Contents 1. Important Safety Instructions.......................................................................2 ........................................6 2.1 Package Contents.....................................................................................6 2.3 Product Diagram........................................................................................8 3. Operating and Programming......................................................................10 3.1 Notes Before Cleaning.............
1. Important Safety Instructions When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. SAVE THESE INSTRUCTIONS 1.
1. Important Safety Instructions 9. Do not operate the Appliance in an area where there are lit candles or fragile objects. 10. Do not use in extremely hot or cold environments (below 11. Keep hair, loose clothing, fingers, and all parts of body away from any openings and moving parts. 12. Do not operate the Appliance in a room where an infant or child is sleeping. 13. Do not use Appliance on wet surfaces or surfaces with standing water. 14.
1. Important Safety Instructions 22. Turn OFF the power switch before cleaning or maintaining the Appliance. 23. The plug must be removed from the receptacle before cleaning or maintaining the Docking Station. 24. Remove the Appliance from the Docking Station, and turn OFF the power switch to the Appliance before removing the battery for disposal of the Appliance. 25. The battery must be removed and discarded according to local laws and regulations before disposal of the Appliance. 26.
1. Important Safety Instructions For EU Countries Correct Disposal of this Product This marking indicates that this product should not be disposed of with other household waste throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To recycle your used device, please use the return and collection systems or contact the retailer where the product was purchased.
2.
Model DG3G Working Voltage 14.8V DC Input 100-240V AC , 50/60Hz, 25W Laser max. power: 2.5mW Frequency: 1.8KHz Rotate Speed: 300±5 circle/min Docking Station Model Battery Frequency bands CH1630A Output 20V DC, 0.8A S01-LI-148-3200, Lithium 3200mAh, 14.8V 2412-2472MHz Output power of the WIFI module is less than 100mW.
2.3 Product Diagram Robot 18 19 20 5 1 21 6 2 8 3 9 10 4 1. Top Cover 2. Control Panel 3. Anti-Collision Sensors and Bumper 5. LDS Bumper 6. Anti-Drop Sensors 7. Charging Contacts 16 12 7 13 14 17 15 11 8. Main Brush Option 9. Driving Wheels 10. Reservoir Slots 11. Roller Wheel 12. Universal Wheel 13. Side Brushes 14. Battery Pack 15. Reservoir 16. Carpet Detection Sensor 17. Water Outlets 18. Power Switch 19. Upgrade Port 20. Multi-Function Cleaning Tool 21.
Dust Bin 1 2 34 5 2. Sponge Filter 3. Dust Bin Lock 4. Dust Bin Cover 5. Dust Bin Handle Advanced OZMO Mopping System 1 2 3 4 5 1. Water Inlet Cover 2. Water Inlet 3. Reservoir Release Button 4. Cleaning Cloth Plate Cleaning Cloth 6.
3. Operating and Programming 3.1 Notes Before Cleaning WARNING: Do not use DEEBOT on wet surfaces or surfaces with standing water. DEEBOT uses SMART NAVI technology (a proprietary laser scanning and operating DEEBOT, take a few moments to survey the area to be cleaned and remove any obstacles. Please supervise DEEBOT during its first cleaning and assist should there be a problem. Before using the product on an area rug with tasseled edges, please fold area rug edges under themselves.
3. Operating and Programming If there is a step or stairs in the cleaning area, please operate DEEBOT to ensure its Anti-Drop Sensors can detect the drop off. It may be necessary to place a physical barrier at the edge of the drop off to keep the unit from falling over the edge. If there is a step or stairs in the cleaning Please do not stand in narrow spaces, such as hallways, or DEEBOT may fail to identify the area to be cleaned. Please be aware that DEEBOT needs at furniture without complications.
3. Operating and Programming 3.2 Quick Start Remove the protection strip from the robot’s Bumper before use. 1 Docking Station Placement Plug the Docking Station in. * Do not change the location of the Docking Station once DEEBOT has scanned the environment. If it is necessary to relocate Docking Station, power OFF DEEBOT and then power back ON so DEEBOT can re-scan the environment. Alternatively, use the ECOVACS App to direct the robot to rescan the environment.
3. Operating and Programming 2 Install Side Brushes Attach Side Brushes to the bottom of DEEBOT by pressing a brush into each slot with the matching color until it clicks. 3 Power ON Open the Top Cover. Move the Power Switch to the ON position. “I”=power ON; “O”=power OFF. The Control Panel illuminates, and DEEBOT plays a musical tune. DEEBOT is powered ON when the Control Panel stays illuminated. * When DEEBOT is not c leaning, it is suggested to keep it powered ON and charging instead of powered OFF.
3. Operating and Programming 5 Start Press the AUTO Mode Button on DEEBOT. DEEBOT moves around to scan the environment and build the map, and starts to work in AUTO Cleaning Mode at the same time. * DEEBOT must be powered ON to clean. * To choose another Cleaning Mode, please refer to section 3.3 Cleaning Mode Selection for details. * Do not manually move the robot when it is cleaning or charging. * To add water into the Reservoir when DEEBOT is cleaning, pause the robot. Do not manually move it.
3. Operating and Programming * For models with app-connectivity, various functions can be performed using the ECOVACS App. 3.3 Cleaning Mode Selection Modes are selected using the ECOVACS App. 1 AUTO Cleaning Mode This is the most commonly used mode. In AUTO Cleaning Mode, DEEBOT cleans in a back and forth straight-line pattern. 2 Spot Cleaning Mode This mode is applicable for areas of highly concentrated dirt or dust. In Spot Cleaning Mode, cleaned with Spot Cleaning Mode using ECOVACS App.
3. Operating and Programming 3.6 Optional OZMO Mopping System Cloth and a Cleaning Cloth Plate attached to a proprietary Reservoir. The Washable/Reusable * When using the mopping system, DEEBOT automatically detects and avoids the rug. * * Empty any remaining water from the Reservoir and remove the Cleaning Cloth Plate before charging DEEBOT. Always keep the Reservoir installed when the robot is cleaning or charging.
3. Operating and Programming 3 Start Select the desired Cleaning Mode. DEEBOT sweeps, lifts, vacuums, mops and dries in the selected mode. 3.7 Choosing a Suction Option The robot has 2 interchangeable suction options for your convenience. Main Brush Option: The best choice for deep cleaning with a combination of the Main Brush and strong suction. The Main Brush Option comes pre-installed in DEEBOT.
3. Operating and Programming Install the Direct Suction Option Turn the robot over. Push both buttons on the Main Brush Option and remove the Main Brush Cover. Remove the Main Brush. Line up the Direct Suction Option tabs with the slots on the bottom of the robot. Press until the component clicks into place. Install the Main Brush Option Turn the robot over. Push both buttons on the Direct Suction Option and remove Direct Suction Option. Insert the Main Brush into the bottom of the robot.
4. Maintenance Before performing cleaning and maintenance on DEEBOT, power OFF the robot and unplug the Docking Station. 4.1 OZMO Mopping System After DEEBOT finishes mopping, remove the Reservoir from DEEBOT, and maintain the Reservoir, the Cleaning Cloth and the Cleaning Cloth Plate immediately. Press the Release Button and pull to remove the Reservoir. Remove the Cleaning Cloth Plate and the Cleaning Cloth. Empty any remaining water from the Reservoir.
4. Maintenance 4.2 Dust Bin and Filters Open the robot’s Top Cover and remove the Dust Bin. Open the Dust Bin Lock and empty the Dust Bin. water.
4. Maintenance Rinse the Dust Bin and Filter Net under running water. Dry the Dust Bin and Filter Net completely before reinstalling. 4.3 Main Brush, Direct Suction Option and Side Brushes * A Multi-Function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges. Main Brush Turn the robot over. Push both buttons on the Main Brush Option and remove the Main Brush cover. Remove the Main Brush.
4. Maintenance Side Brushes Remove the Side Brushes. Remove any hair or debris tangled around the Side Brushes with the provided Multi-Function Cleaning Tool, and wipe their slots with a clean cloth. 4.4 Other Components Use the Multi-Function Cleaning Tool to cut off and remove any hair tangled around the Universal Wheel. Wipe the Anti-Drop Sensors with the brush of the Multi-Function Cleaning Tool to maintain their effectiveness.
4. Maintenance * Before cleaning the robot’s Charging Contacts and Docking Station Pins, power OFF the robot and unplug the Charging Dock. Wipe the robot’s Charging Contacts and Docking Station Pins with a dry cloth to maintain their effectiveness.
4. Maintenance 4.5 Regular Maintenance To keep DEEBOT running at peak performance, perform the maintenance and replacement according to the following frequency. A multi-Function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.
5. Troubleshooting No. Malfunction Possible Causes DEEBOT is not powered ON. DEEBOT has not made a connection with the Docking Station. 1 2 3 4 DEEBOT will not charge. DEEBOT cannot return to the Docking Station. DEEBOT gets into trouble while working and stops. DEEBOT returns to the Docking Station before it ng. Docking Station is unplugged while DEEBOT is powered ON, which causes battery consumption.
5. Troubleshooting No. Malfunction 6 DEEBOT misses cleaning area. 7 The water is not coming out of the Reservoir when DEEBOT is mopping. Possible Causes The cleaning area needs tidying up. The Magnet on the Cleaning Cloth Plate comes off. 8 EN before DEEBOT starts cleaning. Please contact Customer Service. Add water into the Reservoir. The water outlets on the bottom of DEEBOT are clogged. Check the water outlets on the bottom and clean. DEEBOT is not within range of your home Wi-Fi signal.