINGS PART NUMBER 3011017 Aluminum Mill REV.
REVISION: 08/02/22 VERSION: V2.5 GF-1 INSTALLATION GUIDE CUT SHEET: L-FOOT SCL-101 BLK 3” L-FOOT SCL-101 BLK 3" DESCRIPTION L-FOOT SCL-101 BLK 3" 1 2 3 ITEM NO. DESCRIPTION 1 L FOOT W/ STANDARD DIMPLE AND OPEN SLOT, 3 IN TALL BLK 2 SS HEX HD CAP SCREW, FULL THD, 3/8-16 UNC X 1.25 LONG 3 SS SERRATED FLANGE LOCK NUT, 3/8-16 1) L FOOT W/ STANDARD DIMPLE AND OPEN SLOT, 3 IN TALL BLK 0.38 THRU ALL 1.88 0.42 0.41 1.75 3.0 1.92 Material Finish LINE DRAWINGS PART NUMBER 3011018 Aluminum Mill REV.
REVISION: 08/02/22 VERSION: V2.5 GF-1 INSTALLATION GUIDE CUT SHEET: CF UNIV L-FOOTMLL MLL 3” CF UNIV L-FOOT 3" DESCRIPTION CF UNIV L-FOOT MLL 3" 1 ITEM NO. DESCRIPTION 1 CLICKFIT L FOOT ASSEMBLY LINE DRAWINGS PART NUMBER 2012022 1) CLICKFIT L FOOT ASSEMBLY 0.79 THRU 1.79 3.06 2.76 0.38 THRU Material Finish Aluminum/Stainless Steel Mill REV.
REVISION: 08/02/22 VERSION: V2.5 GF-1 INSTALLATION GUIDE CUT SHEET: LAGSS SCREW SS W/BW .313X4(50) LAG SCREW .313X4” DESCRIPTION LAG SCREW SS .313X4” W/BW (50) LINE DRAWINGS PART NUMBER 3016017 1 ITEM NO. 1 DESCRIPTION LAG SCREW, 5/16-4", THREAD 3", EPDM BACKED WASHER 1) LAG SCREW, 5/16-4", THREAD 3", EPDM BACKED WASHER 0.75 1 2 " Head 5/16" THD 0.34 Material Finish 3.87 Stainless Steel/EPDM Mill REV.
REVISION: 08/02/22 VERSION: V2.5 GF-1 INSTALLATION GUIDE CUT SHEET: EPDMWASHER BOND WASHER .313" (51) EPDM BOND SS .313"SS (51) PART NUMBER 3016014 DESCRIPTION EPDM BOND WASHER SS .313" (51) ITEM NO. 1 LINE DRAWINGS 1 DESCRIPTION 5/16 STAINLESS STEEL AND EPDM BONDED SEALING WASHER 1) 5/16 STAINLESS STEEL AND EPDM BONDED SEALING WASHER 0.13 0.75 0.28 THRU Material Finish Stainless Steel/EPDM Mill REV.
REVISION: 08/02/22 VERSION: V2.5 GF-1 INSTALLATION GUIDE CUT RI COMP SLIDE ALBLK BLK RISHEET: COMP SLIDE AL PART NUMBER DESCRIPTION 2011013 RI COMP SLIDE AL BLK LINE DRAWINGS 1 2 ITEM NO. DESCRIPTION 1 ROCKIT V3 SLIDECOMP 2 LAG SCREW, 5/16-4", THREAD 3", EPDM BACKED WASHER 1) ROCKIT V3 SLIDECOMP 0.38 4.0 0.03 1.5 1.75 2.0 Material Finish Aluminum Black REV.
REVISION: 08/02/22 VERSION: V2.5 GF-1 INSTALLATION GUIDE SYSTEM COMPONENTS 1. GF-1 Flashing: All flashing options come with a pre-installed integrated EPDM grommet options: 2. 1. 8 x 12" .032 gauge galvalume with mill or black (kynar painted) finish. 2. 8 x 10" .032 gauge galvalume with black (kynar painted) finish. 3. 8 x 12" .032 gauge aluminum with black (kynar painted) finish. Aluminum Compression Bracket: Compatible with a variety of EcoFasten compression brackets.
REVISION: 08/02/22 VERSION: V2.5 GF-1 FLORIDA PRODUCT APPROVAL Approved for any combination of 8”x12” GF-1 flashing with the ClickFit L-foot & Lag Screw. PATENTS Visit www.efpatents.com for patent information. DESIGN REQUIREMENTS 1. Bracket spacing to be recommended by project engineer. 2. It is important to design new structures or assess existing structures to make sure they withstand retained loads. EXAMINATION 1.
