® 4WD Electric torment™ 1/10 Short course Truck ECX03013 | ECX03013AU | ECX03013I Instruction Manual Bedienungsanleitung Manuel d’utilisation MANUALE di istruzioni Congratulations on your purchase of the ECX® Torment™ Short Course Truck. This 1/10-scale model introduces you to the sport of RC driving. Herzlichen Glückwunsch zum Kauf des ECX Torment Short Course Truck. Dieses 1/10 Scale Model öffnet Ihnen die Welt des RC Car Sports. Nous vous félicitons pour l’achat du ECX Torment Short Course Truck.
EN NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit http://www.horizonhobby.com and click on the support tab for this product.
EN Water-resistant Vehicle with Waterproof Electronics Your new Horizon Hobby vehicle has been designed and built with a combination of waterproof and water-resistant components to allow you to operate the product in many “wet conditions”, including puddles, creeks, wet grass, snow and even rain. While the entire vehicle is highly water-resistant, it is not completely waterproof and your vehicle should NOT be treated like a submarine.
EN Components 1. ECX® Torment™ 1/10-scale 4WD Short Course Truck 2. Spektrum™ DX2E Transmitter 3. AA (4) Batteries 4. DYN4113 2A Peak Battery Charger 5. Dynamite® Speedpack™ 8.4V Ni-MH battery (DYN1062EC) 3 4 2 1 5 Vehicle Preparations Charging the vehicle Battery 1. Connect the AC power cord to the power slot on the charger, then connect the other end of the power cord to an AC power source. 2. The Power LED and Charging LED will turn GREEN when the charger is connected to the AC power source. 3.
EN Installing Transmitter Batteries 1. Slide the panel open on the bottom of the transmitter. 2. Obey the battery plus (+) and minus (-) diagram in the transmitter to install 4 AA batteries. 3. Slide the panel closed. We recommend using only alkaline AA batteries in the transmitter. CAUTION: If using rechargeable batteries, charge only rechargeable batteries. Charging non-rechargeable batteries may cause the batteries to burst, resulting in injury to persons and/or damage to property.
EN Transmitter Controls Reverse Switch Allows you to change the direction of steering (ST. REV) and throttle (TH. REV) controls (default settings are “N” for steering and “N” for throttle). ST rate St Trim Adjust to make the vehicle drive straight with no input at the steering wheel. Adjusts the amount the front wheels move when the steering wheel is turned left or right. Steering Wheel Th Trim Adjusts the neutral point of the electronic speed control. Power Switch Power on or off the transmitter.
EN Getting Started 1. Power on the transmitter. 2. Power on the ESC. 3. Do a test of the transmitter’s control of the vehicle with the vehicle’s wheels off the ground. 4. Start driving slowly, and, if the vehicle does not go straight, adjust the steering trim dial on the transmitter. IMPORTANT: Seat the motor brushes by driving smoothly on a flat surface during use of the first battery charge. Properly seating the motor brushes will increase the life and performance of the motor.
EN OperatioN • ALWAYS turn on your transmitter before you turn on the receiver in the vehicle. Always power off the receiver before turning your transmitter off. • ALWAYS operate your vehicle in a wide open area. Operating the vehicle in a small space or indoors can cause overheating at low speeds. Operating at low speed increases heat in the electronic speed control (ESC). Overheating can damage the vehicle and failure may result. when you are finished 1. Power off the Electronic Speed Control (ESC).
EN Maintenance electronic Speed control (esc) Programming: The ESC comes with two jumpers pre-installed in the REV: ON and BATT: Ni-MH configurations. To disable reverse or change battery type to Li-Po, disconnect the jumper from the default port and connect it to the desired port. Power off the ESC, then power it back on. If the jumpers are lost or not installed, the ESC will default to REV: ON and BATT: Li-Po.
EN Shock Cleaning Oil-filled shocks will require regular maintenance due to the oil breaking down or getting dirty. This maintenance should be performed after about every 3 to 5 hours of use, depending on the conditions that the vehicle is used in. • Remove the shock from the vehicle. • Remove the cap from the shock body and dispose of fluid. • Disassemble the shock. Clean thoroughly with DYN5505. Dry parts before assembly.
EN Binding Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. The DX2E and SR201 receiver are bound at the factory. If you need to rebind, follow the instructions below. 1. With the receiver off, insert the bind plug into the BIND port on the receiver. 2. Power the receiver through any other port. The orange LED will flash continuously, indicating the receiver is in bind mode. 3.
EN limited Warranty What this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the "Product") will be free from defects in materials and workmanship at the date of purchase.
EN contact Information Country of Purchase Horizon Hobby Horizon Service Center (Repairs and Repair Requests) Horizon Product Support United States of America (Product Technical Assistance) Sales United Kingdom Service/Parts/Sales: Horizon Hobby Limited Germany Horizon Technischer Service Sales: Horizon Hobby GmbH France Service/Parts/Sales: Horizon Hobby SAS China Service/Parts/Sales: Horizon Hobby – China Contact Information servicecenter.horizonhobby.com/ RequestForm/ www.quickbase.
EN Compliance Information for the European Union AT EE IE PL IS BE BG ES FI IT LT PT RO LI NO Instructions for disposal of WEEE by users in the European Union CZ CY DE DK FR GR HR HU LU LV MT NL SE SI SK UK CH Declaration of Conformity (in accordance with ISO/IEC 17050-1) No.
