® 1.9 4WD ELECTRIC SCALE CRAWLER RTR ECX01009 | ECX01009I INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D’UTILISATION MANUALE DI ISTRUZIONI Congratulations on your purchase of the ECX® Barrage™ 1.9 4WD Electric Scaler. This model introduces you to the sport of RC driving. Herzlichen Glückwunsch zum kauf des ECX Barrage 1.9 4WD Electric Scaler. Dieses Modell ist der gelungende Einstieg in die Welt des RC Cars Sports. Nous vous félicitons pour l’achat de l’ECX Barrage 1,9 4WD électrique.
EN NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit http://www.horizonhobby.com and click on the support tab for this product.
EN Wet Conditions Maintenance • Remove the battery pack(s) and dry the contacts. If you have an air compressor or a can of compressed air, blow out any water that may be inside the recessed connector housing. • Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a garden hose. Avoid rinsing the bearings and transmission. NOTICE: Never use a pressure washer to clean your vehicle.
EN QUICK START Please read the entire manual to gain a full understanding of the vehicle, fine-tuning the setup and performing maintenance. 1. Read the safety precautions found in this manual. 2. Charge a battery for the vehicle. Refer to the included charging warnings and instructions for battery charging information. 3. Install the AA batteries in the transmitter. Only use alkaline or rechargeable batteries. 4. Install the fully charged battery in the vehicle. 5.
EN INSTALLING THE BATTERY 1. 2. 3. 4. Remove the vehicle body. Install a fully charged battery. Secure the battery pack using the hook and loop straps. Connect the battery pack to the ESC power connector. CAUTION: Connecting the battery to the ESC with reversed polarity will cause damage to the ESC, the battery or both. Damage caused by incorrectly connecting the battery is not covered under warranty.
EN BINDING The included transmitter and receiver are bound at the factory. If you need to rebind, follow the instructions below. 1. Power off the transmitter and ESC. 2. Connect a fully charged battery pack to the ESC. 3. Power on the ESC. The RED LED on the receiver flashes. 4. Press and release the bind button (A) on the receiver. The RED LED on the receiver flashes rapidly. 5. Power on the transmitter. 6. The RED LED on the receiver turns solid when the radio system is bound.
EN OPERATION • ALWAYS turn on your transmitter before you turn on the receiver in the vehicle. Always power off the receiver before turning your transmitter off. • ALWAYS operate your vehicle in a wide open area. Operating the vehicle in a small space or indoors can cause overheating at low speeds. Operating at low speed increases heat in the electronic speed control (ESC). Overheating can damage the vehicle and failure may result. WHEN YOU ARE FINISHED 1. Power off the ESC. 2.
EN MAINTENANCE SETTING THE GEAR MESH B The gear mesh has already been set at the factory. Setting the gear mesh is only necessary when changing motors or gears. You must remove the vehicle’s gear cover (A) to make this adjustment. C Proper gear mesh (how the gear teeth meet) is important to the performance of the vehicle. When the gear mesh is too loose, the spur gear could be damaged by the pinion gear of the motor. If the mesh is too tight, speed could be limited and the motor and ESC will overheat.
EN TROUBLESHOOTING GUIDE Problem Short Run Time Sluggish Action Controls Reversed Motor/ESC overheat Does Not Operate Poor Range The system will not connect The receiver goes into failsafe mode a short distance away from the transmitter The receiver quits responding during operation Receiver and transmitter are not bound Vehicle moves forward or backward without input from user Car does not drive straight No steering or lack of steering Possible Cause Battery damaged/not charged Motor dirty Motor dirty
EN LIMITED WARRANTY What this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase. that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.
EN WARRANTY AND SERVICE CONTACT INFORMATION Country of Purchase United States of America Horizon Hobby Contact Information Horizon Service Center (Repairs and Repair Requests) Horizon Product Support (Product Technical Assistance) servicecenter.horizonhobby.com/ RequestForm/ productsupport@horizonhobby.com 877-504-0233 websales@horizonhobby.com 800-338-4639 service@horizonhobby.
Replacement Parts / Ersatzteile / Pièces de rechange / Pezzi di ricambio Part # Description Beschreibung Description Descrizione DYNS1209 Tazer 370 motor Motor: Tazer 370 Moteur: Tazer 370 Motore: Tazer 370 DYNS2210 WP 60A Bürstenregler Vorwärts/rückwärts WP 60A FWD/REV Brushed ESC WP 60A Contrôleur à balais avant/ arrière WP 60A ESC con spazzole avanti/ indietro ECX1015 5x10x4mm Ball Bearing (8) Kugellager 5x10x4mm (8) Roulements 5x10x4mm (8) Cuscinetto a sfere 5x10x4mm (8) ECX13002 2.
Replacement Parts / Ersatzteile / Pièces de rechange / Pezzi di ricambio Part # Description Beschreibung Description Descrizione ECX214012 Lower Link (2): 1.9 Barrage Unterlenker (2): 1.9 Barrage 1.9 Barrage: Tirant inférieur (2) Collegamento inferiore (2): 1.9 Barrage ECX214013 Upper Link (2): 1.9 Barrage Oberlenker (2): 1.9 Barrage 1.9 Barrage: Tirant supérieur (2) Collegamento superiore (2): 1.
42 SPMS602 ECX216003 ECX216003 ECX216003 SPMS602 ECX211021 ECX13003 ECX211014 ECX216003 ECX211018 ECX216003 ECX216003 ECX211019 ECX216003 ECX211021 DYNS2210 ECX216003 ECX212021 ECX216003 ECX213002 ECX211014 ECX211014 ECX211015 ECX211018 ECX216003 ECX216003 ECX214012 ECX216003 ECX216003 ECX216003 ECX216003 ECX216003 ECX216003 ECX211018 ECX211019 ECX216003 ECX216003 ECX216003 ECX211020 ECX211015 ECX211019 ECX216003 ECX211016 ECX216003 ECX216003 ECX216003 ECX211018
PARTS DIAGRAM | EXPLOSIONSZEICHNUNG | VUE ÉCLATÉE DES PIÈCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI FRONT AXLE | VORDERACHSE | HINTERACHSE | ASSE ANTERIORE ECX211009 ECX216003 ECX212020 ECX216003 ECX212010 ECX217001 ECX212026 ECX217001 ECX217001 ECX212026 ECX216003 ECX212025 ECX212009 ECX216003 ECX216003 ECX216003 ECX217001 ECX214010 ECX212028 ECX217001 ECX214011 ECX216003 ECX212027 ECX212027 ECX216003 ECX217001 ECX216003 ECX212024 ECX212027 ECX212024 ECX216003 REAR AXLE | ESSIEU A
® ECX01009 | ECX01009I www.ecxrc.com © 2017 Horizon Hobby, LLC. ECX, the ECX logo, Barrage, Dynamite, Speedpack, Prophet, Tazer, EC3, and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. Patents Pending. Updated 04/2017 52321.