EN Instruction Manual Note: This Instruction Manual applies to units purchased in North America only.
Congratulations on the purchase of your ECOVACS ROBOTICS WINBOT! We hope it brings you many years of satisfaction. We trust the purchase of your new robot will help keep your home clean and provide you with more quality time to do other things. Before you go any further, please register your product on the ECOVACS ROBOTICS website at www.ecovacsrobotics.com/registration/. We also suggest you record your model number, serial number, date of purchase and attach your receipt to this page for safekeeping.
Contents 1. Important Safety Instructions.......................................................................2 2. Package Contents and Technical Specifications.......................................4 2.1 Package Contents.....................................................................................4 2.2 Specifications............................................................................................4 2.3 Product Diagram.......................................................................
1. Important Safety Instructions When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. SAVE THESE INSTRUCTIONS 1. This Appliance is not intended to be used by children under 8 or anyone lacking knowledge on proper use. Supervision may be necessary. Do not allow children to play with the Appliance. 2.
1. Important Safety Instructions 24. Please dispose of used batteries according to local laws and regulations. 25. Do not incinerate the Appliance even if it is severely damaged. The battery can explode in a fire. 26. The Appliance must be used in accordance with the directions in this Instruction Manual. ECOVACS ROBOTICS cannot be held liable or responsible for any damages or injuries caused by improper use.
2. Package Contents and Technical Specifications 2.1 Package Contents WINBOT Power Adapter Instruction Manual Safety Pod and Tether (3) Cleaning Pads WINBOT Cleaning Solution (1) WINBOT Extension Cord (1.5m/4’11”) Finishing Cloth Remote Control with Batteries 2.2 Specifications WINBOT model Working Voltage W950 24V DC Rated Power 75W Remote Control Rated output voltage 3V DC Power Adapter: EA10952E Input: 100-240V AC 50/60Hz 2.5A Output: 24V DC 3.
2. Package Contents and Technical Specifications 2.3 Product Diagram WINBOT 6 7 8 9 10 11 1 2 3 12 13 4 14 5 15 16 17 1. Speaker 2. Status Indicator Light/START/PAUSE Button 3. Handle 4. Upgrade Port (for after-sale service) 5. Power Cord 6. Edge Detection Sensors 7. Cleaning Pad 8. Squeegee 9. Bottom Power Switch 10. Bottom Status Indicator Light 11. Suction Sensor 12. Fan 13. Driving Treads 14. Balance Wheel 15. Cleaning Pad Plate 16. Cleaning Pad Velcro 17.
3. Operating WINBOT 3.1 Notes Before Cleaning 6 Do not use WINBOT on a framed window with a frame smaller than 5mm (0.2”). WINBOT can clean framed or frameless glass, larger than 45cm x 45cm (17.7’’ x 17.7’’). If WINBOT ’s Status Indicator Light flashes GREEN af ter power ing ON, the Back-Up Batter y requires charging. Keep WINBOT plugged in to charge the Back-Up Battery until the Status Indicator Light flashes BLUE, and WINBOT can now start cleaning.
3. Operating WINBOT WINBOT is intended to be used for maintenance cleaning on common windows. The product is not designed to replace heavy-duty or first time cleaning. Please ensure there is a 15cm (5.9”) clearance between the glass and obstacles in the room like curtains or furniture. WINBOT can clean horizontally mounted glass but only when using the Direction Control Buttons on the Remote Control.
3. Operating WINBOT 3.4 Install the Safety Tether B C End A: WINBOT Power Cord End C: Safety Pod D End B: Power Adapter Power Cord End D: Safety Tether 1 Loop one end of the Safety Tether to End A on the WINBOT Power Cord and tighten. 2 Connect End A and End B and tighten.
3. Operating WINBOT 3 Loop the other end of the Safety Te t h e r a r o u n d t h e S a f e t y Po d ’s channel and pull it tight. * If the length of the power cord restricts WINBOT’s movement, a WINBOT Extension Cord can be used. Disconnect End A and End B, and connect them with both ends of the Extension Cord respectively and tighten. * Only one Extension Cord can be used with WINBOT. 3.5 Place the Safety Pod Wipe the surface of the Safety Pod’s suction cup clean with the provided Finishing Cloth.
3. Operating WINBOT 3.6 Spray Cleaning Solution * It is recommended to use WINBOT with WINBOT Cleaning Solution from ECOVACS. Using tap water or other cleaners could have an adverse effect on cleaning performance. Using other cleaning solutions could potentially nullify the warranty. Spray the each side of the Cleaning Pad with the provided WINBOT Cleaning Solution 8 times. 3.7 Start 1 Plug in WINBOT * Do not unplug WINBOT while it is cleaning.
3. Operating WINBOT 2 Power ON Move the Power Switch to the “ ” position. WINBOT is powered ON when the Status Indicator Light flashes BLUE. * Keep objects away from WINBOT’s Fan to avoid blockage. 3 Place on the Glass Place WINBOT on the window at least 10cm (4”) from window corners or other obstacles. WINBOT has successfully attached to the window when the Status Indicator Light glows a continuous BLUE. * Please ensure there is a 15cm (5.
3. Operating WINBOT 3.8 Pause Pause WINBOT during cleaning by pressing the START/PAUSE button on the robot or on the Remote Control. Direct WINBOT to move forward, backward, left and right using the Direction Control Buttons on the Remote Control when Paused. WINBOT cleans when the Direction Control Buttons are used. 3.9 Stop When WINBOT completes its cleaning cycle, it returns to the place it started and beeps. 1 Remove WINBOT Grasp the robot ’s Handle.
3. Operating WINBOT 3 Remove the Safety Pod. 4 Unplug WINBOT Polish away any marks left on the glass from the Safety Pod’s removal with the provided Finishing Cloth. Notes: If WINBOT has a problem and the indicator Light flashes RED, it can be reset by pressing the RESET Button on the Remote Control. See “Troubleshooting” for details.
4. Maintenance Before performing cleaning and maintenance on WINBOT, Power OFF and unplug WINBOT from the receptacle. 4.1 Cleaning Pad Turn WINBOT over and remove the Cleaning Pad. Soak the Cleaning Pad in cool, clean water for 2 minutes. Hand wash with mild detergent and lay flat to dry. Allow it to dry completely before re-attaching it to WINBOT. * Do NOT use a wet Cleaning Pad on WINBOT or it may slip on the window. * Washing the Cleaning Pad regularly can extend its service life.
4. Maintenance Edge Detection Sensors Squeegee Turn WINBOT over and wipe the four Edge Detection Sensors clean with the provided Finishing Cloth to maintain their effectiveness. Turn WINBOT over and wipe the Squeegee with the provided Finishing Cloth to maintain its effectiveness. 4.3 Driving Treads Plug WINBOT in. Turn WINBOT over and move the Power Switch to “ ” position. Press and hold the START/PAUSE Button for 5 seconds to stop the Fan.
5. Status Indicator Light and Sounds Indicator 16 Description Status Indicator Light flashes GREEN Back-Up Battery is low and is charging. WINBOT will not clean until the Back-Up Battery is properly charged. Status Indicator Light stops glowing The Status Indicator Light stops glowing when the Back-Up Battery is fully charged. This is normal. Status Indicator Light flashes BLUE WINBOT is powered ON and ready to be placed on the glass.
6. Troubleshooting NO. 1 2 Malfunction Remote Control does not work. Possible Causes Solutions WINBOT is cleaning. When WINBOT is cleaning, only the START/PAUSE Button works on the Remote Control. Pause WINBOT by pressing the START/PAUSE button on the robot or Remote Control. Other buttons on the Remote Control will function when WINBOT is paused. The Remote Control is not paired with WINBOT. WINBOT arrives from the factory paired with its Remote Control.
6. Troubleshooting NO. 3 18 FR-CA EN Malfunction Status Indicator Light of the product flashes RED. Possible Causes Solutions Interruption of electricity while WINBOT was cleaning due to power failure, plug displacement, or loose connection to the Power Adapter. A. Connect WINBOT to the Power Adapter and plug into the wall receptacle. Press Start/Pause Button on WINBOT or on the Remote Control. WINBOT will resume cleaning. B.
6. Troubleshooting NO. 4 5 Malfunction WINBOT moves in an irregular pattern during cleaning. WINBOT is stuck with Indicator Light flashing, and cannot move, be controlled by the Remote Control, or be reset by pressing RESET. Possible Causes Solutions There is too much dirt and debris on the window. A. Spray additional Cleaning Solution on the Cleaning Pad. B. Clean the Driving Treads as described in section 4. C. Replace the Cleaning Pad and restart the cleaning cycle. D.
Designed and Manufactured by / Conception et fabrication par/Diseñado y Fabricado por ECOVACS ROBOTICS, Co., Ltd. MADE IN CHINA/FAIT EN CHINE/HECHO EN CHINA Distributed by/Distribué par/Distribuido por ECOVACS ROBOTICS, Inc. Canton, OH, USA/Canton, OH, EE.UU.