Product Manual

ManualsBrandsEcoMaster ManualsAutomotive45-Gallon Aqueous Industrial Parts Washer

04379 Page 1 11-01-12

ECN 3783

INDUSTRIAL - AQUEOUS PARTS CLEANER

EM6000

I. Introduction

A. Manufacturer’s Statement

This manual will provide you with important information about the Aqueous Parts Cleaners and will

instruct you on how to use this equipment in a safe manner.

The information contained in this manual is necessary for the safe, proper setup and operation of

your Aqueous Parts Cleaner.

Keep this manual, along with the Material Safety Data Sheets (MSDS) for the solution in use, within

easy reach of the operator of this parts cleaner.

The equipment described in this manual is subject to change. The manufacturer reserves the right to

change equipment at any time as part of normal product improvement. Some improvements may

have been made after this manual was printed. For the latest information on your equipment, contact

the manufacturer.

B. General Information

CAUTION

READ AND UNDERSTAND ALL LABELS, MSDS, AND

THIS INSTRUCTION MANUAL BEFORE USE.

The Industrial Aqueous Parts Cleaner is an economical, safe, and innovative system designed to

clean parts, using an aqueous based solution. Aqueous solutions, when used to clean grease and oil,

must be disposed of properly. Consult your local environmental management agency for additional

guidance and other potentially hazardous materials compliance requirements.

Install your parts cleaner on a flat, level surface in an area provided with adequate ventilation. Avoid

repeated or prolonged breathing of vapors. Do

NOT

use compressed air to dry parts as this may

cause a high concentration of vapors in the immediate area. Local exhaust ventilation should be used

in areas of high vapor concentration. Provisions for determining and maintaining adequate ventilation

are the responsibility of the operator.

Make sure the parts cleaner is connected to a properly grounded power source. Check serial plate for

power requirements.

NOT

allow the parts cleaner to operate unattended.

OPERATION & INSTRUCTION MANUAL

Summary of content (11 pages)

PAGE 1
INDUSTRIAL - AQUEOUS PARTS CLEANER OPERATION & INSTRUCTION MANUAL EM6000 I. Introduction A. Manufacturer’s Statement This manual will provide you with important information about the Aqueous Parts Cleaners and will instruct you on how to use this equipment in a safe manner. The information contained in this manual is necessary for the safe, proper setup and operation of your Aqueous Parts Cleaner.
PAGE 2
II. Safety Instructions and Information Complete safety in use is dependent upon proper use and handling of the parts cleaner in your workplace. It is important that you follow the instructions provided in this manual. If you fail to read, understand, and follow all of the procedures in this manual, you may cause or suffer personal injury. DO NOT OPERATE ELECTRICAL EQUIPMENT INSIDE OF PARTS CLEANER.
PAGE 3
A. Important Safety Instructions 1. Read all instructions. 2. Care must be taken as burns can occur from touching hot parts. 3. Do not operate equipment with a damaged cord or if the equipment has been dropped or damaged – until it has been examined by a qualified service person. 4. If an extension cord is necessary, a cord with a current rating equal to or more than that of the equipment should be used. Cords rated for less current than the equipment may overheat.
PAGE 4
B. Service Call your representative should your parts cleaner need service and always unplug unit when servicing. Inspect and keep in good working order the power cord and all electrical components. If components show signs of damage or wear replace immediately. All work should be done by a trained technician. Do NOT replace pump before unplugging unit and letting it completely cool down. Do NOT replace fusible link with any other device to hold lid up.
PAGE 5
3. INHALATION (Breathing): Prolonged exposure to concentrate-mist or vapor may cause mild irritation of nasal passages or throat. Remove to fresh air immediately. Do not leave victim unattended. Get medical attention if irritation persists. 4. INGESTION (Swallowing): (Uncontaminated cleaning solution) Drink 4 to 8 ounces of water and seek medical attention. DO NOT induce vomiting. E. Environmental 1. Avoid spilling solution. Spilled solution can create slippery conditions, clean it up immediately.
PAGE 6
IV. Operation This unit has an automatic low-fluid control sensor. Unit operates on 40-45 gallons (151.4-170.3 L.) or more of fluid. When the fluid level decreases to 35 gallons (132.5 L.), pump will shut off. When this occurs, add 5-7 gallons (18.9-26.5 L.) of fluid to machine to reset low fluid control sensor. This will reactivate the pump. Thermostat is “PRESET” do NOT adjust. Higher temperature could cause damage to skin. A. Fluid Control Valves There are two valves used for controlling fluid flow.
PAGE 7
V. Cleaning 1. Turn OFF heater and pump, let cool. 2. Lift basin out of reservoir and set on top of reservoir. 3. Disconnect the cam coupler on the hose and place the basin on the ground. 4. Place hose from the pump over the side of the reservoir and into the container being used to hold the waste fluid. 5. Turn ON the pump and pump the fluid level down to the point where the pump quits pumping. 6. Evacuate the balance of the fluid in the bottom of the reservoir. 7.
PAGE 8
04379 Page 8 11-01-12 ECN 3783
PAGE 9
Fluid Flow 04379 Page 9 11-01-12 ECN 3783
PAGE 10
VII. TROUBLESHOOTING A. Machine does not operate: 1. Make sure the parts cleaner is connected to electric power or air supply. 2. Check for incoming power. Check serial plate for power requirements. 3. On electric units: check reset button on GFCI cord to make sure it is not tripped. On air units: an increase in air supply may be required. B. Cleaning fluid not to temperature: 1. Check to make sure heater switch is turned “ON”. 2. Check fluid level in tank. 3.
PAGE 11
Warranty and Limitation of Remedies and Disclaimer LIMITED WARRANTY AND LIMITATION OF REMEDIES AND DISCLAIMER. (1)Fountain Industries “Fountain” warrants the Equipment to be free from defects in material and manufacture and to conform to specifications for the Equipment at the time of shipment. This warranty is applicable only if the Equipment is installed, operated and maintained in accordance with factory recommendations and procedures.