MP60w ES ® 11 0113 Setup Guide
Customer Support Congratulations on your purchase of a VorTech™ MP60 Propeller Pump! Many of the steps in this guide have corresponding how-to videos. View them on the EcoTech Marine website at ecotechmarine.com/media-gallery/video . The EcoTech Marine Community is another tool for users to troubleshoot and learn about our products. For additional information about your VorTech Propeller Pump, please visit us at community.ecotechmarine.
Inside the Box POWER SUPPLY POWER CORD Maintenance FOAM GUARD Your VorTech Propeller Pump is designed to operate optimally with little attention after initial setup; however, due to the harsh conditions of a saltwater aquarium and resulting buildup of algae and other organic matter, it is advisable to clean your wet side to ensure the longevity of your purchase. EcoTech recommends doing a wet side cleaning every 6 to 8 weeks or as necessary.
Installing the VorTech™ STEP 1: Choose Pump Location • Where the pump output is unobstructed • High enough above the sand bed so sand is not disturbed • Sufficiently below the surface so air is not sucked into a vortex STEP 2: Prepare Aquarium • Use an aquarium scraper to clean the inside surface of the aquarium and a damp cloth to clean the outside. • Use caution when handling an aquarium scraper.
Installing the VorTech™ Continued STEP 6: Attach Wet Side • Place the wet side into the aquarium and allow ALL air to escape from the propeller housing. • Carefully align the wet and dry sides through the glass (Figures G). • Optional: Place the foam guard over the wet side of the pump. The foam guard can be used to ensure that delicate marine animals do not get caught in the nozzle. STEP 7: Align Pump • Plug the power supply into the driver.
The EcoSmar t Driver TM Wireless Indicator SET Button Mounting the Driver 1. Plug the power supply into the driver and then plug the power cord into the outlet (Figure A). The driver will turn on and be in Constant Speed Mode by default (green control dial). LED Strip MODE Button OPTION/Power Button Control Dial Battery Backup Input Pump Cable Slot Power Input USING EcoSmart 8 TM WATCH THE VIDEO: ecote.ch/ecosmartmodes Figure A 2.
EcoSmar t Driver Operational Modes TM (Hold) – Feed Mode 10 (Hold) – Power Off * LED bar will indicate change between modes.
Tidal Swell Mode Nutrient Transport Mode Tidal Swell Mode (TSM) creates a harmonic balance reminiscent of the changing flow conditions found in nature. Over the course of several hours, the flow pattern will go from very chaotic to calm, followed by a detritus-clearing surge at the very end of the cycle. The flow direction will change direction every cycle. The control dial is used to set the maximum pump speed during this mode.
Short Pulse Mode When first entering Short Pulse Mode, set the maximum pump speed with the control dial and press the SET button to lock it. The LEDs will begin to ramp, indicating the pulsing frequency between 0.2 seconds and 2 seconds. Next, use the control dial to adjust the pulse frequency. Press and hold SET until the control dial flashes and then breathes blue, indicating the wave is saved.
Reef Crest Random Mode Reef Crest Random Mode simulates a high-energy reef environment. It is indicated by both a yellow control dial and the first two blue LEDs illuminated. The control dial is used to set the maximum pump speed during this mode. The pump will change speed frequently and drastically to simulate crashing waves and surging tide. Additional Modes All modes are set to default duration, speed or percentage of speed. Refer to the full manual to learn how to customize these modes.
Troubleshooting In the event of a problem: 1. Check that the pump is plugged in and there is power. 2. U nplug the pump and check the wet side for damage or obstructions. 3. Reconnect the power and reset the driver (video: ecote.ch/resetdriver). 4. I f the pump still does not function properly, use one of these support methods: • Watch our extensive collection of how-to videos. These videos are available at ecotechmarine.
Regulatory Information • This product carries an ingress protection rating of IPX0 and must not be immersed in water. • Danger: To avoid possible electrical shock, special care should be taken since water is employed in the use of aquarium equipment. • DO NOT attempt repairs yourself; return the appliance to the manufacturer for service or discard. • DO NOT immerse in water. If the appliance falls into the water, DON’T reach for it! First unplug it and then retrieve it.