EN Instruction Manual
Live Smart. Enjoy Life. Congratulations on the purchase of your Ecovacs Robotics WINBOT! We hope it brings you many years of satisfaction. We trust the purchase of your new robot will help keep your home clean and provide you with more quality time to do other things. Before you go any further, please register your product on the Ecovacs website at www.ecovacsrobotics.com/registration/.
Contents 1. Important Safety Instructions...................................................................... 2 ...................................... 4 2.1 Package Contents .................................................................................... 4 2.2 ........................................................................................... 4 2.3 Product Diagram ...................................................................................... 5 3. Operating the Robot .................
1. Important Safety Instructions When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. SAVE THESE INSTRUCTIONS 1. This Appliance is not intended to be used by children under 8 or anyone lacking knowledge on proper use. Supervision may be necessary. Do not allow children to play with the Appliance. 2. Do not use the Appliance in extremely hot or cold environments (below 0˚C/32˚F or above 40˚C/104˚F).
1. Important Safety Instructions 21. The Back-Up Battery must be replaced by the manufacturer or its service agent in order to avoid a hazard. 22. The Back-Up Battery must be removed and discarded according to local laws and regulations before disposal of the Appliance. 23. The Appliance must be disconnected from the receptacle before removing the battery for disposal of the Appliance. 24. Please dispose of used batteries according to local laws and regulations. 25.
2.1 Package Contents Robot Power Adapter (3) Sets of Cleaning Pads WINBOT Cleaning Solution Instruction Manual Safety Pod and Tether Remote Control with Batteries (1) WINBOT Extension Cord (1.5m/4’11”) Model Working Voltage (V) Finishing Cloth W730/W710 15=== Rated Power (W) 35 Remote Control 3 === Input Voltage(V) Power Adapter: WT1503000 Input *Technical and design 4 EN 100-240V~ 50/60Hz 1.6A Output 15V=== 3.0A may be changed in the course of continuous product improvement.
2.3 Product Diagram Robot 1 8 9 2 10 13 11 12 3 4 5 14 15 6 1. Bumper 2. Status Indicator Light 3. START/PAUSE Button 4. Air Release Trigger 5. Power Cord 7 6. Handle 7. Power Switch 8. Side Rollers 9. Front Cleaning Pad 10. Squeegee 11. Driving Treads 12. Cupule 13. Bottom Status Indicator Light 14. Rear Cleaning Pad 15. Edge Detection Sensors (W730 ONLY) Remote Control 1 2 3 1. RESET Button 2. Direction Control Buttons 3. START/PAUSE Button 4.
3. Operating the Robot 3.1 Notes Before Cleaning 45 60 6 Do not use WINBOT 7 on a framed window with a frame smaller than 5mm (0.2"). WINBOT 7 can be used on framed or frameless* windows larger than 45cm x 60cm (17.7’’ x 23.6’’). (*W730 only) WINBOT 7’s Back-Up Battery must be fully charged before use. Plug WINBOT 7 in, move the Power Switch to the CHARGE position, and charge until the Status Indicator Light glows a continuous GREEN.
3. Operating the Robot 3.2 Attach the Cleaning Pads Turn WINBOT 7 over and attach the Cleaning Pads to their Velcro areas smoothly. Make sure the Rear Cleaning Pad is placed exactly within its Velcro area and does not contact or cover the Cupule (suction ring). 3.3 Assemble the Power Adapter 3.4 Install the Safety Tether If WINBOT 7 is used to clean an outside window, the Safety Pod and Tether MUST be used. * If WINBOT 7 is being used to clean an inside window, please skip to step 3.6.
3. Operating the Robot 1 Loop one end of the Safety Tether to End A on the Robot Power Cord and tighten. 2 Connect End A and End B and tighten. 3 Loop the other end of the Safety Tether around the Safety Pod’s channel and pull it tight. * If the length of power cord restricts WINBOT 7’s movement, a WINBOT Extension Cord can be used. Disconnect End A and End B, and connect them with both ends of the Extension Cord respectively and tighten.
3. Operating the Robot 3.5 Place the Safety Pod The Safety Pod MUST be placed on the inside of the window. Press the Safety Pod FIRMLY on the inside of the window being cleaned. Make sure the Safety Pod is attached securely in place. 3.6 Spray Cleaning Solution * WINBOT 7 should only be used with WINBOT Cleaning Solution. Using other cleaners significantly reduces WINBOT’s performance and can damage the robot. Spray the Front Cleaning Pad with the provided WINBOT Cleaning Solution 3 times.
3. Operating the Robot 3.7 Start 1 Plug in WINBOT 7 2 Power ON Move the Power Switch to the “ON” position. WINBOT 7 is powered ON when it generates suction. * WINBOT 7’s Back-Up Battery must be fully charged before use. Plug WINBOT 7 in, move the Power Switch to the CHARGE position until the Status Indicator Light glows a continuous GREEN. 3 Place on the Glass Place WINBOT 7 on the window at least 10cm (4’’) from the corners and other obstacles and press it on the window.
3. Operating the Robot 3.8 Pause Pause WINBOT 7 during cleaning by pressing the START/PAUSE button on the robot or on the Remote control. WINBOT 7 can be directed to move forward, backward, left and right using the Direction Control Buttons on the Remote Control when Paused. WINBOT 7 will clean when Direction Control Buttons are used. 3.9 Stop When WINBOT 7 completes its cleaning cycle, it returns to the place it started and beeps. 1 Remove WINBOT 7 Grasp WINBOT 7’s handle.
4. Maintenance Before performing cleaning and maintenance on WINBOT 7, move the Power Switch to the “OFF” position and unplug it from the receptacle. 4.1 Cleaning Pads Turn the robot over and remove the Cleaning Pads. Rinse the Cleaning Pads and allow them to dry completely before re-attaching it to the robot. * Do NOT use wet Cleaning Pads on WINBOT 7, or it may slip on the window. 4.
4. Maintenance Edge Detection Sensors Squeegee Turn the robot over and remove the Cleaning Pads. Wipe the Edge Detection Sensors clean with the provided Finishing Cloth to maintain their effectiveness. (W730 ONLY) Turn the robot over and wipe the Squeegee clean with the provided Finishing Cloth to maintain its effectiveness. 4.3 Driving Treads Move the Power Switch on WINBOT 7 to the CHARGE position. Inspect the entire Driving Treads by using and buttons on the Remote Control.
5. Status Indicator Light and Sounds Indicator 14 Description Status Indicator Light GREEN Back-Up Battery is low and is charging. Status Indicator Light glows a continuous GREEN Back-Up Battery is fully charged and WINBOT 7 is ready to use. Status Indicator Light BLUE WINBOT 7 has successfully attached itself to the glass and is ready to clean. Status Indicator Light glows a continuous BLUE WINBOT 7 is cleaning the window. Status Light Indicator glows RED WINBOT 7 has a problem.
6. Troubleshooting No. 1 2 Malfunction Remote Control does not work. Status Indicator Light BLUE does not after WINBOT 7 is placed on the glass. Possible Causes Solutions WINBOT 7 is cleaning. When WINBOT 7 is cleaning, only the START/ PAUSE Button works on the Remote Control. Pause WINBOT 7 by pressing the START/PAUSE Button on the robot or the Remote Control. Other buttons on the Remote Control will function when WINBOT 7 is paused.
6. Troubleshooting 3 16 EN Status Light Indicator RED after it is powered ON, or during cleaning. WINBOT 7 has encountered a problem. A. Power OFF WINBOT 7 and unplug it. Then plug in again and power ON. B. Reset WINBOT 7 by pressing the RESET Button on the Remote Control. C. Check for stubborn stains on the window. Clean the stains before using WINBOT 7. D. Check the Cupule for dirt or damage. Clean the Cupule as described in section 4. If Cupule is scratched or damaged, replace it with a new one. E.
WINBOT 7-000IM2014R00