ELECTRICFLAT PANEL FIREPLACE HEATER ! OWNERS MANUAL MODEL #: 101004,111004, 101005, 111005 36"/50"/60"/72"Wall Mounted / Built-in Electric Fireplace AC 120V 60Hz 1500W WARNING Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in fire, electric shock, or serious personal injury. CAUTION Keep this owner’s manual for future reference.
IMPORTANT SAFETY INFORMATION! WARNING ⚫ Read all instructions before using this heater! ⚫ This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater, and keep them away from the sides and rear.
⚫ ALWAYS turn this heater off before unplugging it from the outlet. ⚫ ALWAYS disconnect this unit from the power supply before performing any assembly or cleaning, or before relocating the electric fireplace. ⚫ NEVER leave this heater unattended. ALWAYS unplug this heater when not in use. ⚫ ALWAYS store this heater in a dry location. NEVER use the fireplace if it has become wet. ⚫ NEVER plug this heater into an outlet that is old, cracked, or has any loose wires or connections.
Parts and Hardware A – Fireplace E-Wall Bracket Fixed on back of firebox F-Decorative Pebbles B – Wood Screws C – Drywall anchors Remote Control D - Metal Bracket G-Decorative Crystals H - Log set I - Plastic Tray Specification and Dimension Description Type Voltage Watts Amps Electric Fireplace 3 Way Mounting Unit Wall-Mount, Recess Wall and Assemble with mantel 120V AC into MAX 1500W 15 AMP Grounded Circuit PRODUCT DIMENSIONS Model Number BG-36B BG-50B BG-60B BG-72B A B C D E F G 3
MINIMUM CLEARANCE TO COMBUSTIBLES Measurements are taken from the glass front. Bottom Sides Back 0" 0" 0" Top Top 8" (300mm) to mantel 8" (300mm) to ceiling MINIMUM MANTEL CLEARANCES WARNING WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR LACQUER MUST BE HEAT RESISTANT TO PREVENT DISCOLOURATION.
RECESSED TO WALL INSTALLATION W H Hole Size (A) (B) STEP A. Selection a dry wall to open a hole for fireplace box. Size of hole as below chart Figure ( A ) Framing Hole Size Model Number W H BG-36B 33” (83.82CM) 20.75” (52.71CM) BG-50B 47” (119.38CM) 20.75” (52.71CM) BG-60B 47” (119.38CM) 20.75” (52.71CM) BG-72B 69” (175.26CM) 20.75” (52.71CM) STEP B. Fix the three wall anchors in each side of the fireplace box according to the dimensions showed on the drawing.
(C) (D) STEP C. Take off the two screws in both sides of the glass panel. Figure ( C ) STEP D. Have two person to take the glass panel out of the fireplace box. Place it to a soft and clean place. Figure ( D) (E) (F) (G) STEP E. Have two person to move the fireplace box to the wall hole.
Wall Mounted Installation Due to the many different materials used on different walls, it is highly recommended that you consult your local builder before you install this appliance on the wall. A.Select a location that is not prone to moisture and is located at least 36" (914mm) away from combustible materials such as curtain drapes, furniture, bedding, paper, etc. B.Have two people hold the appliance against the wall to determine the final location. C.Place unit face down on a soft, non abrasive surface.
BG-72B Wall Bracket Illustrated HARD WIRING INSTALLATION WARNING TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE. HARD WIRING CONNECTION If it is necessary to hard wire this appliance, a qualified electrician must remove the cord connection, and wire the appliance directly to the house hold wiring. This appliance must be electrically connected and grounded in accordance with local codes, if hard wired.
A. Remove the cover plate from the right side B. Remove the wire connectors from the power bottom of the appliance by removing the three cord. The power cord may be discarded. screws, as shown above. C. Take the new cover plate, supplied in the hardware bag. Punch out the 7/8" (22.2mm) hole and install a box connector through, into the junction box. Snap the box connector clamp onto the supply wires. D.
Figure 1. Figure 2. Figure 3. (Crystal medias) Figure 3. (Pebbles medias) Operation Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in electric shock, fire, serious injury, or death. Power Plug the power cord into a 110~120 Volt 15 Amp grounded outlet (see IMPORTANT SAFETY INFORMATION on Pages 2 and 3). Make sure the outlet is in good condition and that the plug is not loose.
Before operating, please review the IMPORTANT SAFETY INFORMATION on Pages 2 and 3, and heed all warnings. Control Panel Remote control Touch Panel Control Panel / Touch Panel / Remote Control Operation BUTTON FUNCTION ACTION & INDICATION ON: Enables control panel functions and remote control. Turns on flame effect. OFF: Disables control panel functions and POWER remote control. Turns off flame effect. TIMER button: Controls timer settings to turn off fireplace at selected time.
HEATER button: Turns heater on and off. NOTE: The heater only works when the flame effect is on. If the flame effect is off, the heater will not turn on. NOTE: To prevent overheating, the heater HEATER fan will blow cool air for 8-10 seconds before the heater turns on, and after the heater turns off. 1. Press once. Indicator lights up. Fan blows cool air for 10 seconds. 750W heater turns on and blows warm air. 2. Press again. Indicator lights up. 1500W heater turns on and blows hot air. 3. Press again.
Care and Maintenance Cleaning ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in electric shock, fire, or personal injury. NEVER immerse in water or spray with water. Doing so could result in electric shock, fire, or personal injury. Metal: • Buff using a soft cloth, slightly dampened with a citrus oil-based product.
Limited Warranty J & J Global (Seller) warrants to the original Buyer only, that each product will be free from defects in material and workmanship for a period of one (1) year from date of purchase. SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP.