User's Manual

ManualsBrandsEcolink Intelligent Technology ManualsElectronicsZ-Wave Plus Flood Freeze Sensor with a Probe

Z-Wave Plus Flood/Freeze Sensor Installation Instructions

Product Overview

 Z-Wave+™ enabled device which detects flood and freeze.

 Reports tamper condition when cover is open

Product Specifications

 For indoor use only

 Operating frequency: 908.42 MHz

 Operating temperature: 0° – 49°C, 32° – 120°F (ambient temperature)

 Operating humidity 5-95% non-condensing

 Battery type required: 3V Lithium CR123A

 Battery life approximately 5 years

Network Inclusion

The sensor must be added to a Z-Wave network prior to use. To include the sensor in a network both the sensor and the network controller must be in inclusion mode

at the same time. Refer to the instructions provided by the manufacturer of your specific controller for details on initiating the controller’s inclusion mode.

1) Verify that the Z-wave Plus controller you are using is compatible with the Flood Freeze sensor.

2) Either mount or move the Flood Freeze sensor as close as possible to the location the sensor will remain. See installation section below.

3) Put your Z-wave Plus Controller into add (inclusion) mode.

4) To add the sensor to an existing Z-Wave network, follow the directions to put your Z-Wave Controller into add (inclusion) mode. The Flood Freeze enters add

and remove (inclusion/exclusion) when powered on (when battery is added). If the LED starts blinking continuously, the sensor has no node ID and was not

successfully added, so start step C over again. Make sure to remove the battery for 10 seconds if adding to a z-wave network fails.

5) If after 5 seconds the LED is not blinking, look on the Z-Wave controller’s interface for feedback on whether the sensor was added successfully. If you do not

see any feedback that the sensor was added, follow directions for removing the sensor from a Z-Wave network, and then try adding the sensor again. If you

are still having problems, you may need to add additional Z-Wave listening devices in-between the controller and the sensor.

Network Exclusion

1) Any sensor can be removed from any Z-Wave Plus controller. Follow the directions to put your Z-Wave Plus Controller into exclusion mode.

2) Open the Flood Freeze case and remove the battery for 1 seconds. Replace the battery and the controller should remove the device from the Z-Wave

network.

Network Inclusion/Exclusion: Key Points to Remember

 Controller inclusion/exclusion mode must be activated BEFORE starting sensor inclusion or exclusion mode.

 The sensor can only be included into one controller network at a time, and must be excluded from one network before inclusion in another.

 The plastic pull tab must be removed to enable sensor operation.

 The sensor automatically enters inclusion mode at power-up.

 Exclusion mode on the senor is initiated following the same exact procedure as inclusion.

Summary of content (9 pages)

PAGE 1
Z-Wave Plus Flood/Freeze Sensor Installation Instructions Product Overview   Z-Wave+™ enabled device which detects flood and freeze. Reports tamper condition when cover is open Product Specifications       For indoor use only Operating frequency: 908.
PAGE 2
LED Status The Flood Freeze is equipped with a single LED. The state of the LED will change based on the state of the device. Device not included Flood Detected Freeze Detected Case Opened = Light breathing (slow blink) = Single LED blink = Single LED blink = LED will remain on while case open Factory Default The Flood Freeze sensor factory defaults on network exclusion. Testing To test the RF transmission from the mounted position you can generate a tamper by removing the cover.
PAGE 3
STEP ONE STEP TWO Identify Location for Sensor: Determine where to place the probe sensor. The probe should be located where water is most likley to pool if a leak occurs. The sensor needs to be mounted while the probe can reach the location described above. Mount the Sensor: Mount the sensor to a clean dry surface with the adheasive tape and/or the screws provided Adhesive Tape © 2017 Ecolink Intelligent Technology Inc.
PAGE 4
STEP THREE Mount the Probe: Mount the probe to a clean dry surface where water is most likley to pool if a leak occurs. ADDITIONAL NOTES AND SUMMARY:    The sensor can slide onto the mounting bracket in two different ways. To ensure that the sensor is securely fastened it is recommended that the tab on the bracket engage the back of the sensor. Before attaching the bracket to a surface note how the bracket will need to be oriented in order for the tab to engage the sensor.
PAGE 5
Z-Wave Plus Specific Information Z-Wave Plus is a wireless mesh network and data protocol that allows devices from many different manufacturers to interoperate. This device implements Z-Wave Plus functionality, Network Wide Inclusion, and Explorer frames. This device is asleep most of the time but can respond to queries on a Wake Up Notification; however for test purposes, the device will stay awake while tampered for testing Z-Wave Plus command class functionality.
PAGE 6
Z-Wave Plus Command Class Notification These notifications are sent unsolicited to the lifeline Association group.
PAGE 7
Z-Wave Plus Command Class Sensor Binary These notifications are sent unsolicited to the lifeline Association group. Notification Type Water (0x06) Freeze (0x07) © 2017 Ecolink Intelligent Technology Inc.
PAGE 8
Z-Wave Plus Command Class Association The Flood Freeze sensor supports one association group with up to 5 nodes. All notifications, and events are sent to association group one (lifeline). Association This sensor has one Association groups of 5 nodes. Group one is a lifeline group who will receive unsolicited messages relating to flood/freeze notifications, case tampering notifications, low-battery notifications.
PAGE 9
LIMITED WARRANTY This limited warranty is provided by Ecolink Intelligent Technology (“Ecolink”) to you as the original purchaser of the product. Ecolink warrants this product to be free from defects in material and workmanship for a period of one (1) year from the date of original purchase. The determination of whether the product is defective shall be made by Ecolink in its sole discretion with consideration given to the overall performance of the product.