Installation Instructions

ManualsBrandsEcolink Intelligent Technology ManualsElectronicsLight Sensor

Table Of Contents

PN DWLZWAVE2.5-ECO R1

DWLZWAVE2.5-ECO

Door/Window Sensor Installation Instructions

Product Overview

• Z-Wave+™ enabled device which provides open/closed position status

• Transmits open/closed status

• Reports tamper condition when cover is open

• Product Specifications

• For indoor use only

• Operating Frequencies: 908.42 and 916 MHz

• Operation range: Up to 100 feet (30.5 meters) line-of-sight

• Operating temperature: 0° – 49°C, 32° – 120°F (ambient temperature)

• Battery type required: 3V Lithium CR123A

• Battery life approximately 3 years

Netwo

rk Inclusion

The sensor must be added to a Z-Wave network prior to use. To include the sensor in a network

both the sensor and the network controller must be in inclusion mode at the same time. Refer to

the instructions provided by the manufacturer of your specific controller for details on initiating

the controller’s inclusion mode.

1) Verify that the Z-Wave Plus controller you are using is compatible with the Light Sensor.

2) Either mount or move the Light Sensor as close as possible to the location the sensor will remain. See installation section below.

3) Put your Z-Wave Plus Controller into add (inclusion) mode.

4) To add the sensor to an existing Z-Wave network, follow the directions to put your Z-Wave Controller into add (inclusion) mode. Activate inclusion mode

for the sensor by removing the plastic pull-tab from the back of the sensor. When the inclusion process in complete, the LED on the sensor will be solid

blue, then go out.

5) Test the sensor. With the light sensor top cover closed, cover and uncover the phototransistor. If the LED flashes ONE TIME, it is successfully

communicating on your Zwave network. If the LED on the sensor flashes slow and steady for 5 seconds, you need to repeat the inclusion process.

Summary of content (8 pages)

PAGE 1
DWLZWAVE2.5-ECO Door/Window Sensor Installation Instructions • • • Product Overview Z-Wave+™ enabled device which provides open/closed position status Transmits open/closed status Reports tamper condition when cover is open • • • • • • • Product Specifications For indoor use only Operating Frequencies: 908.42 and 916 MHz Operation range: Up to 100 feet (30.
PAGE 2
Network Inclusion: Key Points to Remember • Controller inclusion mode must be activated BEFORE starting sensor inclusion mode. • The sensor can only be included into one controller network at a time, and must be excluded from one network before inclusion in another. • Removing the pull tab connects the battery and initiates sensor inclusion mode. Inclusion mode can also be initiated by removing the battery for at least 5 seconds, reinstalling the battery, then replacing the sensor cover.
PAGE 3
ADDITIONAL NOTES AND SUMMARY: • With either mounting method the first step is to attach the sensor mounting bracket to the mounting surface. (The mounting bracket is used regardless of choice of screws or tape). • The sensor can slide onto the mounting bracket in two different ways. To ensure that the sensor is securely fastened it is recommended that the tab on the bracket engage the back of the sensor.
PAGE 4
Factory Default To restore this sensor to factory default settings, follow the instructions in this manual to exclude this sensor from the Z-Wave network. Upon completion of removal from the network the sensor will restore itself to factory default settings automatically. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.
PAGE 5
CONDITION SENSOR COMMAND CLASS and VALUE Notification Report of Access Control (0x06), Door/Window is open (0x16) Door/Window Open Sensor Binary Report of 0xFF Sensor Type: 0xFF Basic set of 0xFF (On) Notification Report of Access Control (0x06), Door/Window is closed (0x17) Door/Window Close Sensor Binary Report of 0x00 Sensor Type: 0xFF Basic Set of 0x00 (Off) By factory default this feature is disabled and must be enabled via Configuration Command Class.
PAGE 6
Wake-Up Notification The sensor will wake up every so often and when the case is closed to send a Wake-Up Notification to allow the life line master node controller that the sensor is now available for any queued messages that the controller may have for the sensor. The time between Wake-Up Notifications can be configured with the WakeUp Notification command class to be between 1 hour and 1 week with interval steps of 200 seconds. Configuration The sensor has two configuration parameters.
PAGE 7
FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules.
PAGE 8
By the act of use, setup or assembly of the product, you accept all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the product, you are advised to return the product immediately in new and unused condition to the place of purchase. Some states do not allow the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. RETURN POLICY Please visit us at www.discoverecolink.