Specifications

ManualsBrandsECS ManualsMotherboardsA785GM-M5

Preface

This publication, including all photographs, illustrations and software, is protected

any of the material contained herein, may be reproduced without written consent of

the author.

Version 1.0

Disclaimer

The information in this document is subject to change without notice. The manufac-

turer makes no representations or warranties with respect to the contents hereof and

specifically disclaims any implied warranties of merchantability or fitness for any

particular purpose. The manufacturer reserves the right to revise this publication and

to make changes from time to time in the content hereof without obligation of the

manufacturer to notify any person of such revision or changes.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installa-

tion. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful inter-

ference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment onto an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits govern-

ing this device. Changes or modifications not expressly approved by the system’s

manufacturer could void the user’s authority to operate the equipment.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

AMD, Phenom, Athlon, Sempron and Duron are registered trademarks of AMD

Corporation.

Other product names used in this manual are the properties of their respective

owners and are acknowledged.

Summary of content (76 pages)

PAGE 1
Preface Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. Version 1.0 Disclaimer The information in this document is subject to change without notice.
PAGE 2
ii Declaration of Conformity This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: • • This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Canadian Department of Communications This class B digital apparatus meets all requirements of the Canadian Interferencecausing Equipment Regulations.
PAGE 3
iii TABLE OF CONTENTS Preface i Chapter 1 1 Introducing the Motherboard 1 Introduction............................................................................................1 Features...................................................................................................2 Motherboard Components...................................................................5 Chapter 2 7 Installing the Motherboard 7 Safety Precautions.................................................................
PAGE 4
iv Integrated Peripherals..................................................................35 Power Management Setup.............................................................37 PCI/PnP Setup..............................................................................38 PC Health Status...........................................................................39 Frequency/Voltage Control............................................................43 Load Default Settings..................................
PAGE 5
1 Chapter 1 Introducing the Motherboard Introduction Thank you for choosing the A785GM-M5 motherboard. This motherboard is a high performance, enhanced function motherboard that supports socket for AMD Phenom TM II/Phenom TM processor (socket AM2+)/Athlon TM 64 X2 Dual-Core/ AthlonTM 64/SempronTM processors for high-end business or personal desktop markets. The motherboard incorporates the AMD 785G Northbridge (NB) and SB710 Southbridge (SB) chipsets. The Northbridge supports the HyperTransportTM 3.
PAGE 6
2 Feature Processor This motherboard uses a socket AM2+/AM2 that carries the following features: • Accommodates AMD PhenomTM II/PhenomTM processor (socket AM2+)/ AMD AthlonTM 64X2 Dual-Core/AthlonTM 64/Sempron™ processors • Supports HyperTransportTM (HT) 3.0 interface speeds HyperTransportTM Technology is a point-to-point link between two devices, it enables integrated circuits to exchange information at much higher speeds than currently available interconnect technologies.
PAGE 7
3 Onboard LAN (optional) The onboard LAN controller provides either of the following features: • • • • • PCI Express base 1.1 compliant Integrated PHY for 10/100/1000 Mbps IEEE 802.3x compliant flow control support IEEE 802.3ab Auto-Negotiation support IEEE 802.3ab PHY compliance and compatibility • • • • PCI Express base 1.1 compliant Integrated PHY for 10/100 Mbps IEEE 802.3x compliant flow control support IEEE 802.
PAGE 8
4 BIOS Firmware The motherboard uses AMI BIOS that enables users to configure many system features including the following: • Power management • Wake-up alarms • CPU parameters • CPU and memory timing The firmware can also be used to set parameters for different processor clock speeds. 1. Some hardware specifications and software items are subject to change without prior notice. 2. Due to chipset limitation, we recommend that motherboard be operated in the ambiance between 0 and 50 ° C.
PAGE 9
5 Motherboard Components Introducing the Motherboard
PAGE 10
6 Table of Motherboard Components LABEL CO MPO NENTS 1. CPU Socket Socket for AMD Phenom TM II/Phenom TM processor (socket AM2+)/AMD Athlon TM 64 X2 Dual-Core/Athlon TM 64/Sempron TM processors 2. CPU_FAN CPU cooling fan connector 3. DDR2_1~2 240-pin DDR2 SDRAM slots 4. AT X_POWER Standard 24-pin AT X power connector 5. IDE Primary IDE connector 6. SAT A1~6 Serial AT A connectors 7. CLR_CMOS Clear CMOS jumper 8. F_PANEL Front panel switch/LED header 9.
PAGE 11
7 Chapter 2 Installing the Motherboard Safety Precautions • • • • • Follow these safety precautions when installing the motherboard Wear a grounding strap attached to a grounded device to avoid damage from static electricity Discharge static electricity by touching the metal case of a safely grounded object before working on the motherboard Leave components in the static-proof bags they came in Hold all circuit boards by the edges.
PAGE 12
8 Do not over-tighten the screws as this can stress the motherboard. Checking Jumper Settings This section explains how to set jumpers for correct configuration of the motherboard. Setting Jumpers Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered. When setting the jumpers, ensure that the jumper caps are placed on the correct pins. The illustrations show a 2-pin jumper. When the jumper cap is placed on both pins, the jumper is SHORT.
PAGE 13
9 Checking Jumper Settings The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled. Jumper Settings Jumper Type Description Setting (default) CLR_CMOS 3-pin CLEAR CMOS 1-2: NORMAL 2-3: CLEAR 1 Before clearing the CMOS, make sure to turn the system off. CLR_CMOS Rear USB/PS2 USBPWR_R1 3-pin Power Select Jumper 1-2: VCC 2-3: 5VSB Front Panel USBPWR_F1 3-pin USB Power Select Jumper 1-2: VCC 2-3: 5VSB 1 USBPWR_R1 1 USBPWR_F1 1.
PAGE 14
10 Installing Hardware Installing the Processor Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surfacemount resistors with the clip of the cooling fan. If the clip of the cooling fan scrapes across the motherboard, you may cause serious damage to the motherboard or its components. On most motherboards, there are small surface-mount resistors near the processor socket, which may be damaged if the cooling fan is carelessly installed.
PAGE 15
11 CPU Installation Procedure The following illustration shows CPU installation components. 1 2 3 4 5 6 Unhook the locking lever of the CPU socket. Pull the locking lever away from the socket and raising it to the upright position. Match the pin1 corner marked as the beveled edge on the CPU with the pin1 corner on the socket. Insert the CPU into the socket. Do not use force. Push the locking lever down and hook it under the latch on the edge of socket. Apply thermal grease to the top of the CPU.
PAGE 16
12 Installing Memory Modules This motherboard accommodates two memory modules. It can support two 240-pin DDR2 1066 (AM2+)/800/667/533/400. The total memory capacity is 16 GB*. DDR2 SDRAM memory module table Memory module DDR2 DDR2 DDR2 DDR2 DDR2 400 533 667 800 1066 Memory Bus 200 266 333 400 533 MHz MHz MHz MHz MHz You must install at least one module in any of the two slots. Each module can be installed with 8 GB of memory; total memory capacity is 16 GB*.
PAGE 17
13 Table A: Unbuffered DIMM Support for Socket AM2+/AM2 CPU DRAM Speed DDR2-400 DDR2-400 DDR2-533 1 1 DIMM1 DIMM2 Any Any Any Any SRx16 SRx16 DDR2-533 SRx16 SRx8 SRx8 SRx16 DDR2-533 SRx8 SRx8 DDR2-533 DRx8 DRx8 DRx8 SRx16 DDR2-533 SRx16 DRx8 DRx8 SRx8 DDR2-533 SRx8 DRx8 DDR2-667 Any SRx16 SRx16 DDR2-667 SRx16 SRx8 SRx8 SRx16 DDR2-667 SRx8 SRx8 DDR2-667 DRx8 DRx8 DRx8 SRx16 DDR2-667 SRx16 DRx8 DRx8 SRx8 DDR2-667 SRx8 DRx8 DDR2-800 Any DDR2-800 Any Any 1.
PAGE 18
14 Table B: DDR2 (memory module) QVL (Qualified Vendor List) The following DDR2 1066 (AM2+)/800/667/533/400 memory modules have been tested and qualified for use with this motherboard. Type DDR2 533 Size Vendor Module Name 512 MB Samsung PC2-4200U-4444-10-B1 1 GB A-data Vitesta 512 MB Micron 1 GB Corsair Kingston Micron MT4HTF6464AY-667E1 AU01GE667C5KBGC 78.01G9O.9K5 VS1GB667D2 KVR667D2N5 MT8HTF12864AY-667E1 AL7E8E63B-6E1T AL7E8F63J-6E1 AL7E8F73C-6E1 Golden Bar M378T2863DZS 0742 78.A1G9O.
PAGE 19
15 Type Size Vendor A-DATA Apacer CORSAIR Geil Platinum Edition HYMP125U64CP8-S6 AB KingMax KLDE88F-B8KU5 NHES 1 GB 2 GB KVR800D2N5/2G KVR800D2N6/2G-SP Micron MT16HTF25664AY-800E1 Nanya NT2GT64U8HD0BY-AD Samsung DDR2 1066 78.A1GC0.9L4 CM2X2048-6400C5 Geil PSC 4 GB 78.A1GAO.
PAGE 20
16 Expansion Slots Installing Add-on Cards The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities. With these efficient facilities, you can increase the motherboard’s capabilities by adding hardware that performs tasks that are not part of the basic system.
PAGE 21
17 Follow these instructions to install an add-on card: 1 2 3 Remove a blanking plate from the system case corresponding to the slot you are going to use. Install the edge connector of the add-on card into the expansion slot. Ensure that the edge connector is correctly seated in the slot. Secure the metal bracket of the card to the system case with a screw.
PAGE 22
18 Connecting Optional Devices Refer to the following for information on connecting the motherboard’s optional devices: F_AUDIO: Front Panel Audio header This header allows the user to install auxiliary front-oriented microphone and lineout ports for easier access.
PAGE 23
19 SATA1~6: Serial ATA connectors These connectors are used to support the new Serial ATA devices for the highest data transfer rates (3.0 Gb/s), simpler disk drive cabling and easier PC assembly. It eliminates limitations of the current Parallel ATA interface. But maintains register compatibility and software compatibility with Parallel ATA.
PAGE 24
20 LPT: Onboard parallel port header This is a header that can be used to connect to the printer, scanner or other devices.
PAGE 25
21 Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive This section describes how to install IDE devices such as a hard disk drive and a CDROM drive. About IDE Devices Your motherboard has one IDE interface. An IDE ribbon cable supporting two IDE devices is bundled with the motherboard. You must orient the cable connector so that the pin1 (color) edge of the cable corresponds to the pin 1 of the I/O port connector.
PAGE 26
22 Refer to the illustration below for proper installation: 1 2 3 Attach either cable end to the connector on the motherboard. Attach the other cable end to the SATA hard drive. Attach the SATA power cable to the SATA hard drive and connect the other end to the power supply. This motherboard supports the “Hot-Plug” function.
PAGE 27
23 Connecting I/O Devices The backplane of the motherboard has the following I/O ports: PS2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device. PS2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard. Serial Port (COM) Use the COM port to connect serial devices such as mouse or fax/modems. VGA Port Connect your monitor to the VGA port. DVI Port Connect the DVI port to connect the monitor. USB Ports Use the USB ports to connect USB devices.
PAGE 28
24 Connecting Case Components After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following: 1 2 3 4 5 6 Connect the CPU cooling fan cable to CPU_FAN. Connect the standard power supply connector to ATX_POWER. Connect the case speaker cable to SPK. Connect the case switches and indicator LEDs to the F_PANEL. Connect the system cooling fan connector to SYS_FAN. Connect the auxiliary case power supply connector to ATX12V. 1.
PAGE 29
25 CPU_FAN: FAN Power Connector Pin Signal Name Function 1 GND System Ground 2 +12V Power +12V 3 Sense Sensor 4 PWM CPU FAN control Users please note that the fan connector supports the CPU cooling fan of 1.1A~2.2A (26.4W max.) at +12V. SYS_FAN: FAN Power Connector Pin Signal Name Function 1 GND System Ground 2 +12V Power +12V 3 Sense Sensor ATX_POWER: ATX 24-pin Power Connector Pin 1 2 3 4 5 6 7 8 9 Signal Name +3.
PAGE 30
26 SPK: Internal speaker Pin Signal Name 1 2 3 4 VCC Key NC Signal Front Panel Header The front panel header (F_PANEL) provides a standard set of switch and LED headers commonly found on ATX or Micro ATX cases.
PAGE 31
27 Chapter 3 Using BIOS About the Setup Utility The computer uses the latest “American Megatrends Inc. ” BIOS with support for Windows Plug and Play. The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS. The BIOS (Basic Input and Output System) Setup Utility displays the system’s configuration status and provides you with options to set system parameters.
PAGE 32
28 Press the delete key to access the BIOS Setup Utility. CMOS Setup Utility -- Copyright (C) 1985-2005, American Megatrends, Inc. f Standard CMOS Setup f Advanced Setup f Advanced Chipset Setup f Integrated Peripherals f Power Management Setup f PCI/PnP Setup f PC Health Status fFrequency/Voltage Control Load Default Settings fSupervisor Password fUser Password Save & Exit Setup Exit Without Saving mnlk: Move Enter : Select +/-/: Value F10: Save F1:General Help F9: Optimized Defaults ESC: Exit v02.
PAGE 33
29 Using BIOS When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of the options that are available. A highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. When an option is highlighted, execute the option by pressing . Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option.
PAGE 34
30 For the purpose of better product maintenance, the manufacture reserves the right to change the BIOS items presented in this manual. The BIOS setup screens shown in this chapter are for reference only and may differ from the actual BIOS. Please visit the manufacture’s website for updated manual. Standard CMOS Setup This option displays basic information about your system. CMOS Setup Utility -- Copyright (C) 1985-2005, American Megatrends, Inc.
PAGE 35
31 LBA/Large Mode (Auto) Use this item to set the LAB/Large mode to enhance hard disk performance by optimizing the area the hard disk is visited each time. Block (Multi-Sector Transfer (Auto) If the feature is enabled, it will enhance hard disk performance by reading or writing more data during each transfer. PIO Mode (Auto) Use this item to set the PIO mode to enhance hard disk performance by optimizing the hard disk timing.
PAGE 36
32 Advanced Setup This page sets up more advanced information about your system. Handle this page with caution. Any changes can affect the operation of your computer. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
PAGE 37
33 1st/2nd/3rd Boot Device (Hard Drive/CD/DVD/Removable Dev.) Use this item to determine the device order the computer used to look for an operating system to load at start-up time. The devices showed here will be different depending on the exact devices installed on your motherboard. fHard Disk Drive (Press Enter) Scroll to this item and press to view the following screen: CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
PAGE 38
34 Advanced Chipset Setup This page sets up more advanced information about your system. Handle this page with caution. Any changes can affect the operation of your computer. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
PAGE 39
35 Integrated Peripherals This page sets up some parameters for peripheral devices connected to the system. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
PAGE 40
36 Parallel Port Mode (Normal) Use this item to select the parallel port mode. You can select Normal (Standard Parallel Port), ECP (Extended Capabilities Port), EPP (Enhanced Parallel Port), or BPP (Bi-Directional Parallel Port). Parallel Port IRQ (IRQ7) Use this item to assign IRQ to the parallel port. USB Functions (Enabled) Use this item to enable or disable the USB function. Legacy USB Support (Enabled) Use this item to enable or disable support for legacy USB devices.
PAGE 41
37 Power Management Setup This page sets up some parameters for system power management operation. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
PAGE 42
38 Resume on RTC Alarm (Disabled) The system can be turned off with a software command. If you enable this item, the system can automatically resume at a fixed time based on the system’s RTC (realtime clock). Use the items below this one to set the date and time of the wake-up alarm. You must use an ATX power supply in order to use this feature. Press to return to the main menu setting page.
PAGE 43
39 PC Health Status On motherboards support hardware monitoring, this item lets you monitor the parameters for critical voltages, temperatures and fan speeds. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
PAGE 44
40 SMART Fan Mode (Normal) This item allows you to select the fan mode (Normal, Quiet, Silent, or Manual) for a better operation environment. If you choose Normal mode, the fan speed will be auto adjusted depending on the CPU temperature. If you choose Quite mode, the fan speed will be auto minimized for quiet environment. If you choose Silent mode, the fan speed will be auto restricted to make system more quietly. If you choose Manual mode, the fan speed will be adjust depending on users’ parameters.
PAGE 45
41 CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Smart Fan Function SMART Fan Control Smart Fan Mode SMART Fan start PWM value SMART Fan start TEMP.(°C) DeltaT1 SMART Fan Slope PWM value CPU FAN Full Limit Temp mnlk: Move Enabled Silent 5 60 +3 14 PWM value/°C 68 °C Enter : Select F1:General Help +/-/: Value Help Item Normal: auto ajusts depending on the CPU temperature. Quiet: auto minimizes fan speed for quiet environment operation.
PAGE 46
42 SMART Fan Slope PWM value (8 PWM value/°C) This item is used to set the Slope Select PWM of the smart fan. CPU FAN Full Limit Temp (65°C) This item is used to set the limit temperature of the smart fan. Press to return to the PC Health Status page.
PAGE 47
43 Frequency/Voltage Control This page enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the kind of processor you have installed in your system. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. Frequency/Voltage Control Auto Detect DIMM/PCI CIK Spread Spectrum CPU Over-clocking Func.: DIMM Voltage Enabled Enabled Disabled 1.
PAGE 48
44 Load Default Settings This option opens a dialog box to ask if you are sure to install optimized defaults or not. You select [OK], and then press , the Setup Utility loads all default values; or select [Cancel], and then press , the Setup Utility does not load default values. Supervisor Password This page helps you install or change a password. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc.
PAGE 49
45 User Password This page helps you install or change a password. CMOS Setup Utility - Copyright (C) 1985-2005, American Megatrends, Inc. User Password User Password : Not Installed Help Item mnlk: Move Enter : Select +/-/: Value F10: Save ESC: Exit F1:General Help F9: Optimized Defaults User Password (Not Installed) This item indicates whether a user password has been set. If the password has been installed, Installed displays. If not, Not Installed displays.
PAGE 50
46 Updating the BIOS You can download and install updated BIOS for this motherboard from the manufacturer’s Web site. New BIOS provides support for new peripherals, improvements in performance, or fixes for known bugs. Install new BIOS as follows: 1 If your motherboard has a BIOS protection jumper, change the setting to allow BIOS flashing. 2 If your motherboard has an item called Firmware Write Protect in Advanced BIOS features, disable it. (Firmware Write Protect prevents BIOS from being overwritten.
PAGE 51
47 Chapter 4 Using the Motherboard Software About the Software DVD-ROM/CD-ROM The support software DVD-ROM/CD-ROM that is included in the motherboard package contains all the drivers and utility programs needed to properly run the bundled products. Below you can find a brief description of each software program, and the location for your motherboard version. More information on some programs is available in a README file, located in the same directory as the software.
PAGE 52
48 Setup Tab Setup Click the Setup button to run the software installation program. Select from the menu which software you want to install. Browse CD The Browse CD button is the standard Windows command that allows you to open Windows Explorer and show the contents of the support disk. Before installing the software from Windows Explorer, look for a file named README.TXT or something similar. This file may contain important information to help you install the software correctly.
PAGE 53
49 2. Click Next. The following screen appears: 3. Check the box next to the items you want to install. The default options are recommended. 4. Click Next run the Installation Wizard. An item installation screen appears: 5. Follow the instructions on the screen to install the items. 1. Drivers and software are automatically installed in sequence. Follow the onscreen instructions, confirm commands and allow the computer to restart a few times to complete the installation. 2.
PAGE 54
50 Windows Vista/7 will appear below UAC (User Account Control) message after the system restart. You must select “Allow” to install the next driver. Continue this process to complete the drivers installation. Manual Installation Insert the disk in the DVD-ROM/CD-ROM drive and locate the PATH.DOC file in the root directory. This file contains the information needed to locate the drivers for your motherboard.
PAGE 55
51 Chapter 5 Hybrid Graphics® Technology Support Hybrid Graphics® Technology The Hybrid Graphics® technology provides significant display performance boost to AMD-based systems by inserting the external PCI Express graphics card and enabling both the discrete GPU and the AMD785G graphics core to render simultaneously in Hybrid CrossFireTM mode. Follow the steps below to start the Hybrid Graphics® technology. 1.
PAGE 56
52 Note: SurroundViewTM provides the power and convenience of multiadapter, multimonitor support for computers that use a PCI-E based graphics card in conjunction with ATI integrated graphic processors. And there are two options: Disabled and PCI-E. If SurroundView TM set to Disabled, and Init Display First set to OnBoard, SurroundViewTM will be Enabled by Catalyst Control Center based on cancel the Enable CrossFireTM option.
PAGE 57
53 4. Enter Catalyst Control Center, you can see the option of CrossFireTM, click it and select Enable CrossFireTM, then Hybrid Graphics® starts. To disable Hybrid Graphics ®, please make sure to cancel Enable CrossFireTM in Catalyst Control Center firstly.
PAGE 58
54 Memo Hybrid Graphics® Technology Support
PAGE 59
55 Chapter 6 Setting Up eJIFFY Introduction eJIFFY is a fast boot program under Linux. Instead of waiting Windows O.S to start execution, eJIFFY is ready to provide users the instant enjoyment on web browsing, photo review and online chat just within several seconds after boot up. Note: According to your motherboard uses DVD or CD, the installation may different,please refer the following installation page for more detailed information. Version: 3.
PAGE 60
56 Installation and BIOS Setup DVD Activation Finish the DVD utility setup, and then set the BIOS to complete eJIFFY activation. 1. Insert ECS software utility DVD and enter below “Utilities” screen. Click eJIFFY feature item to install. 2. Follow the onscreen instructions to finish eJIFFY setup. Restart your computer after you finish.
PAGE 61
57 3. Press or click the BIOS Setup button on the post screen to enter the BIOS setup page after boot up. 4. And then enter the Advanced Setup page to enable the item ECS eJIFFY Function. Press F10 to save the configuration and exit. Restart your computer. Note: 1. eJIFFY is available in SATA/IDE/AHCI mode. It does not support RAID configuration and the onboard 34-pin floppy drives. 2. Please refer to ECS website for new eJIFFY application updates.
PAGE 62
58 CD Manually Setup You need to finish the CD installation first before setting the BIOS. 1. Insert the eJIFFY CD in the CD-ROM drive. And follow the onscreen instructions to finish the OS installation. 2. Enter My Computer to find the eJIFFY setup program. 3. Click the setup button to run the eJIFFY software installation program, restart your computer after you finish.
PAGE 63
59 4. Press or click the BIOS Setup button on the post screen to enter the BIOS setup page after boot up. 5. And then enter the Advanced Setup page to enable the item ECS eJIFFY Function. Press F10 to save the configuration and exit. Restart your computer. Note: 1. eJIFFY is available in SATA/IDE/AHCI mode. It does not support RAID configuration and the onboard 34-pin floppy drives. 2. Please refer to ECS website for new eJIFFY application updates.
PAGE 64
60 Entering eJIFFY The post screen appears within several seconds after boot up and it has three buttons on it, Operating system, eJIFFY and BIOS Setup. Click to enter the normal OS you have installed such as Windows. Click to enter eJIFFY OS. Click to set the BIOS. If you click eJIFFY, the following screen will appear. And If you make no choice it will enter the normal OS automatically after ten seconds.
PAGE 65
61 Feature Icons The following illustration shows the main feature icons that eJIFFY provides on the menu. eWeb: Firefox for web browsing/webmail and watching flash video. ePix: Photo viewing. ePal: On-line chat tool to use the most popular IMs in the world. (MSN, ICQ , AIM, etc.) Shows ePal on-line connection status. Shut Down/Restart: Ends your session and turns off the computer./Ends your session and restart the computer.. Click once to connect the storage disk to your computer.
PAGE 66
62 Usage FAQ eWeb: Firefox for web browsing/webmail and watching flash video. Q1: How to download files to hard disk through eWeb? Click on the file link directly. Then select “Save File” in the pop-up window. Note: 1. Before downloading files, please “mount” the storage devices to make sure the device is connected with eJIFFY interface. (Please refer to the usage FAQ to mount devices) 2. eWeb does not support Office Viewer/Reader/Writer format under eJIFFY interface.
PAGE 67
63 Q2: How to switch to different languages settings? Step1. Step2.
PAGE 68
64 Q3: How to save image file through eWeb? 1. Select the image you want to save and press the right key of your mouse to show the menu, then click the option “ Save Image As” from the menu. 2. Then the “Save Image” window appears. You may rename the image file in the “Name” column and save the file in a folder as the following picture shows. Rename the image file. Then select a subdirectory or click “Create Folder” to create a new folder. Select a root directory. Click here to save the image file.
PAGE 69
65 ePix: Photo viewing. Q1: How to find image files saved in hard disk through ePix? Enter the ePix window, then click the icon “Folder” located in the upper left-hand corner, then follow the path for the files you have saved to view the image files.
PAGE 70
66 Q2: How to use the fit function under slide show? 1. Click “Edit” and select “Preferences” option from the menu. 2. Click “Viewer” and choose “Keep previous zoom” in “After loading an image”. Close the window and you can use the fit function under slide show now. Note: ePix supports to view image files only. It cannot support Office Viewer or other forms beside image files. Supported image types are: BMP, JPEG, GIF (including GIF animations), PNG, TIFF, ICO and XPM.
PAGE 71
67 Mount/Unmount Disk. Q1: What does it mean for “Mount Disk”? “Mount” means to connect the storage devices to eJIFFY interface. After plugging the external device to the computer such as USB drives, a new disk icon will appear as the following picture shows. Please click the “mount” prompt on the icon. It will change to to show the device is detected successfully. Q2: What does it mean for “Unmount Disk”? “Unmount” is to safely remove the storage devices.
PAGE 72
68 Memo Setting Up eJIFFY
PAGE 73
69 Chapter 7 Trouble Shooting Start up problems during assembly After assembling the PC for the first time you may experience some start up problems. Before calling for technical support or returning for warranty, this chapter may help to address some of the common questions using some basic troubleshooting tips. a) System does not power up and the fans are not running. 1.Disassemble the PC to remove the VGA adaptor card, DDR memory, LAN, USB and other peripherals including keyboard and mouse.
PAGE 74
70 c) The PC suddenly shuts down while booting up. 1. The CPU may experience overheating so it will shutdown to protect itself. Ensure the CPU fan is working properly. 2. From the BIOS setting, try to disable the Smartfan function to let the fan run at default speed. Doing a Load Optimised Default will also disable the Smartfan. Start up problems after prolong use After a prolong period of use your PC may experience start up problems again.
PAGE 75
If fail, contact RMA CLR CMOS and restart. Yes Halt at POST screen？ Yes Check if monitor has display Yes Check if Power Supply Unit (PSU) is working Power Bu on is pressed but PC fails to start. CMOS setup error, - need to CLRCMOS. HDD problem.
PAGE 76
72 Memo Trouble Shooting