EN Instruction Manual
Congratulations on the purchase of your ECOVACS ROBOTICS DEEBOT! We hope it brings you many years of satisfaction. We trust the purchase of your new robot will help keep your home clean and provide you more quality time to do other things. Live Smart. Enjoy Life. Should you encounter situations that have not been properly addressed in this Instruction Manual, please contact our Customer Service Center where a technician can address your specific problem or question.
Contents 1. Important Safety Instructions........................................................................................................2 2. Package Contents and Technical Specifications......................................................................5 2.1 Package Contents.......................................................................................................................5 2.2 Specifications......................................................................................
1. Important Safety Instructions When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. SAVE THESE INSTRUCTIONS 1.
1. Important Safety Instructions 14. Do not use Appliance on wet surfaces or surfaces with standing water. 15. Do not allow the Appliance to pick up large objects like stones, large pieces of paper or any item that may clog the Appliance. 16. Do not use Appliance to pick up flammable or combustible materials such as gasoline, printer or copier toner, or use in areas where they may be present. 17.
1. Important Safety Instructions 31. The battery must be removed from the appliance before it is scrapped. 32. The appliance must be disconnected from the supply mains when removing the battery. 33. WARNING: For the purposes of recharging the battery, only use the detachable supply unit GSCV0600S019V12E provided with this Appliance. 34. The robot contains batteries that are only replaceable by skilled persons. 35. The Remote Control pre-installs two non-rechargeable AAA R03 batteries.
2. Package Contents and Technical Specifications 2.1 Package Contents AM PM AM PM MAX Robot Remote Control with Batteries Charging Dock with Power Adapter Cleaning Tool Instruction Manual High Efficiency Filter (4) Side Brushes (2 pre-installed, 2 replacements) 2.2 Specifications Model DM82 Working Voltage 14.8V DC Lithium battery UR18650ZT4S1P-AAF Battery Model Rated Power 22W Battery Specification Lithium 14.8V 2600mAh Charging Dock Rated Input Voltage 19V DC Rated Output Current 0.
2. Package Contents and Technical Specifications 2.3 Product Diagram Robot 13 8 1 9 10 4 2 5 6 11 7 12 3 1. Anti-Collision Sensors 2. AUTO Mode Button 3. Dust Bin Release Button 4. Charging Contacts 5. Battery Cover 6. Driving Wheels 7. Side Power Switch 8. Anti-Drop Sensors 9. Universal Wheel 10. Side Brushes 11. Main Brush 12. Dust Bin 13. Infrared Receiver for Remote Control Charging Dock 1 2 3 4 6 EN 1. Power Indicator Light 2. Power Adapter 3. Power Adapter Port 4.
2. Package Contents and Technical Specifications Remote Control 11 2 1 AM PM AM PM 4 3 6 MAX 5 7 8 10 9 1. Current Time Display 2. Scheduled Cleaning Time Display 3. Direction Control Buttons 4. START/PAUSE Button 5. Time Scheduling Button 6. MAX Button Press to: Adjust current time and scheduled cleaning time. Turn the robot around 180 degrees. Increase suction power for deep cleaning. 7. Spot Cleaning Mode Button 8. Set Current Time Button 9. Return to Charger Mode Button 10.
3. Operating and Programming 3.1 Notes Before Cleaning Before operating DEEBOT, take a few moments to survey the area to be cleaned and remove any obstacles. Remove power cords and small objects from the floor that could entangle the product. The product is not suitable for use on long-pile carpet. Before using the product near an area rug or on a short-pile area rug with tasseled edges, please fold area rug edges under themselves.
3. Operating and Programming 3.2 Quick Start 1 Charging Dock Placement Connect the Power Adapter to the Charging Dock. Place the Charging Dock on a level floor surface against the wall with the base perpendicular to the ground. Keep the immediate area 2m (6.6’) in front of the charger and 1 m (3.3’) on both sides of the charger clear of objects and reflective surfaces. Plug the Charging Dock in. 2 Power ON Turn the robot’s Side Power Switch to the ON position. “l” indicates ON and “O” indicates OFF.
3. Operating and Programming 4 Start Press the AUTO Mode Button on DM82 or the START/PAUSE Button on the Remote Control.. DM82 starts to work immediately in AUTO Cleaning Mode. AM PM AM PM MAX ** To choose another Cleaning Mode, please refer to section 3.3 Cleaning Mode Selection for details. 5 Pause Pause DM82 by pressing the AUTO Mode Button on DM82 or the START/PAUSE Button on the Remote Control.
3. Operating and Programming 6 Power OFF Pause DM82. Move the Side Power Switch to the OFF position. ** When DM82 is not cleaning, it is suggested to keep it powered ON and charging instead of powered OFF. 3.3 Cleaning Mode Selection DM82 has several cleaning modes to choose from to effectively clean different floors. Cleaning modes are selected using the Remote Control or the AUTO Mode Button on the robot. ** Before selecting a cleaning mode, make sure the AUTO Mode Button on DM82 flashes GREEN.
3. Operating and Programming 3 Edge Cleaning Mode 4 MAX Cleaning Mode This mode is good for cleaning the edges and corners of a room. In Edge Cleaning Mode, DM82 cleans along a border (e.g. wall). AM This mode is used to increase the suction power of any other cleaning mode already in process. Begin cleaning in the desired cleaning mode, then press the MAX button to increase suction power for deep cleaning.
3. Operating and Programming 3.4 Programming the Robot DM82 has a Time Scheduling function. DM82 can be programmed to automatically clean once per day, at a specific time even if nobody is at home. The current time of day and the cleaning time are scheduled using the Remote Control. ** All scheduled cleanings are performed in AUTO Cleaning Mode. ** Before programming the robot, make sure the AUTO Mode Button on DM82 flashes GREEN.
3. Operating and Programming 2 Schedule the Cleaning Time AM AM PM AM PM AM AM PM PM PM AM PM AM AM PM PM PM PM MAX Press the Time Scheduling Button on the Remote Control to schedule automatic cleaning. The “hour” in the first line on the screen flashes. PM AM AM MAX AM PM AM Press the up Direction Control Button and the MAX Button to adjust “hour” and “minute” number. Press the left and right Direction Control Buttons to switch between hour and minute.
3. Operating and Programming 3.5 Indicator Light and Alarm Sounds Indicator Light AUTO Mode Button on DM82 Status Flashes ORANGE The robot is charging. Glows a continuous GREEN The robot is fully charged. Flashes GREEN The robot is powered ON and is awake. Glows a continuous RED The robot has a problem. Flashes ORANGE The robot has low battery. Glows a continuous GREEN The robot is cleaning. Alarm Sounds If DM82 detects a problem, it emits alarm beeps and the AUTO Mode Button glows RED.
4. Maintenance Before performing cleaning and maintenance on DM82, power OFF the robot and unplug the Charging Dock. 4.1 Dust Bin and Filters Press the Dust Bin Release Button and remove the Dust Bin from the rear of DM82. Hold the Dust Bin level and open the Dust Bin Cover. Empty the Dust Bin. Pull the two handles on the Filter Net to remove it. Remove the Sponge Filter and the High Efficiency Filter. Pat the High Efficiency Filter clean. Do not rinse the High Efficiency Filter under water.
4. Maintenance 4.2 Main Brush and Side Brushes Cleaning the Main Brush Turn the robot over. Push the two tabs on the Main Brush Cover to remove it. Remove the Main Brush. Use the provided Cleaning Tool to remove any hair tangled around the Main Brush. Cleaning the Side Brushes Remove the Side Brushes with a screwdriver. Wipe the Side Brushes clean with a dry cloth. 4.3 Other Components Use the provided Cleaning Tool to remove any hair tangled around the Universal Wheel.
4. Maintenance Wipe the Charging Contacts and Charging Dock Pins with the brush side of the provided Cleaning Tool to maintain their effectiveness. Wipe the top cover of the robot with a soft dry or slightly damp cloth. Do not use cleaning solutions on the top cover as it could damage the surface. The top cover is tempered glass. While tempered glass is safer and stronger than standard glass, please handle with care to avoid scratching or breakage.
5. Troubleshooting Please use this chart to troubleshoot common problems using DM82. No. 1 2 3 Malfunction DM82 will not charge. DM82 gets into trouble while working and stops. DM82 returns to the Charging Dock before it finishes cleaning. Possible Cause Solutions DM82 is not powered ON. Move DM82’s Side Power Button to the ON position. DM82 has not made a connection with the Charging Dock. Be sure that DM82’s Charging Contacts have made a connection with the Charging Dock Pins.
5. Troubleshooting No. 4 5 20 EN Malfunction DM82 will not clean automatically at scheduled time. Remote Control failure (effective control range of Remote Control is 5m /16’). Possible Cause Solutions Time Scheduling function is cancelled. Set Time Scheduling function as described in section 3.4. DM82 is powered OFF. Power ON DM82. The robot’s battery is low. Keep DM82 powered ON and on the Charging Dock to make sure it has a full battery to work at any time.
DM82-EU01-IM2014R04