Produktbereich Portable Handlampen Lite-Ex PL 10 Operating Instructions LED 0 1 2 3 4 5 6 7 kg Zone 0/20 3.
Table of Contens 1. 2. 3. 4. 4.1 5. 6. 7. 8. 8.1 8.2 8.3 8.4 8.5 8.6 8.7 9. 10. 11. 12. 13. 14.
1. Application The Lite-Ex PL 10 is a compact, robust and easy-to-use LED flashlight for industrial application in Ex-hazardous areas classified as Zone 2, 1 and 0, as well as Zone 22, 21 and 20, in accordance with directive 1999/92/EC (ATEX 137). 2. Safety precautions These operating instructions contain information and safety regulations which are to be observed without fail for safe operation in the described conditions.
- unit markings or inscriptions are illegible. - malfunctions occur. - permitted limit values have been exceeded. 4. Safety regulations Use of this unit assumes that the operator observes the conventional safety regulations and has read the certificate in order to eliminate faulty operation of the unit. The following safety regulations must also be complied with: -T he unit should not be opened inside the Exarea. -T he batteries may only be exchanged outside the Ex-area.
. Safety precautions Risk of blinding! - Do not look directly into the light beam - Do not aim the light directly into the eyes of another person 6. Ex-Data EC type approval test certificate no.: ZELM 05 ATEX 0272 X Ex-designation: II 1G Ex ia op is IIC T4 Ga II 1D Ex ia IIIC T130 °C Da Approved for Zone 2, 1 and 0, Device of the group II, gas group C (explosive gases, vapours or mist), temperature class T4.
7. Technical specifications Ambient temperature Ta: -20 °C ... +50 °C Storage temperature: -30 °C ... +60 °C Batteries / power supply: 3 x LR03 according to IEC, AAA Lamp: High performance LED: 3000 lx Operating time: 1200 lx after 3 hours, approx. 150 lx after 6 hours (at a distance of 1 m) Dimensions: 147 x 36 x 36 mm Weight: approx.
8. Functional description / operating instructions Please read these operating instructions carefully so that you are familiar with, and are able to use, all of the functions of your Lite-Ex PL 10. For your own safety and information please read the instructions on the following pages carefully! 8.1 Assembly of the Lite-Ex PL 10 Thread-forming screw for plastic 20 x 10 T6 Belt clip Flashlight body Lamp head Disc Ring switch Sealing ring 22.8 x 1.5 LED housing Sealing ring 22.76 x 2 Fig. 1 8.
.3 Battery replacement The batteries should be replaced if the level of luminance is no longer deemed to be satisfactory. It is advisable to change all 3 batteries at the same time. Only the appropriate, approved types of batteries may be used (refer to the table with details of the type-tested batteries under point 7: Technical specifications). To replace the batteries grasp the lamp head firmly, twist the body of the flashlight (incl. ring switch) anticlockwise and then remove it.
can now be removed and cleaned. When it has been cleaned replace the ring switch and rotate it until it engages firmly in place (magnet must be positioned on the shaft - ecom address side). The lamp head can then be screwed back onto the flashlight. 8.5 LED replacement The Lite-Ex PL 10 is equipped with a long-life LED bulb. Under normal conditions it is not necessary to change the LED.
ring is set in a groove under the protective disc). When replacing the lamp head on the LED housing make sure the seal and disc are seated properly. After assembly no part of the seal should be visible through the opening where the beam is emitted. If the LED housing or lens has been damaged, the flashlight should be sent to the manufacturer for repair. (Fig. 2) 8.
9. Repair Repairs are to be conducted by ecom instruments GmbH or by personnel or service centres authorised by ecom instruments GmbH, because the safety of the unit needs to be tested after repairs are implemented. 10. Disposal Old electrical devices as well as „historical“ old electrical devices from ecom instruments GmbH are supplied for disposal at our expense and disposed of free of charge in accordance with European Directive 2002/96/EC and the German electrical law of 16/03/2005.
hazard and can cause chemical injuries if it is used improperly. Neither the battery nor the battery cells should be opened or disassembled and they should not be burned or exposed to temperatures exceeding 100 °C. If the battery needs to be disposed of, it can be removed as described under point 8.3. The disposal regulations specified above are also applicable for old devices. All batteries can be recycled. Precious raw materials such as iron, zinc and nickel can therefore be reused.
12. Warranty and liability In accordance with our general terms and conditions ecom instruments GmbHprovides a warranty for this product for a period of two years regarding its function and material under the specified and permitted operating and maintenance conditions. This excludes all parts that are subject to wear and tear (e.g. batteries, probes, calibration units, LEDs, etc.).
tioned limitations and exclusions are not valid for every purchaser. Should any such clause of these warranty conditions be declared ineffective or unenforceable by a competent court, then the effectiveness or enforceability of any of the other conditions of these warranty conditions shall remain unaffected by such a judgement.
13.
14. EC-Type Examination Certificate 1) T he following special conditions according to the EC type approval test certificate must be observed: Opening the housing within the explosive area is not permitted. 1. The installed batteries may only be exchanged outside the explosive area and only by those types approved by the manufacturer. 2. A visual and functional inspection should be conducted at regular intervals to ensure an orderly external condition of the flashlight.
Product devision Porable Lighting Copyright© 2010 ecom instruments GmbH. Der Inhalt dieses Dokuments darf ohne vorherige schriftliche Genehmigung durch die ecom instruments GmbH in keiner Form, weder ganz noch teilweise vervielfältigt, weitergegeben, verbreitet oder gespeichert werden. Der Inhalt dieses Dokuments wird so präsentiert, wie er aktuell vorliegt.