Product Specs
Table Of Contents
- 1Revision history
- 2About this document
- 3Block diagram
- 4Pin assignments
- 5Absolute maximum ratings
- 6Recommended operating conditions
- 7CPU
- 8Memory
- 9AHB multilayer
- 10EasyDMA
- 11NVMC — Non-volatile memory controller
- 12BPROT — Block protection
- 13FICR — Factory information configuration registers
- 14UICR — User information configuration registers
- 14.1Registers
- Table 18: Instances
- 14.1.2NRFFW[1]
- 14.1.3NRFFW[2]
- 14.1.4NRFFW[3]
- 14.1.5NRFFW[4]
- 14.1.6NRFFW[5]
- 14.1.7NRFFW[6]
- 14.1.8NRFFW[7]
- 14.1.9NRFFW[8]
- 14.1.10NRFFW[9]
- 14.1.11NRFFW[10]
- 14.1.12NRFFW[11]
- 14.1.13NRFFW[12]
- 14.1.14NRFFW[13]
- 14.1.15NRFFW[14]
- 14.1.16NRFHW[0]
- 14.1.17NRFHW[1]
- 14.1.18NRFHW[2]
- 14.1.19NRFHW[3]
- 14.1.20NRFHW[4]
- 14.1.21NRFHW[5]
- 14.1.22NRFHW[6]
- 14.1.23NRFHW[7]
- 14.1.24NRFHW[8]
- 14.1.25NRFHW[9]
- 14.1.26NRFHW[10]
- 14.1.27NRFHW[11]
- 14.1.60PSELRESET[0]
- 14.1.61PSELRESET[1]
- 14.1.63NFCPINS
- 14.1Registers
- 15Peripheral interface
- 16Debug and trace
- 17Power and clock management
- 18POWER — Power supply
- 18.1Regulators
- 18.2System OFF mode
- 18.3System ON mode
- 18.4Power supply supervisor
- 18.5RAM sections
- 18.6Reset
- 18.7Retained registers
- 18.8Reset behavior
- 18.9Registers
- Table 23: Instances
- 18.9.6POFCON
- 18.9.7GPREGRET
- 18.9.8GPREGRET2
- 18.9.9RAMON ( Deprecated )
- 18.9.10RAMONB ( Deprecated )
- 18.9.12RAM[0].POWER
- 18.9.13RAM[0].POWERSET
- 18.9.14RAM[0].POWERCLR
- 18.9.15RAM[1].POWER
- 18.9.16RAM[1].POWERSET
- 18.9.17RAM[1].POWERCLR
- 18.9.18RAM[2].POWER
- 18.9.19RAM[2].POWERSET
- 18.9.20RAM[2].POWERCLR
- 18.9.21RAM[3].POWER
- 18.9.22RAM[3].POWERSET
- 18.9.23RAM[3].POWERCLR
- 18.9.24RAM[4].POWER
- 18.9.25RAM[4].POWERSET
- 18.9.26RAM[4].POWERCLR
- 18.9.27RAM[5].POWER
- 18.9.28RAM[5].POWERSET
- 18.9.29RAM[5].POWERCLR
- 18.9.30RAM[6].POWER
- 18.9.31RAM[6].POWERSET
- 18.9.32RAM[6].POWERCLR
- 18.9.33RAM[7].POWER
- 18.9.34RAM[7].POWERSET
- 18.9.35RAM[7].POWERCLR
- 18.10Electrical specification
- 19CLOCK — Clock control
- 20GPIO — General purpose input/output
- 21GPIOTE — GPIO tasks and events
- 22PPI — Programmable peripheral interconnect
- 23RADIO — 2.4 GHz Radio
- Figure 29: RADIO block diagram
- 23.1EasyDMA
- 23.2Packet configuration
- 23.3Maximum packet length
- 23.4Address configuration
- 23.5Data whitening
- 23.6CRC
- 23.7Radio states
- 23.8Transmit sequence
- 23.9Receive sequence
- 23.10Received Signal Strength Indicator (RSSI)
- 23.11Interframe spacing
- 23.12Device address match
- 23.13Bit counter
- 23.14Registers
- 23.15Electrical specification
- 24TIMER — Timer/counter
- 25RTC — Real-time counter
- 26RNG — Random number generator
- 27TEMP — Temperature sensor
- 28ECB — AES electronic codebook mode encryption
- 29CCM — AES CCM mode encryption
- Figure 59: Key-stream generation followed by encry
- 29.1Shared resources
- 29.2Encryption
- 29.3Decryption
- 29.4AES CCM and RADIO concurrent operation
- 29.5Encrypting packets on-the-fly in radio transmit mo
- 29.6Decrypting packets on-the-fly in radio receive mod
- 29.7CCM data structure
- 29.8EasyDMA and ERROR event
- 29.9Registers
- 30AAR — Accelerated address resolver
- 31SPIM — Serial peripheral interface master with Eas
- 32SPIS — Serial peripheral interface slave with Easy
- Figure 73: SPI slave
- 32.1Shared resources
- 32.2EasyDMA
- 32.3SPI slave operation
- 32.4Pin configuration
- 32.5Registers
- Table 71: Instances
- 32.5.8PSELMISO ( Deprecated )
- 32.5.9PSELMOSI ( Deprecated )
- 32.5.10PSELCSN ( Deprecated )
- 32.5.13PSEL.MOSI
- 32.5.15RXDPTR ( Deprecated )
- 32.5.16MAXRX ( Deprecated )
- 32.5.17AMOUNTRX ( Deprecated )
- 32.5.19RXD.MAXCNT
- 32.5.20RXD.AMOUNT
- 32.5.21TXDPTR ( Deprecated )
- 32.5.22MAXTX ( Deprecated )
- 32.5.23AMOUNTTX ( Deprecated )
- 32.5.25TXD.MAXCNT
- 32.5.26TXD.AMOUNT
- 32.5.28DEF
- 32.6Electrical specification
- 33TWIM — I2C compatible two-wire interface master wi
- 34TWIS — I2C compatible two-wire interface slave wit
- Figure 86: TWI slave with EasyDMA
- Figure 87: A typical TWI setup comprising one mast
- Figure 88: TWI slave state machine
- 34.1Shared resources
- 34.2EasyDMA
- 34.3TWI slave responding to a read command
- 34.4TWI slave responding to a write command
- 34.5Master repeated start sequence
- 34.6Terminating an ongoing TWI transaction
- 34.7Low power
- 34.8Slave mode pin configuration
- 34.9Registers
- 34.10Electrical specification
- 35UARTE — Universal asynchronous receiver/ transmitt
- 36QDEC — Quadrature decoder
- 37SAADC — Successive approximation analog-to- digita
- 37.1Shared resources
- 37.2Overview
- 37.3Digital output
- 37.4Analog inputs and channels
- 37.5Operation modes
- 37.6EasyDMA
- 37.7Resistor ladder
- 37.8Reference
- 37.9Acquisition time
- 37.10Limits event monitoring
- 37.11Registers
- Table 89: Instances
- 37.11.7CH[0].PSELN
- 37.11.8CH[0].CONFIG
- 37.11.9CH[0].LIMIT
- 37.11.11CH[1].PSELN
- 37.11.12CH[1].CONFIG
- 37.11.13CH[1].LIMIT
- 37.11.15CH[2].PSELN
- 37.11.16CH[2].CONFIG
- 37.11.17CH[2].LIMIT
- 37.11.19CH[3].PSELN
- 37.11.20CH[3].CONFIG
- 37.11.21CH[3].LIMIT
- 37.11.23CH[4].PSELN
- 37.11.24CH[4].CONFIG
- 37.11.25CH[4].LIMIT
- 37.11.27CH[5].PSELN
- 37.11.28CH[5].CONFIG
- 37.11.29CH[5].LIMIT
- 37.11.31CH[6].PSELN
- 37.11.32CH[6].CONFIG
- 37.11.33CH[6].LIMIT
- 37.11.35CH[7].PSELN
- 37.11.36CH[7].CONFIG
- 37.11.37CH[7].LIMIT
- 37.11.39OVERSAMPLE
- 37.11.40SAMPLERATE
- 37.11.41RESULT.PTR
- 37.11.42RESULT.MAXCNT
- 37.11.43RESULT.AMOUNT
- 37.12Electrical specification
- 37.13Performance factors
- 38COMP — Comparator
- 39LPCOMP — Low power comparator
- 40WDT — Watchdog timer
- 41SWI — Software interrupts
- 42NFCT — Near field communication tag
- 42.1Overview
- 42.2Pin configuration
- 42.3EasyDMA
- 42.4Collision resolution
- 42.5Frame timing controller
- 42.6Frame assembler
- 42.7Frame disassembler
- 42.8Antenna interface
- 42.9NFCT antenna recommendations
- 42.10Battery protection
- 42.11References
- 42.12Registers
- Table 99: Instances
- 42.12.6FRAMESTATUS.RX
- 42.12.7CURRENTLOADCTRL
- 42.12.8FIELDPRESENT
- 42.12.9FRAMEDELAYMIN
- 42.12.10FRAMEDELAYMAX
- 42.12.11FRAMEDELAYMODE
- 42.12.12PACKETPTR
- 42.12.13MAXLEN
- 42.12.14TXD.FRAMECONFIG
- 42.12.15TXD.AMOUNT
- 42.12.16RXD.FRAMECONFIG
- 42.12.17RXD.AMOUNT
- 42.12.18NFCID1_LAST
- 42.12.19NFCID1_2ND_LAST
- 42.12.20NFCID1_3RD_LAST
- 42.12.21SENSRES
- 42.12.22SELRES
- 42.13Electrical specification
- 43PDM — Pulse density modulation interface
- 44I2S — Inter-IC sound interface
- 44.1Mode
- 44.2Transmitting and receiving
- 44.3Left right clock (LRCK)
- 44.4Serial clock (SCK)
- 44.5Master clock (MCK)
- 44.6Width, alignment and format
- 44.7EasyDMA
- 44.8Module operation
- 44.9Pin configuration
- 44.10Registers
- Table 108: Instances
- 44.10.7CONFIG.TXEN
- 44.10.8CONFIG.MCKEN
- 44.10.9CONFIG.MCKFREQ
- 44.10.10CONFIG.RATIO
- 44.10.11CONFIG.SWIDTH
- 44.10.12CONFIG.ALIGN
- 44.10.13CONFIG.FORMAT
- 44.10.14CONFIG.CHANNELS
- 44.10.15RXD.PTR
- 44.10.16TXD.PTR
- 44.10.17RXTXD.MAXCNT
- 44.10.18PSEL.MCK
- 44.10.20PSEL.LRCK
- 44.10.21PSEL.SDIN
- 44.10.22PSEL.SDOUT
- 44.11Electrical specification
- 45MWU — Memory watch unit
- Table 110: Memory regions
- 45.1Registers
- Table 111: Instances
- 45.1.4NMIEN
- 45.1.5NMIENSET
- 45.1.6NMIENCLR
- 45.1.7PERREGION[0].SUBSTATWA
- 45.1.8PERREGION[0].SUBSTATRA
- 45.1.9PERREGION[1].SUBSTATWA
- 45.1.10PERREGION[1].SUBSTATRA
- 45.1.12REGIONENSET
- 45.1.14REGION[0].START
- 45.1.15REGION[0].END
- 45.1.16REGION[1].START
- 45.1.17REGION[1].END
- 45.1.18REGION[2].START
- 45.1.19REGION[2].END
- 45.1.20REGION[3].START
- 45.1.21REGION[3].END
- 45.1.22PREGION[0].START
- 45.1.23PREGION[0].END
- 45.1.25PREGION[1].START
- 45.1.26PREGION[1].END
- 46EGU — Event generator unit
- 47PWM — Pulse width modulation
- 48SPI — Serial peripheral interface master
- 49TWI — I2C compatible two-wire interface
- 50UART — Universal asynchronous receiver/ transmitte
- 51Mechanical specifications
- 52Ordering information
- 53Reference circuitry
- 53.1Schematic QFAA and QFAB QFN48 with internal LDO se
- 53.2Schematic QFAA and QFAB QFN48 with DC/DC regulato
- 53.3Schematic QFAA and QFAB QFN48 with DC/DC regulato
- 53.4Schematic CIAA WLCSP with internal LDO setup
- 53.5Schematic CIAA WLCSP with DC/DC regulator setup
- 53.6Schematic CIAA WLCSP with DC/DC regulator and
- 53.7PCB guidelines
- 53.8PCB layout example
- 54Liability disclaimer
- Mouser Electronics
Contents
Page
5
32 SPIS — Serial peripheral interface slave with EasyDMA
..................................
292
32.1 Shared resources 292
32.2 EasyDMA 292
32.3 SPI slave operation 293
32.4 Pin configuration 294
32.5 Registers 295
32.6 Electrical specification 303
33 TWIM — I
2
C compatible two-wire interface master with EasyDMA.................305
33.1 Shared resources 306
33.2 EasyDMA 306
33.3 Master write sequence 307
33.4 Master read sequence 308
33.5 Master repeated start sequence 309
33.6 Low power 310
33.7 Master mode pin configuration 310
33.8 Registers 310
33.9 Electrical specification 317
34 TWIS — I
2
C compatible two-wire interface slave with EasyDMA
....................
319
34.1 Shared resources 321
34.2 EasyDMA 321
34.3 TWI slave responding to a read command
...............................................................................
321
34.4 TWI slave responding to a write command
..............................................................................
322
34.5 Master repeated start sequence 323
34.6 Terminating an ongoing TWI transaction
..................................................................................
324
34.7 Low power 324
34.8 Slave mode pin configuration 324
34.9 Registers 325
34.10 Electrical specification 331
35 UARTE — Universal asynchronous receiver/transmitter with EasyDMA
.....
333
35.1 Shared resources 333
35.2 EasyDMA 333
35.3 Transmission 334
35.4 Reception 334
35.5 Error conditions 336
35.6 Using the UARTE without flow control
......................................................................................
336
35.7 Parity configuration 336
35.8 Low power 336
35.9 Pin configuration 337
35.10 Registers 337
35.11 Electrical specification 345
36 QDEC — Quadrature decoder 347
36.1 Sampling and decoding 347
36.2 LED output 348
36.3 Debounce filters 348
36.4 Accumulators 349
36.5 Output/input pins 349
36.6 Pin configuration 349
36.7 Registers 350
36.8 Electrical specification 356
37 SAADC — Successive approximation analog-to-digital converter
.................
357
37.1 Shared resources 357
37.2 Overview 357
37.3 Digital output 358
37.4 Analog inputs and channels 359
37.5 Operation modes 359
37.6 EasyDMA 361
37.7 Resistor ladder 362