Datasheet of ED-GW1303S V1.20211111 ED-GW1303S REV1.0 LORAWAN GATEWAY MODULE SX1303 + SX1250, MINI PCIE, SPI, US915 / EU868 2021-11-11 EDA TECHNOLOGY CO.,LTD EDA Technology Co.
Datasheet of ED-GW1303S V1.20211111 Copyright Statement: ED-GW1303S and its related intellectual property are owned by EDA Technology Co.,LTD. EDA Technology Co.,LTD has the copyright of this document and reserves all rights. Any part of the document should not be modified, distributed or duplicated in any approach and form with the written permission issued by EDA Technology Co.,LTD. Disclaimer: EDA Technology Co.
Datasheet of ED-GW1303S V1.20211111 Revision History Date 2021-11-11 Version Description Draft Initial release. Note EDA Technology Co.
Datasheet of ED-GW1303S V1.20211111 Contents Copyright Statement: ....................................................................................................................................................ii Disclaimer: ....................................................................................................................................................................ii Revision History ..................................................................................................
Datasheet of ED-GW1303S V1.20211111 Chapter 1 Overview ED-GW1303S module is a new generation of LoRaWAN gateway module in mini-PCIe form-factor with SPI interfaces based on Semtech® SX1303 and SX1250. It features extremely low power consumption, outstanding performance with CE, FCC certified.
Datasheet of ED-GW1303S V1.20211111 1.3 Interface Diagram EDA Technology Co.
Datasheet of ED-GW1303S V1.20211111 1.4 Block Diagram EDA Technology Co.
Datasheet of ED-GW1303S V1.20211111 Chapter 2 Interfaces 2.1 Pinout EDA Technology Co.
Datasheet of ED-GW1303S V1.20211111 2.2 Power Pin Name Pin ID GND 4,9,15,18,21,26,27,29,34,35,37,40,43,50 3.3V 2,24,39,41,52 Pin Type Description PI Power In The power in voltage of ED-GW1303S is 3.3V. Under TX mode, the max current can be 400mA. 2.3 SPI Interface Pin Name Pin ID Pin Type Description SX_CLK 45 DI SPI Clock SX_MISO 47 DO SPI MISO SX_MOSI 49 DI SPI MOSI SX_CSN 51 DI SPI CS 2.
Datasheet of ED-GW1303S V1.20211111 2.4.3 RX_ON When receive is enabled, the RX_ON signal will output HIGH, and the RX LED will on. 2.4.4 TX_ON When transmit is enabled, the TX_ON signal will output HIGH, and the TX LED will on. 2.4.5 CFG_ON When the module is configurated successful, the CFG_ON signal will output HIGH, and the CFG LED will on. 2.5 Antenna Connector The Antenna connector is compatible with I-PEX 1 standard. EDA Technology Co.
Datasheet of ED-GW1303S V1.20211111 Chapter 3 Electrical Characteristics 3.1 Power Parameter Description Min Type Max Unit VCC Power In 3.0 3.3 3.6 V 3.2 IO Parameter Description Min Max Unit VIH Input High Voltage 0.7 * VCC VCC + 0.3 V VIL Input Low Voltage -0.3 0.3 * VCC V VOH Output High Voltage VCC – 0.5 VCC V VOL Output Low Voltage 0 0.4 V 3.
Datasheet of ED-GW1303S V1.20211111 Chapter 4 Dimension EDA Technology Co.
Datasheet of ED-GW1303S V1.20211111 Chapter 5 Contact ⚫ Email – sales@edatec.cn / support@edatec.cn ⚫ Mobile – +86-18621560183 ⚫ Website – https://www.edatec.cn ⚫ Address – Room 301, Building 24, No. 1661, Jialuo Road, Jiading District, Shanghai 5.1 About EDATEC EDA Technology Co.,Ltd is located in Shanghai, it is one of Raspberry Pi’s Global Design Partners.
Peripheral Design Requirement List of applicable FCC rules: FCC Part15 Subpart C, Section 15.247 Specific operational use conditions The information in this article, including the URL for reference, if there is any change, without prior notice.
Installation Notice The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module.
the host equipment is no longer considered valid and the FCC ID of the module cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Antennas The module doesn’t have onboard antenna, but has an antenna connector which is compatible with I-PEX 1 standard.
diversity architecture). For the test results, only the worst case was shown in test report. RADIATED EMISSION TEST (ABOVE 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates, XYZ axis and antenna ports (if EUT with antenna diversity architecture). Additional testing Part 15 Subpart B disclaimer The grantee should include a statement that the modular transmitter is only FCC authorized for the specific rule parts (i.e.
