VERSATILE FLASHED BASE PLATE INSTALLATION GUIDE REVISION:08/02/22 08/02/22 VERSION: V2.3 WIP_V1.0 ECOFASTENSOLAR.
REVISION: 08/02/22 VERSION: V2.
REVISION: 08/02/22 VERSION: V2.3 QUIKFOOT QUIK FOOT QuikFoot includes a base plate and uses two self-drilling attachment points for optimal pullout value. When paired with an EcoFasten compression bracket, the QuikFoot flashing creates a watertight seal that will maintain the roof’s integrity.
REVISION: 08/02/22 VERSION: V2.3 QUIKFOOT INSTALLATION GUIDE SYSTEM COMPONENTS 1 3 5 4 6 1. L-FOOT SCL-101 BLK 3” (OTHER OPTIONS AVAILABLE) 2. 5/16" SERRATED FLANGE NUT 3. 5/16" EPDM BONDED SEALING WASHER 7 COMPONENTS 2 4. EPDM SEALING WASHER 5. QF FLASHING AL BLK 8X12" 6. #15-13 SELF DRILLING FASTENER (2X) 7. QF BASE AL 1.
REVISION: 08/02/22 VERSION: V2.3 QUIKFOOT INSTALLATION GUIDE Snap horizontal chalk lines to mark the position of each row. Find the rafters and mark the position for installation. Place the QF Base over the rafter vertically and screw down using two fasteners. The stud on the base plate should line up with the chalk line. Slide the flashing over the base plate and under the row of shingles directly above the base plate.
REVISION: 08/02/22 VERSION: V2.3 QUIKFOOT INSTALLATION GUIDE Place the bare EPDM washer over the stud, pushing it all the way down. Then place an EcoFasten compression bracket over the stud and bare EPDM washer, followed by the bonded sealing washer with the rubber side facing down. Secure the bracket to the stud using the serrated flange nut and torque to 50-inch pounds.
REVISION: 08/02/22 VERSION: V2.3 QUIKFOOT INSTALLATION GUIDE PART NUMBER 3012014 DESCRIPTION QF BASE AL 1.25" 2 3 1 ITEM NO. DESCRIPTION 1 QF BASE AL 1.25", ASSEMBLY 2 SS SERRATED FLANGE LOCK NUT, 3/8-16 3 3/8 STAINLESS STEEL AND EPDM BONDED SEALING WASHER 1) QF BASE AL 1.25", ASSEMBLY 3.25 2X 0.33 THRU ALL 1.5 3/8" THD 1.34 1.02 Material Finish LINE DRAWINGS CUT QF1.25" BASE AL 1.25" QFSHEET: BASE AL Aluminum/Steel Mill REV.
REVISION: 08/02/22 VERSION: V2.3 QUIKFOOT INSTALLATION GUIDE LINE DRAWINGS CUT SHEET: QF BASE AL 1.
REVISION: 08/02/22 VERSION: V2.3 QUIKFOOT INSTALLATION GUIDE CUT QF FLASHING AL BLK 8X12 QFSHEET: FLASHING AL BLK 8X12" DESCRIPTION QF FLASHING AL BLK 8X12" LINE DRAWINGS PART NUMBER 3012016 1 2 ITEM NO. 1 2 DESCRIPTION QFL 8X12 MATTE BLK FLASHING EPDM SEALING WASHER 1) QFL 8X12 MATTE BLK FLASHING 8.0 12.0 0.47 THRU 0.51 Material Finish Aluminum Black REV.
REVISION: 08/02/22 VERSION: V2.
REVISION: 08/02/22 VERSION: V2.3 QUIKFOOT INSTALLATION GUIDE CUT SHEET: L-FOOT L-102 BLK 3” PART NUMBER 3011015 DESCRIPTION L-FOOT L-102 BLK 3" 1 2 3 ITEM NO. DESCRIPTION 1 L-102-3 ANOD BLK 2 SS HEX HD CAP SCREW, FULL THD, 3/8-16 UNC X 1.25 LONG 3 SS SERRATED FLANGE LOCK NUT, 3/8-16 1) L-102-3 ANOD BLK 0.38 THRU ALL 1.88 0.42 2X 0.41 2X 0.46 3.0 LINE DRAWINGS L-FOOT L-102 BLK 3" 1.92 Material Finish Aluminum Black REV.
REVISION: 08/02/22 VERSION: V2.3 QUIKFOOT INSTALLATION GUIDE CUT SHEET: L-FOOT L-102 MLL 6” PART NUMBER 3011016 DESCRIPTION L-FOOT L-102 MLL 6" 1 2 3 ITEM NO. 1 2 3 DESCRIPTION L-102-6 SS HEX HD CAP SCREW, FULL THD, 3/8-16 UNC X 1.25 LONG SS SERRATED FLANGE LOCK NUT, 3/8-16 1) L-102-6 0.38 THRU ALL 2.0 0.41 2X 0.41 2X 1.6 6.0 LINE DRAWINGS L-FOOT L-102 MLL 6" 3.02 Material Finish Aluminum Mill REV.
REVISION: 08/02/22 VERSION: V2.3 QUIKFOOT INSTALLATION GUIDE CUT SHEET: L-FOOT SCL-101 MLL 3” PART NUMBER 3011017 DESCRIPTION L-FOOT SCL-101 MLL 3" 1 2 3 ITEM NO. 1 2 3 DESCRIPTION L FOOT W/ STANDARD DIMPLE AND OPEN SLOT, 3 IN TALL MLL SS HEX HD CAP SCREW, FULL THD, 3/8-16 UNC X 1.25 LONG SS SERRATED FLANGE LOCK NUT, 3/8-16 1) L FOOT W/ STANDARD DIMPLE AND OPEN SLOT, 3 IN TALL MLL 0.38 THRU ALL 1.88 0.41 0.42 1.75 3.0 LINE DRAWINGS L-FOOT SCL-101 MLL 3" 1.
REVISION: 08/02/22 VERSION: V2.3 QUIKFOOT INSTALLATION GUIDE CUT SHEET: L-FOOT SCL-101 BLK 3” PART NUMBER 3011018 DESCRIPTION L-FOOT SCL-101 BLK 3" 1 2 3 ITEM NO. DESCRIPTION 1 L FOOT W/ STANDARD DIMPLE AND OPEN SLOT, 3 IN TALL BLK 2 SS HEX HD CAP SCREW, FULL THD, 3/8-16 UNC X 1.25 LONG 3 SS SERRATED FLANGE LOCK NUT, 3/8-16 1) L FOOT W/ STANDARD DIMPLE AND OPEN SLOT, 3 IN TALL BLK 0.38 THRU ALL 1.88 0.42 0.41 1.75 3.0 LINE DRAWINGS L-FOOT SCL-101 BLK 3" 1.
REVISION: 08/02/22 VERSION: V2.3 QUIKFOOT INSTALLATION GUIDE PART NUMBER 2012022 DESCRIPTION CF UNIV L-FOOT MLL 3" LINE DRAWINGS CUT SHEET: CF UNIV L-FOOTMLL MLL 3” CF UNIV L-FOOT 3" 1 ITEM NO. DESCRIPTION 1 CLICKFIT L FOOT ASSEMBLY 1) CLICKFIT L FOOT ASSEMBLY 0.79 THRU 1.79 3.06 2.76 0.38 THRU Material Finish Aluminum/Stainless Steel Mill REV.
REVISION: 08/02/22 VERSION: V2.3 QUIKFOOT INSTALLATION GUIDE DECK SCREW SS SS DECK SCREW DESCRIPTION DECK SCREW SS #15X2" DECK SCREW SS #15X3" DECK SCREW SS #15X4" LENGTH (L) 2" 3" 4" LINE DRAWINGS PART NUMBER 3016010 3016011 3016012 1 ITEM NO. 1 DESCRIPTION ROOFING SCREW, DRILL POINT, BLACK 1) ROOFING SCREW, DRILL POINT, BLACK 0.44 1/4" THD 0.11 L Material Finish Steel Black REV.
REVISION: 08/02/22 VERSION: V2.3 QUIKFOOT INSTALLATION GUIDE SYSTEM COMPONENTS 1. QF Base AL 1/25": Consists of (1) stainless steel base plate attachment bracket with (1) preEPDM sealing washer. Base is made out of 6000 series aluminum. 2. QF FLASHING AL BLK 8X12": Black finish (Kynar painted) .032 gauge aluminum, embossed. 3. Fastener: Self-drilling #15 roofing screws are available from Ecofasten in 2”, 3” and 4” lengths.
REVISION: 08/02/22 VERSION: V2.3 QUIKFOOT DESIGN REQUIREMENTS 1. Bracket spacing to be recommended by project engineer. 2. Install a minimum of two fasteners per base plate. 3. It is important to design new structures or assess existing structures to make sure they withstand retained loads. EXAMINATION 1. Substrate: Inspect structure on which brackets are to be installed and verify that it will withstand any additional loading that may be incurred. 2.
