Extreme Sub ES08 Models: GDI-EXESW800...
Extreme Sub Layout Backlit Subwoofer (Passive) RIGHT SIDE Control Panel FRONT Auto-Turn-On Switch Backlit Subwoofer Heat Sink 2 LEFT SIDE BACK
In/Out Connections Remote Gain Level Control Aux-In / Sub-In Jack (Green) Jack (Black) Remote Turn-On Jack (Dark Blue) 12VDC Power-In Connector (EC5, Male) Do NOT use these connections if they are wet. Aux-In / Sub-In Jack: If you do not want to connect the Extreme Sub wirelessly via EcoCast or want to connect it to a non-ECOXGEAR amplifier or speaker, you can connect the subwoofer using this input and the supplied 3.5mm Audio Cable.
Connecting to 12VDC Power Supply The Extreme Sub does not have an internal battery. It must be connected to an external 12VDC power supply to function. Before you connect the Extreme Sub to a battery or a voltage regulator on a golf cart, a boat, a quad bike, a UTV, or another vehicle, you need to confirm the following: 1. Your vehicle battery or battery pack’s terminal voltage is 12VDC. 2. Your vehicle battery or battery pack can supply a 30A current rating to the Extreme Sub.
Use Caution: Do NOT attempt to loosen nuts if battery is wet. Contact may cause electric shock and injury if wet. 2. Connect the BLACK wire to the BLACK, negative terminal. 3. Connect the RED wire to the RED, positive terminal. Unit will not work correctly and may be damaged if wires are not correctly attached. Black Cable Red Cable 4. Tighten the nuts on the battery terminals until the connectors are held firmly in place. 5. Connect the (EC5) female connector on the 6.
Installation: Electric Vehicle 1. Switch your vehicle to TOW mode. 2. Wire the BLACK wire on the Extreme Sub power cable to the GROUND on output of the DC-DC Converter. 3. Wire the RED wire on the Extreme Sub to the POSITIVE (+) post on the output of the DC-DC converter. Unit will not work correctly and may be damaged if wires are not correctly attached. Black Cable Red Cable 5. Connect the (EC5) female connector on the 6.6ft Power Cable to the (EC5) male 12VDC Power-In Connector.
Controls 1 5 2 3 4 6 CONTROL PANEL 7 AUTO-TURNON SWITCH 1. LED Indicators: Each of the 2 LEDs correspond to different functions: AUX, Phase, and EcoCast Receiving. 2. Phase Button: Press this button to toggle the Extreme Sub sound output from in phase to out of phase. If the AUX LED flashes Green 3 times, the sound output is in phase. If the AUX LED flashes Red 3 times, the sound output is out of phase. 3. EcoCast Button: When turned on, the Extreme Sub enters EcoCast Receiving Mode.
Operations Auto-Turn-On Switch Turn the Auto-Turn-On Switch to select one of three modes: Remote, Audio, and DC. Remote: When the switch is turned to this position, the (Dark Blue) Remote Turn-On Cable must be connected to the vehicle ignition switch or the vehicle’s 12VDC power supply. When the vehicle’s ignition is on or the Remote Turn-On Cable has a 12VDC signal, the Extreme Sub will turn on.
Phase Button Press PHASE briefly to toggle the Extreme Sub sound output from in phase to out of phase. If the AUX LED flashes Green 3 times, the sound output is in phase. If the AUX LED flashes Red 3 times, the sound output is out of phase. Note: Pairing multiple subwoofers, depending on their location to one another, can result in the subwoofers sounding out of phase with each other and a reduction in their overall, perceived volume output.
Notes: · When the crossover frequency is set to 275Hz, you receive the full range of the Extreme Sub’s capability. This allows it to play low woofer frequencies, not just subwoofer frequencies, to produce a more full sound profile when paired with ECOXGEAR SoundExtreme soundbars. · When the crossover frequency is reduced down to 50Hz, the Extreme sub will perform solely as a low-frequency subwoofer.
EcoCast: SoundExtreme to Extreme Sub B A 1. Follow the Pairing a Bluetooth Device instructions in your SoundExtreme user guide to connect one SoundExtreme (Speaker A) to your Bluetooth device. After your device is connected to Speaker A, you can select a song to play. 2. Press on Speaker A to initiate EcoCast Transmitting Mode. The Mode LED Indicator (the third LED Indicator from the left) will flash Red, and the speaker will announce, “EcoCast transmitting.” 3. Power on your Extreme Sub (Sub B).
2. On Speaker A (the speaker with the Mode LED Indicator shining solid Red), PRESS AND HOLD for 6 seconds. The Mode LED Indicator will flash Red. 3. Once the connection between the speakers is successful, Speaker C (and Sub D) will announce, “Connection Successful,” and start playing music from your Bluetooth device.
Remote Gain Level Controller 1. Mount the Remote Gain Level Controller in an accessible location. Keep the cable away from the vehicle’s electrical wiring to avoid possible interferences from the vehicle’s electrical system. 2. Connect the Remote Gain Level Controller to the (Green) Remote Gain Level Control Jack on the Extreme Sub. The LED on the Remote Gain Level Controller will shine solid Red if the Extreme Sub is turned on. 3. Turn the knob to adjust the gain level.
Mounting Your Subwoofer Use Caution: · The Extreme Sub weighs 17 lbs. Please use caution when lifting or handling. · The Extreme Sub vibrates when playing heavy bass music at maximum gain. It is important to fasten the subwoofer securely to a flat surface on the vehicle. Whether mounting the subwoofer horizontally or vertically, the supplied Washers and Lock Washers MUST be used. · There is a Heat Sink on the back of the Extreme Sub.
Optional: Place the Mount Standoffs under both ends of the Mounting Plate. Use these optional Standoffs when there is not enough clearance between the Mounting Plate and the vehicle’s mounting surface. 4. Attach the Mounting Plate to your vehicle with the provided ¼-20 Hex Bolts, Washers, Lock Washers, and Nuts. Tighten securely. Vertical Mounts 1.
Troubleshooting No audio and LED indicator are off Check if there is voltage at Power-In connector or if there is an ignition signal when the Auto-Turn-On Switch is set to Remote, or if there is an audio signal input when the Auto-Turn-On Switch is set to Audio. Poor audio quality Check if the Gain Level is set properly. Check wires for shorts or grounds. Check the source signal. Check if the 3.5mm Audio Cable or the Remote Gain Level Controller cable is close to the vehicle’s electrical wiring.
9.7 in / 246 mm Unit + Horizontal Mount Dimensions 16.1 in / 410 mm 11.7 in / 296 mm Unit + Horizontal Mount + Mount Standoffs Dimensions 16.1 in / 410 mm 14.6 in / 371 mm Unit + Vertical Mount Dimensions 12 in / 306 mm Unit Weight 16.87 lbs (7.65 kg) Horizontal Mount Weight 1.5 lbs (0.68 kg) Vertical Mounts Weight 1.28 lbs (0.64 lbs x2) 0.58 kg (0.29 kg x2) Bluetooth Compliance Bluetooth V 5.0 Bluetooth Frequency Band 2.402~2.
FCC STATEMENT: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.) This device may not cause harmful interference, and 2.) This device must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
3.) Properly clean the ECOXGEAR and ensure the gaskets have no sand, dirt, or water on them prior to storage. 4.) Store your unit with all caps properly sealed to avoid long term internal moisture damage inside your unit. 5.) Return the ECOXGEAR to Grace Digital if you suspect water ingress into the unit or if the unit has experienced a severe impact that may have affected the integrity of the unit to take on water. You should never 1.) Never power your ECOXGEAR if you suspect water has entered the device.
What’s in the Box Extreme Sub ES08 Models: GDI-EXESW800...20 POWERSPORTS + GOLF CARS + MARINE SUBWOOFER User Guide Extreme Sub Subwoofer 6.6ft Power Cable - EC5, Female 6.6ft Remote Turn-On Cable - Dark Blue Extreme Sub User Guide (8pcs) Lock (8pcs) Washers Washers – small – small (8pcs) 10-24 x 29/32” Stainless Steel Button Head Screws (8pcs) ¼ Lock Washers 6.6ft 3.
Pairing the SoundExtreme with Your Remote Control Before you use your Remote Control for the first time, please follow the steps below. STEP 1 Pull and remove the plastic tab at the bottom of the Remote Control. Your Remote Control should be paired to your unit. IF NOT paired, complete Step 2. STEP 2 Pair your Remote Control with the SoundExtreme. a. Connect the SoundExtreme to a 12V power supply. (Refer to Connecting to 12VDC Power Supply in the User Guide for details.) b.
Product Warranty Registration To register your purchased product, please visit: www.ecoxgear.com/register or please enter all fields below and return this postal card by mail NAME: ADDRESS: CITY, STATE, ZIP: EMAIL: PRODUCT MODEL: DATE OF PURCHASE: PLACE OF PURCHASE: Please note: Product registration does not constitute proof of purchase for the warranty process. Please keep all receipt and purchase records as your evidence of the date and place of purchase.
Insert Postage Here A E(OXGEAR 10531 4S COMMONS DRIVE SUI TE 430 SAN DI EGO, CA 92127-3517 11.1 ••• ,1.1 ••• 11,.1,11 ••• 1•• 11 •• 1.1 •••• 111, •• 1•• 11.
