® 1/10 2WD ELECTRIC STADIUM TRUCK ECX03430T1 | ECX03430T2 INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D’UTILISATION MANUALE DI ISTRUZIONI Congratulations on your purchase of the ECX® Circuit™ Stadium Truck. This 1/10-scale model introduces you to the sport of RC driving. Herzlichen Glückwunsch zum Kauf des ECX Circuit Stadium Truck. Dieses 1/10 Scale Model öffnet Ihnen die Welt des RC Car Sports. Nous vous félicitons pour l’achat de l' ECX Circuit Stadium Truck.
EN NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit http://www.horizonhobby.com and click on the support tab for this product.
EN Wet Conditions Maintenance • Remove the battery pack(s) and dry the contacts. If you have an air compressor or a can of compressed air, blow out any water that may be inside the recessed connector housing. • Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a garden hose. Avoid rinsing the bearings and transmission. NOTICE: Never use a pressure washer to clean your vehicle.
EN QUICK START Please read the entire manual to gain a full understanding of the vehicle, fine-tuning the setup and performing maintenance. 1. Read the safety precautions found in this manual. 2. Charge a battery for the vehicle. Refer to the included charging warnings and instructions for battery charging information. 3. Install the AA batteries in the transmitter. Only use alkaline or rechargeable batteries. 4. Install the fully charged battery in the vehicle. 5.
EN TRANSMITTER CONTROLS 8 7 6 9 10 5 11 12 4 3 1. Steering Wheel Controls direction (left/right) of the model 2. Throttle Trigger Controls speed and direction (forward/brake/reverse) of the model 3. ON/OFF Switch Turns the power ON/OFF for the transmitter 4. Throttle Limiting Switch Adjusts the throttle limit from 50%, 75%, and 100% 5. TH Rate Adjusts the end point of the throttle 6. TH Trim Adjusts the throttle neutral point 7.
EN BINDING Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. The STX2® transmitter and SPMSRX200 receiver are bound at the factory. If you need to rebind, follow the instructions below. You must rebind when: • Different failsafe positions are desired e.g., when throttle or steering reversing has been changed. • Binding the receiver to a different transmitter. CHANGING THE THROTTLE LIMIT Throttle Limit Switch 1.
EN OPERATION • ALWAYS turn on your transmitter before you turn on the receiver in the vehicle. Always power off the receiver before turning your transmitter off. • ALWAYS operate your vehicle in a wide open area. Operating the vehicle in a small space or indoors can cause overheating at low speeds. Operating at low speed increases heat in the electronic speed control (ESC). Overheating can damage the vehicle and failure may result. WHEN YOU ARE FINISHED 1. Power off the ESC. 2. Disconnect the battery.
EN MAINTENANCE SETTING THE GEAR MESH The gear mesh has already been set at the factory. Setting the gear mesh is only necessary when changing motors or gears. B C You must remove the vehicle’s gear cover (A) to make this adjustment. Proper gear mesh (how the gear teeth meet) is important to the performance of the vehicle. When the gear mesh is too loose, the spur gear could be damaged by the pinion gear of the motor. If the mesh is too tight, speed could be limited and the motor and ESC will overheat.
EN SHOCK CLEANING REAR SHOCK Oil-filled shocks will require regular maintenance due to the oil breaking down or getting dirty. This maintenance should be performed after about every 3 to 5 hours of use, depending on the conditions that the vehicle is used in. FRONT SHOCK ECX1037 ECX1037 ECX1043 ECX1043 ECX1057 • Remove the shock from the vehicle. • Remove the cap from the shock body and dispose of fluid. • Disassemble the shock. Clean thoroughly with DYNE50001. Dry parts before assembly.
EN TROUBLESHOOTING GUIDE Problem Short run time Sluggish action Controls reversed Motor/ESC overheat Does not operate Poor range The system will not connect The receiver goes into failsafe mode a short distance away from the transmitter The receiver quits responding during operation Receiver and transmitter are not bound Vehicle moves forward or backward without input from user Car does not drive straight No steering or lack of steering No throttle or lack of throttle Clicking noise in transmission
EN LIMITED WARRANTY What this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase. that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.
EN WARRANTY AND SERVICE CONTACT INFORMATION Country of Purchase United States of America Horizon Hobby Contact Information Horizon Service Center (Repairs and Repair Requests) Horizon Product Support (Product Technical Assistance) servicecenter.horizonhobby.com/ RequestForm/ productsupport@horizonhobby.com 877-504-0233 websales@horizonhobby.com 800-338-4639 service@horizonhobby.
PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI RECOMMENDED ITEMS EMPFOHLENE WERKZEUGE OUTILS RECOMMANDÉS ATTREZZI CONSIGLIATI M3x25 M3x12 M3x10 9 M3x10 M3x10 M3x25 2 mm 1.5 mm 45 7 M4.3x13 11 3 4 11 20 5 7 M4.3x13 2 8 2 44 2 45 8 7 M3x18 1 12 M3x8 2 M3x12 M3x18 43 17 46 31 M3x25 M3x13 M3x12 48 M3x12 M3x12 31 M3x16 19 20 20 20 M2.5x4 16 M3x16 8 45 23 7 M4.3x13 18 3 M4.3x13 M2x8 23 21 23 2 15 2 M4.
PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI The slipper clutch can be adjusted using this locknut (ECX1060). Fully tighten the locknut, then loosen the nut two full turns. Die Rutschkupplung kann durch diese Stopmutter eingestellt werden (ECX1060). Ziehen Sie die Mutter an und drehen Sie dann volle zwei Umdrehungen zurück. Il est possible d’ajuster le sliper par action sur cet écrou de blocage (ECX1060). Veillez à serrer l’écrou de blocage à fond.
Replacement Parts / Ersatzteile / Pièces de rechange / Pezzi di ricambio Part # 1 2 Description ECX1017 ECX1028 Main Chassis Servo Saver Set Rear Suspension Mount 3 ECX1092 Set 4 ECX1050 Setscrew M3x12 (4) 5 ECX1053 Foam Block Motor Screw/Washer 6 ECX1098 Set 7 ECX1058 Ball Stud (6) 8 ECX1065 Shoulder Screw Set (8) 9 SPMSRX200 2-Ch Receiver 11 ECX1088 Battery Hold Down Front Bumper / Motor 12 ECX231000 Guard Black Wheel Ribbed Tire 13 ECX43005 (2) Front Black Wheel Spiked Tire 14 ECX43006 (2) Rear 15
Part # Description Beschreibung Description Descrizione ECX1073 DYNS1172 ECX1048 ECX1056 ECX1029 19-Tooth Pinion Gear Motor Body Clip Bushing 3x6x2.8mm (2) Top Plate 19-Tooth Pinion Gear Motor Body Clip Buchse 3x6x2.
OPTIONAL PARTS / OPTIONALE TEILE / LISTE DES OPTIONS / ELENCO PARTI OPZIONALI Part # Description Beschreibung Description Descrizione Contrôleur Tazer Sensorless Brushless 45A étanche Tazer 45A brushless ESC senza sensori WP Moteurs Tazer Brushless 1/10 4 Pôles 3300Kv SCT Set d’outils de démarrage pour ECX/VTR/HPI 1/10 2WD Cir/Ruck/Torm Set d’amortisseurs avant en aluminium 1/10 2WD Cir/Ruck/Torm - Set d’amortisseurs arrière en aluminium 1/10 2WD - Sangle universelle pour batterie 1/10 2WD Circuit -
® ECX03430T1 | ECX03430T2 www.ecxrc.com © 2018 Horizon Hobby, LLC. ECX, the ECX logo, Circuit, Dynamite, STX2, EC3, Tazer, and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc.
