User Guide Extra Battery Contact us: support@ecoflow.com www.ecoflow.com WARNING 1. Please keep the product dry, do not expose it to high heat. Pay attention to the safety when carrying the product. 2. Never disassemble, puncture, shock, crash, or incinerate the product or the accessories. 3. After removing the package, the Max Module must be installed with RIVER 600 in time. Please pay attention to static electricity during the installation process. 4.
Glossary The following terms are used in this document to indicate various levels of potential harm that may be caused by improper operation. NOTICE The instructions, if not properly followed, may result in property damage and minor physical damage. CAUTION The instructions, if not properly followed, may result in property damage and serious physical damage. Warning The instructions, if not properly followed, may result in property damage, major accident and serious injury.
Installation Notes: 1. The Extra Battery Module must be installed with RIVER 600 before it can be used. It cannot be used alone. 2. During the install process, you must pay attention to anti-static protection to ensure that there is no static electricity on the human body and around. Static electricity may cause damage to the product. 3. RIVER 600 must be turned off before the install process. 4. The screws must be tightened to ensure the RIVER 600 is locked with the extra battery module. Product Use: 1.
Product Charging 1. Always use EcoFlow approved charge cables. EcoFlow does not response to any damage caused by using non-EcoFlow charging cable. 2. When charging, please place the product on the ground with no flammable or combustible materials around. To prevent accidents, never leave the battery unattended during charging. 3. DO NOT charge a product immediately after a long heavy load, because the product’s temperature may be too high. DO NOT charge a product until it cools down to room temperature.
CONTENTS RIVER 600 Extra Battery Use Care and Safety Guide 1 RIVER 600 Extra Battery Module Installation Instructions 2 Ambient Light Area 6 Technical Specifications 7 What’s in the Box 7
RIVER 600 Extra Battery Module Use Care and Safety Guide CONGRATULATIONS! You now own the best quality portable power station Extra Battery in the world. This pamphlet is meant to help you. Please take some time to read it and install the Extra Battery Module according to the instructions on the manual. You can fully understand how to use the Extra Battery Module and increase the experience of using Portable Lithium Generator! NOTICE Make sure to turn off the RIVER 600 before install the expansion battery.
RIVER 600 Extra Battery Module Installation Instructions 1 Female battery socket Ambient light and signal indication 2 1. Female Battery Socket And Installation Instructions 1. Please make sure that the RIVER 600 is turned off. Take out the screwdriver from the extra battery module kit and locate the four screws on the bottom cover. Note: Please pay attention to prevent static electricity during the installation process.
Male battery socket Short screws 2. Please unscrew the 4 screws according to the figure and remove the bottom cover. You can see the male battery socket. The extra battery module should be positioned as shown in the figure. (Please note that only the bottom cover needs to be remove. Do not remove the top cover.
Long screws 3. Align the male and female battery sockets and connect them. Close the botton cover. Take the four long screws from the kit and screw them on the screw mouth.
Extra battery module indicator *Ambient light area 4. Put the RIVER 600 upright and turn it on. The extra battery module’s ambient light will turn blue. If the extra battery module indicator light is shown on the RIVER 600’s display, the extra battery module is activated successfully. Please make sure the machine is fully charged before use. If the ambient light or the extra battery module indicator light is not active, repeat Step 2 then check the connection.
*Ambient Light Area 1. Status Signals Powering up: The blue light will move from the middle to the sides Powering down: The blue light will move from the sides to the middle. Charging: The blue light will move from left to right repeatedly. 2. Customizing the Ambient Light Click the Module Settings to set various functions. 1. You can set up to turn on/off the ambient light or keep the light always on (the ambient light can also be on in standby mode). 2. You can select the color you prefer. 3.
Technical Specifications General Specs Net Weight * 5.5lbs (2.5kg) Dimensions * 11.2 x 7 x 2.3in (28.5 x 18 x 5.9cm) Capacity 288Wh (28.8V) Testing and certification UL Standard, CE, FCC, RoHS Battery Cell Chemistry Lithium-ion Discharge Temperature -4 to 140°F +/-5°F(-20 to 60°C +/-3°C) Charge Temperature 32 to 113°F +/-5°F(0 to 45°C +/-3°C) Shelf Life 1 Year (after fully charged) Cycle Life 500 Cycles (80%) *Please Note: The above weight, size, etc. have certain measurement errors.