Owner's manual

Installation Instructions
TOOLS REQUIRED:
= Safety Glasses
= Drill & drill bit (only needed if existing hole is not available)
= Adjustable wrench
A. PREPARE MOUNTING HOLE
1. Select one of the following places for the faucet. Be sure it will fit
flat against the surface, and there is space underneath for tubes.
= Use an existing sink top hole for a spray hose or other
faucet. A 1-1/4" diameter hole is needed.
= Drill a new hole in the countertop next to the sink.
= Drill a new hole in the sink top.
IMPORTANT: Drilling holes into countertops made of stone
or solid surface materials such as granite, marble, Corian™
or other plastic resin products or sinks made of porcelain and
stainless steel should only be performed by a qualified installer
who is certified for drilling such materials. Drilling of these
type surfaces by any other means may cause permanent,
irreparable damage to the countertop surface.
2. If drilling is needed, make the 1-1/4" diameter hole.
B. ASSEMBLE FAUCET
If using this faucet with an existing Drinking Water system, fol-
low manufacturer’s installation instructions.
1. Remove the nut from the end of the stud. Slide the spacer
and lock washer on the stud. Place the nut back on the stud.
2. Work tubing and the faucet stud down, into the mounting hole.
3. On the underside of the sink or countertop, slide the slotted
washer between the countertop and spacer. Tighten the hex
nut securely.
4. Thread the 3/8" quick connect adaptor onto the end of the
stud and tighten securely.
5. Connect 3/8” water line from filtration system by pushing line
into 3/8” quick connect adaptor.
6. If a drain line is required to run through the faucet for a reverse
osmosis (RO) system, connect the 1/4” drain line from the
unit to the smaller barb on the bottom of the faucet. Connect
the 3/8” line from the faucet to the drain. This drain line works
by gravity. Make it as short and straight as possible, with no
dips or loops.
Questions? Call Ecodyne at 1-800-693-1138
7325736 (Rev. D 9/20/12)
Limited Warranty
Ecodyne Water Systems Faucet
Ecodyne Water Systems warrants its products to the original owner and guarantees that the faucet will be free from defects in materials and work-
manship for a period of 90 days from the date of installation.
To obtain warranty service, send the part with a copy of your sales receipt to: Ecodyne Water Systems
Attn: Warranty
1890 Woodlane Drive
Woodbury, MN 55125
This warranty does not include normal shipping, installation or service charges.
There are no warranties on the faucet, beyond those specifically described above. All implied warranties, including any implied warranty of mer-
chantability or of fitness for a particular purpose, are disclaimed to the extent they might extend beyond the above periods. The sole obligation of
Ecodyne Water Systems under this warranty is to replace or repair the component or part, which proves to be defective within the specified time peri-
od and Ecodyne is not liable for consequential or incidental damages. No authorization is given to extend or expand the warranty expressly described
above. This warranty gives you specific, legal rights, and you may have other rights, which vary from state to state.
Faucet
1/4” Barb /
Boquilla de
1/4 pulg. /
Raccord
cannelé
de 6,3 mm
(1/4 po)
IN from R.O.
System /
Entrada del
sistema de
ósmosis
inversa /
Entrée du
système
d’osmose
inversée
Spacer /
Separador /
Cale
d’espacement
Stud /
Espárrago /
Tige
Nut /
Tuerca /
Écrou
3/8” Quick
Connect Adaptor /
Adaptador de
conexión rápida
de 3/8 pulg. /
Adaptateur de
raccord rapide de
9,5 mm (3/8 po)
Faucet /
Grifo /
Robinet
Base
Countertop /
Encrimera /
Revêtement
de comptoir
3/8” Barb /
Boquilla de 3/8 pulg. /
Raccord cannelé de
9,5 mm (3/8 po)
OUT to drain /
Salida a desagüe /
Sortie à drain
Slotted Washer /
Arandela ranurada /
Rondelle fendue
Lock Washer /
Arandela de seguridad /
Rondelle de blocage
3/8” water line from filtration system /
Tubo de agua de 3/8 pulg. del sistema
de filtrado /
Canalisation d’eau de 9,5 mm (3/8 po)
du système de filtration
(Only used if air gap is needed
for reverse osmosis systems) /
(Sólo se usa si se necesita una toma de aire
para sistemas de ósmosis inversa) /
(Seulement utilisé si un espace d’air est néces-
saire pour les systèmes d’osmose inversée)
Rubber
O-ring /
Junta del
caucho /
Joint en
caoutchouc