INSTRUCTION MANUAL MODEL: AVPUSB01S USB RECORDABLE TURNTABLE
Contents Page Contents……………………………………………………..……………………………….…….……….. 2 Important Safety Instructions…………………………………………………………….……….………... 3 Precautions……………………………………………………………………………….……….…………4 Before Use………………………………………………………………………….…….…….……………5 Location of Parts……………………………………………………………………….……….……………5 Turntable Set Up…….………………….……………………………………………… …….…..….……. 5 Listening to a Record……….…………………………………………………..…………….………….…. 6 How to Replace the Turntable Stylus……………………………………………………….……………… 6 Software Introduction…….
IMPORTANT SAFETY INSTRUCTIONS When using electrical products, basic precautions should always be followed. Please refer below: 1. Read Instructions - All safety and operating instructions should be read before the product is operated. 2. Retain Instructions - Safety and operating instructions should be retained for future reference. 3. Follow Warnings - All warnings on the product and in the manual should be adhered to. 4. Follow Instructions - All operating and user instructions should be followed. 5.
c. If the product has been exposed to rain or water. d. If the product does not operate and you have followed the manual for troubleshooting. e. If the product has been dropped or damaged in any way, and the product exhibits a distinct change in performance may indicate a need for service and/or repair. 18. Replacement Parts - If a part needs to be replaced, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part.
BEFORE USE • Choose a good location and avoid placing the unit in direct sunlight or near any heat source. • Avoid locations subject to vibrations, excessive dust, cold or moisture. • Do not open the cabinet as this may result in electrical shock. If a foreign object is inserted accidentally contact your dealer. • When removing the power plug from the wall outlet, always pull directly on the plug and not the cord. • Do not attempt to clean the unit with chemical solvents as this might damage the finishing.
LISTENING TO A RECORD 1. Connect the AC power cord to an electrical outlet. The standard voltage is 120V-50HZ. 2. Plug the other end of the RCA Cable into the auxiliary input (Aux) on your TV, receiver or other music system and make sure that the red RCA Cable is inserted into the red jack and the white RCA Cable is inserted into the white jack. 3. Press the POWER button located on the front of the unit. 4. Place a record on the turntable.
SOFTWARE INTRODUCTION Audacity application software is included with your USB Recordable Turntable and is designed to record and save music from the photograph to a computer. The software then allows for the same recorded files to be converted and edited to .WAV and/or .MP3 file formats. The recorded music can then be played using Windows Media Player and other applications that support .WAV and .MP3 formats.
3. Continue to click on the "Next" button until the software installation begins.
4. Click on the "Install" button to start the Audacity software installation. 5. Click on "Finish" to complete installation.
6. You can now open the Audacity software and start recording your files. RECORDING OPERATION STEPS 1. Connect the USB cable to your turntable and your computer 2. Press the POWER button and start to play your record 3. Double click the Audacity program and you will see this interface screen on your computer. 4. Adjust the output and input volume.
5. Select the RECORD button 6. Select the to start recording. button to go to start. button to go to end. 7. Select the 8. Select the PAUSE 9. Select the STOP button to pause the recording. button to stop the recording. 10. You can see the recorded file on your computer and convert the recorded file to other formats including .WAV and MP3.. 11. Play the saved file. Put the saved file into the Audacity program and press the PLAY 11 button to play the file.
CONVERTING THE RECORDED FILES TO .WAV AND .MP3 FILE FORMATS Please make sure that you have properly connected the USB Turntable to your computer and follow the instructions below to convert your files to “.wav and .mp3” file formats. 1. Make sure that the Audacity installation disc is still inserted in your computer. Go to your Desktop and double click on the "My Computer" icon. 2. Locate the CD ROM Drive and double click on the icon. 3. Copy the lame_enc.dll file and paste it to your Desktop. 4.
6. Locate "File Format" tab and click on the "Find Library" button.
7. Click "Yes" button, then go to your Desktop and highlight the lame_enc.dll. Next, click on the "Open" button. 8. Click on the "OK" button and return to the default window of the Audacity Software.
9. Click on the "File" tab and the option will be given to export the recorded file as “.wav”, “.mp3” or “.ogg” file formats. 10. Once you have selected the desired file format to export your recorded music, enter the file name and location where you want to save the file on your computer. Once finished, click on the "Save" button.
11. Enter the title, artist and any other information about the MP3 file that you have created and click on the "OK" button. 12. Next, go to the location of the file you have converted. supports .WAV or MP3 formats. You can play the converted file on any application that NOTE: Converted files can be transferred (burned) to a CD. with your CD burner or computer for additional details.
SPECIFICATIONS TURNTABLE PLAYER SECTION Motor…………………………………………………………..…..……….. .DC servo motor Drive System………………………..……. …………………………………Belt Drive Speeds………………………………..………………………………………33-1/3 rpm, 45 rpm and 78 rpm S/N Ratio…………………….…………………………………………..…. .More than 50 dB Cartridge Type…………………………………………………………..…. .Ceramic Stereo Cartridge Stylus…………………………………………………………..… 402-M208-165 Output Level……………….…………………………………………………160-380 mV (5 cm/sec at 1 KHz) GENERAL Power Requirements……..………………………………………….
MODEL: AVPUSB01S USB Recordable Turntable Grace Digital Inc.
