Cloud Master Jr. Manual ECOLUMINA TECHNOLOGIES, Inc. 6F.-5, No.432, Sec. 1, Keelung Rd Xinyi Dist.
Cloud Master Jr Setup Manual © 2018 by ECOLUMINA TECHNOLOGIES, Inc. All rights reserved. Trademarks Ecolumina is a trademark of ECOLUMINA TECHNOLOGIES, Inc. Other brand and product names are registered trademarks or trademarks of their respective holders.
Cloud Master Jr Setup Manual Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Cloud Master Jr Setup Manual About About Ecolumina About this product Features 4 4 4 4 Introduction In the box Front view LED status Back view 5 5 5 6 6 Installation Power Network Setup 7 7 7 8 DashBoard Dashboard device status 9 9 Connecting with NVR 10 Connecting with devices IoT devices management 11 11 Trigger setting 12 Firmware upgrade Backup System Configuration System Upgrade Restore System Configuration 13 13 13 13 Troubleshooting Troubleshooting from the LED indicator Advanced Tro
Cloud Master Jr Setup Manual About About Ecolumina Ecolumina Technologies Inc., focusing on customer orientation and excelling in research & development, is a pioneering technology company devoted to Edge Computing IoT integration and application, and endeavored to achieve 100% quality and 100% satisfaction for our customers.
Cloud Master Jr Setup Manual Introduction In the box In the box contains ● An adapter ● Internet wire ● Cloud Master Jr.
Cloud Master Jr Setup Manual LED status LED Status Description Application On WiFi Zigbee Connected with NVR Blink Error connecting with NVR, please reboot devices.
Cloud Master Jr Setup Manual Installation Power Connect the power cord to the device. Network Connect to network by using RJ-45 connector. Note: Please connect to internet to make sure system runs correctly. Note: Cloud Master Jr. should be configured as STATIC IP.
Cloud Master Jr Setup Manual Setup 1. Connect to the Cloud Master Jr. using your laptop or smart phone’s WiFi. 2. Default SSID is CMJUNIOR_XXXXXX (XXXXXX is the products MAC address last 6 digit) and the default password is 1234567890. 3. Open browser and connect to the following IP: http://192.168.23.1/ 4.
Cloud Master Jr Setup Manual DashBoard Dashboard device status Status Description Green Device online in last hour Orange Device have not been online for over an hour Red Device have not been online for over a day 10
Cloud Master Jr Setup Manual Connecting with NVR NOTE:Make sure Cloud Master Jr. and NVR are in the same subnet. NOTE:NVR and ip-cam registered in NVR should be configured as STATIC IP. NOTE:NVR SHOULD enable ALARM configuration. NOTE:Only remove NVR when you have physical access with NVR 1. Go to device configuration. 2. Go to NVR devices. 3. Press the add button on the bottom left page.
Cloud Master Jr Setup Manual Connecting with devices IoT devices management 1. Press the round button on the Cloud Master Jr. to allow devices to join network for 60 seconds. 2. Make sure your IoT devices are powered on to join the network automatically. 3. You can check if the devices are joined in the Device Configuration page. 4. After the IoT devices are joined in the network, go to Device Configuration, Device management and edit the device name.
Cloud Master Jr Setup Manual Trigger setting Trigger setting example of a siren 1. Go to device configuration. 2. Go to trigger configuration. 3. Press the add button at left bottom page.
Cloud Master Jr Setup Manual Trigger setting example of canceling a delay trigger If a trigger is in delay, it can be cancel by other trigger. For example we can set a new trigger to cancel the previous trigger above.
Cloud Master Jr Setup Manual Firmware upgrade NOTE:System backup is strongly recommended before upgrade. NOTE:Reboot before upgrading firmware. Backup System Configuration 1. Press the Backup button, Cloud Master Jr. will automatically generate a backup file and will start the download in few seconds. System Upgrade 1. Download the latest firmware. 2. Press the Choose file button, choose the upgrade bin file. 3. Press the System Upgrade button to start the upgrade process.
Cloud Master Jr Setup Manual Troubleshooting Troubleshooting from the LED indicator If the LED indicator are all off, make sure the power cord is connected to Cloud Master Jr. The Application LED indication • Application is in Running state, The led will always be turned ON. • Application is in Read state, The led will be blinking every 500ms. • Application is in Not Ready state, The led will be turned OFF. The WiFi LED indication • When the Cloud Master Jr. in AP mode and enable.
Cloud Master Jr Setup Manual Troubleshooting when upgrading firmware If firmware upgrade fail, try reboot before upgrade. Restoring the Default Configuration and Password Use a sharp object like a pen or a paper clip to press and hold the default reset button for about 10 seconds. It will change the Cloud Master Jr’s administration password to admin and the IP address to 192.168.23.1. You can erase the current configuration and restore factory defaults.
