Corporation Automobile Parts User Manual

MANIFOLD
ASSEMBLY CONTENTS
Catalog #3562, 3563, 3564, 3565
Rev. 3/06 Page 2 of 16
©2006 Edelbrock Corporation
Brochure #63-0047
Qty. Description
❑ 1 Manifold assembly (see detail below)
❑ 1 Installation instructions
❑ 1 EPROM adapter circuit board (#3562 only)
❑ 1 Fuel injector wiring harness
❑ 1 Fuel filter adapter fitting (filter to #6 AN male) with O-ring
❑ 1 Return line adapter fitting
❑ 2 #6 AN straight pushlock fittings
❑ 1 3/8" i.d. pushlock heat resistant fuel line, 10 foot length
❑ 1 #6 AN 45 degree elbow pushlock fitting
❑ 1 #6 AN 90 degree elbow pushlock fitting
❑ 1 Fuel line clamp (floor mounted)
❑ 4 11" tie wrap
❑ 1 Throttle cable bracket
❑ 1 Throttle body block-off plate
❑ 1 Throttle body gasket
❑ 1 EGR gasket
❑ 1 3/8" NPT pipe plug
❑ 1 3/8” I.D. Flatwasher
Qty
. Description
❑ 1 3/8" NPT male to 3/8” NPT female 90 Degree elbow
❑ 1 3/8" NPT to 1/2” hose brass fitting
❑ 1 2 foot length 15/32 i.d vacuum line (power brakes)
❑ 1 6” length 3/8’ fuel line (breather line extension)
❑ 1 1/2" NPT to 3/4" hose barb
❑ 1 36" length 3/4" i.d. heater hose
❑ 1 3" length 5/16" i.d. high pressure fuel line (pump to sending
unit)
❑ 1 2 foot length 5/32" i.d. vacuum line (regulator & EGR)
❑ 1 5-1/8" i.d. air cleaner base gasket
❑ 1 12" length 1/4" i.d. vacuum line (MAP)
❑ 1 1/2” hose clamps
❑ 2 3/4" hose clamp
❑ 1 3/8" hose clamp (fuel injection clamp)
❑ 1 5/16" hose clamp (fuel injection clamp)
❑ 1 1/4" x 1/4" out x 5/32" bottom out vacuum “T” fitting
❑ 1 10-16 x 3/4" TEX screw (self tapping)
❑ 1 Air Cleaner Lid decal
PERFORMER MULTI-POINT EFI
KIT CONTENTS
Qty
. Description
❑ 1 Intake manifold
❑ 1 Driver’s side (left side) fuel rail
❑ 1 Passenger’s side (right side) fuel rail
❑ 4 1/4"-20 x 1.25" Hex head cap screw rail hold down bolts
❑ 1 Fuel pressure regulator
❑ 8 Magnetti Marelli
®
pico injectors
❑ 1 Fuel crossover line (including adapter and schrader valve)
❑ 1 Fuel inlet fitting (3/8" male pipe to #6 AN male, steel)
Qty
. Description
❑ 1 Fuel regulator nut and Viton O-ring
❑ 1 Viton O-ring; fuel regular nut (1/2" o.d. 5/16" i.d.)
❑ 4 1/4" i.d. AN thin flat washers
❑ 1 1/4"-20 x 1/2" hex head cap screw
❑ 1 1/4" i.d. split lock washer
❑ 1 Schrader valve cap
❑ 4 1/4" internal star lock washers
SUGGESTED TOOLS AND MATERIALS FOR INSTALLATION
❑ 3/8" ratchet socket set with extensions
❑ Combination set of open-end wrenches (SAE and metric)
❑ Jackstands, screwdrivers, pliers, crescent wrench, hacksaw,
hammer, brass punch and assorted hand tools
❑ Torx screwdrivers
❑ Tin snips
❑ White grease
❑ Teflon thread sealant or equivalent
❑ Intake gasket set (Edelbrock #7205, GM #10181398, or
equivalent)
❑ Thermostat housing gasket (GM #10105135, Fel-Pro #2201, or
equivalent)
❑ Gasket sealant (Gasgacinch, etc.)
❑ RTV Silicone sealant; O2 sensor-safe
❑ Wire stripper & crimper
❑ Heat gun or lighter