EN Instruction Manual
Congratulations on the purchase of your ECOVACS Robotics WINBOT! We hope it brings you many years of satisfaction. We trust the purchase of your new robot will help keep your home clean and provide you more quality time to do other things. Live Smart. Enjoy Life. Should you encounter situations that have not been properly addressed in this Instruction Manual, please contact our Customer Service Center where a technician can address your specific problem or question.
Contents 1. Important Safety Instructions.......................................................................2 2. Package Contents and Technical Specifications.......................................4 2.1 Package Contents.....................................................................................4 2.2 Specifications............................................................................................4 2.3 Product Diagram.......................................................................
1. Important Safety Instructions When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. SAVE THESE INSTRUCTIONS 1. This Appliance is not intended to be used by children under 8 or anyone lacking knowledge on proper use. Supervision may be necessary. Do not allow children to play with the Appliance. 2. Do not use the Appliance in extremely hot or cold environments (below 0˚C/32˚F or above 40˚C/104˚F).
1. Important Safety Instructions 24. Please dispose of used batteries according to local laws and regulations. 25. Do not incinerate the Appliance even if it is severely damaged. The battery can explode in a fire. 26. The Appliance must be used in accordance with the directions in this Instruction Manual. The company cannot be held liable or responsible for any damages or injuries caused by improper use.
2. Package Contents and Technical Specifications 2.1 Package Contents EN FR DE ES Instruction Manual Mode d'emploi Benutzerhandbuch Manual de instrucciones Robot Power Adapter Instruction Manual Safety Pod and Tether (3) Cleaning Pads WINBOT Cleaning Solution (1) WINBOT Extension Cord (1.5m/4’11”) Finishing Cloth Remote Control with Batteries 2.
2. Package Contents and Technical Specifications 2.3 Product Diagram Robot 5 6 7 8 9 1 2 3 10 4 1. Status Indicator Light and START/PAUSE Button 2. Handle 3. Power Cord 4. Power Switch 5. Cleaning Pad 6. Driving Treads 7. Wheel Sensor 8. Bottom Status Indicator Light 9. Fan 10. Edge Detection Sensors Remote Control 1 RESET 2 3 N Z 1. RESET Button 2. Direction Control Buttons 3. START/PAUSE Button 4. “N” Cleaning Mode Button 5. “Z” Cleaning Mode Button 6.
3. Operating the Robot 3.1 Notes Before Cleaning 45 65 Do not use WINBOT 8 on a framed window with a frame smaller than 5mm (0.2”). WINBOT 8 can clean framed or frameless glass, larger than 45cm x 65cm (17.7’’ x 25.6’’). If WINBOT 8’s Status Indicator Light flashes If the window is covered with dirt, clean a GREEN after powering ON, the Back-Up small area on the glass before use and place Battery requires charging. Keep WINBOT WINBOT 8 there.
3. Operating the Robot 3.2 Attach the Cleaning Pad 3.3 Assemble the Power Adapter Turn WINBOT 8 over and attach the Cleaning Pad to the Velcro smoothly. Make sure the Cleaning Pad is placed exactly within its Velcro area and does not cover the Fan or Edge Detection Sensors. 3.4 Install the Safety Tether If WINBOT is used to clean an outside window, the Safety Pod and Tether MUST be used. * If WINBOT 8 is being used to clean an inside window please skip to step 3.6.
3. Operating the Robot 1 Loop one end of the Safety Tether to End A on the Robot Power Cord and tighten. 2 Connect End A and End B and tighten. 3 Loop the other end of the Safety Tether around the Safety Pod’s channel and pull it tight. * If the length of the power cord restricts WINBOT 8’s movement, a WINBOT Extension Cord can be used. Disconnect End A and End B, and connect them with both ends of the Extension Cord respectively and tighten.
3. Operating the Robot 3.5 Place the Safety Pod The Safety Pod MUST be placed on the inside of the window. Press the Safety Pod FIRMLY on the inside of the window being cleaned. Make sure the Safety Pod is attached and securely in place. 3.6 Spray Cleaning Solution * WINBOT should only be used with WINBOT Cleaning Solution. Using other cleaners significantly reduces WINBOT’s performance and can damage the robot.
3. Operating the Robot 3.7 Start 1 Plug in WINBOT 8 2 Power ON Move the Power Switch to the “ ” position. WINBOT 8 is powered ON when the Status Indicator Light flashes BLUE. 3 Place on the Glass Place WINBOT 8 on the window at least 10cm (4”) from window corners or other obstacles. WINBOT 8 has successfully attached to the window when the Status Indicator Light glows a continuous BLUE. * Please ensure there is a 15cm (5.9”) clearance between the glass and obstacles in the room like curtains or furniture.
3. Operating the Robot 4 Start Press the START/PAUSE button on WINBOT 8 or on the Remote Control to begin cleaning. To change Cleaning Modes, Pause WINBOT by pressing the START/PAUSE button on WINBOT 8 or on the Remote Control, then press the “Z” or “N” Cleaning Mode Button on the Remote Control. “N” Cleaning Mode is the default Cleaning Mode and is also ideal for tall windows. “Z” Cleaning Mode is best for wide windows. * Do not unplug WINBOT 8 while it is cleaning. 3.
3. Operating the Robot 3.9 Stop When WINBOT 8 completes its cleaning cycle, it returns to the place it started and beeps. 1 Remove WINBOT 8 Grasp WINBOT 8’s Handle. Press and hold for approximately 5 seconds and the fan will stop. Remove WINBOT 8 from the window. Polish away any marks left on the glass from WINBOT’s removal with the provided Finishing Cloth. 2 Power OFF Move the Power Switch to the “o” position. OFF 3 Remove the Safety Pod, if used.
4. Maintenance Before performing cleaning and maintenance on WINBOT 8, move the Power Switch to the “o” position and unplug it from the receptacle. 4.1 Cleaning Pad Turn the robot over and remove the Cleaning Pad. Rinse the Cleaning Pad and allow it to dry completely before re-attaching it to the robot. * Do NOT use a wet Cleaning Pad on WINBOT 8 or it may slip on the window. 4.
4. Maintenance 4.3 Driving Treads Move the Power Switch to the “I” position. Press and hold the robot’s START/PAUSE Button for 5 seconds to stop the Fan. Turn WINBOT 8 over. Inspect the Driving Treads by using the and buttons on the Remote Control. Stop the Driving Treads if dirt is seen on the Treads. Move the Power Switch to the “O” position. Clean any dirt on the Driving Treads with the provided Finishing Cloth. ON 5.
6. Troubleshooting NO. 1 2 Malfunction Remote Control does not work Status Indicator Light flashes BLUE after WINBOT 8 is placed on the glass Possible Causes Solutions WINBOT 8 is cleaning. When WINBOT 8 is cleaning, only the START/PAUSE Button works on the Remote Control. Pause WINBOT 8 by pressing the START/PAUSE button on the robot or Remote Control. Other buttons on the Remote Control will function when WINBOT 8 is paused. The Remote Control is not paired with WINBOT 8.
6. Troubleshooting NO. 3 4 16 EN Malfunction Possible Causes Solutions Interruption of electricity while WINBOT 8 was cleaning due to power failure, plug displacement, or loose connection to the Power Adapter. A. Connect WINBOT 8 to the Power Adapter and plug into the wall receptacle. Press Start/Pause Button on the robot or on the Remote Control. WINBOT 8 will resume cleaning. B.
Toutes nos félicitations pour l'achat de votre WINBOT d’ECOVACS Robotics! Nous espérons qu'il vous apportera de nombreuses années de satisfaction. Nous sommes persuadés que votre nouveau robot vous aidera à garder votre maison propre et vous permettra d'économiser du temps pour vivre intelligemment et apprécier la vie. Live Smart. Enjoy Life.
WINBOT 8-038-IM2014R01