E-MPS-I-0612 Operator’s Instruction Manual Concrete/Asphalt Saws SB-14 ASB-14 SK-14 DS-18 Electric, Gasoline and Pneumatic Models SK-10 Manual - Portable 100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA Phone (301) 663-1600 • 1-800-638-3326 Fax (301) 663-1607 • 1-800-447-3326 Website: www.edcoinc.com Email: sales@edcoinc.
E-MPS-I-0612 READ AND UNDERSTAND THE OPERATORS INSTRUCTION MANUAL THOROUGHLY BEFORE ATTEMPTING TO OPERATE THIS EQUIPMENT. Death or serious injury could occur if this machine is used improperly. SAFETY MESSAGES SAFETY MESSAGES • Safety Instructions are proceeded by a graphic alert symbol of DANGER, WARNING, or CAUTION. Indicates an imminent hazard which, if not avoided, will result in death or serious injury. Indicates an imminent hazard which, if not avoided, can result in death or serious injury.
E-MPS-I-0612 Operators Instruction Manual Table of Contents Section Page Number Operating Controls........................................................................................................4 Operating Instructions................................................................................................5-7 Optional Accessories.....................................................................................................7 Maintenance Instructions....................................
E-MPS-I-0612 Operating Controls Gasoline Powered Please Note: ( DS-18 SHOWN) Engine Stop Switch Depth Control Handwheel Knob Throttle Control Lifting Bail Controls shown are for the model indicated. The location of these controls may vary on the different models. Due to improvements and changes in the equipment, the illustration shown may be different from the actual machine.
E-MPS-I-0612 Operating Instructions • Read and understand all operating instructions before operating this equipment. Death or serious injury can result if this machine is used improperly. • Concrete saws are designed to be used to cut flat horizontal concrete or asphalt slabs using • • • diamond saw blades. The machines may be equipped with gasoline engines or electric motors. They are designed to be controlled by a single operator from a position at the rear of the saw.
E-MPS-I-0612 Operating Instructions • FOR WET CUTTING: Attach the water supply. A flow rate of approximately 2 gallons per minute (minimum) is required. Attach the water hose to the coolant valve. Use the valve to control the flow of water. • FOR DRY CUTTING: Provide a respirator and dust control system. • FOR ELECTRIC MODELS: Be sure the “OFF” button is depressed. Hook up the electrical power source by plugging into the connector provided.
E-MPS-I-0612 Operating Instructions • TO STOP THE MACHINE: Stop forward motion. On gasoline models push the throttle to idle. Turn the depth control handwheel knob counter clockwise to raise the blade clear of the cut. Turn ignition or power switch off and let the engine come to a complete stop. Turn off the water supply. • WHEN MANEUVERING THE SAW: Make sure the blade is raised high enough so it does not strike the slab surface.
E-MPS-I-0612 Maintenance Instructions Disconnect the machine from the power source. Remove the spark plug lead on gasoline engine models or disconnect the supply voltage connector on electric models, before performing any maintenance. All maintenance to be performed regularly by qualified personnel. • Never work under saw without first placing chocks on the wheels and support device under the saw to prevent it from moving or falling. Always work on a flat and level surface.
E-MPS-I-0612 Changing Blades (On EDCO saws listed in this manual) Disconnect the machine from the power source before performing any work on the equipment (i.e. changing the blade). To disconnect the power source on gasoline engine models, remove the spark plug lead. On electric models, unplug the electrical power cord at the machine. • Make sure you have the proper blade for the job. Determine the hardness and composition of the slab.
E-MPS-I-0612 Lubrication Points Grease Bearings Every 4 Hours of Use NOTE: Wipe grease fittings clean before servicing. MODEL SK-14 GREASE FITTINGS MODEL SK-10 GREASE FITTINGS MODEL SB-14 ASB-14 GREASE FITTINGS MODEL DS-18 GREASE FITTINGS Printed in USA 100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA Phone (301) 663-1600 • 1-800-638-3326 ©2012 TVW Fax (301) 663-1607 • 1-800-447-3326 Page 10 Website: www.edcoinc.com Email: sales@edcoinc.
E-MPS-I-0612 Repairs are to be preformed by EDCO or by approved EDCO repair technicians. Read and follow all instructions in the Engine Manufacturer’s Owner’s Manual.
E-MPS-I-0612 LIMITED EQUIPMENT WARRANTY OF SALE – TERMS & CONDITIONS Equipment Development Company, Inc. herein referred to as EDCO (Seller) warrants that each new unit manufactured by EDCO to be free from defects in material and workmanship in normal use and service for a period of (1) one year (except for the cutter drum assembly on all model concrete/asphalt planes, in which case the warranty period shall be 90 days) from date of shipment to the original retail or equipment rental center owner.