Installation guide
Table Of Contents
- Chapter 1: Introduction
- Chapter 2: Initial Configuration
- Chapter 3: Configuring the Switch
- Using the Web Interface
- Navigating the Web Browser Interface
- Panel Display
- Main Menu
- Basic Configuration
- Displaying System Information
- Displaying Switch Hardware/Software Versions
- Displaying Bridge Extension Capabilities
- Setting the Switch’s IP Address
- Enabling Jumbo Frames
- Managing Firmware
- Saving or Restoring Configuration Settings
- Console Port Settings
- Telnet Settings
- Configuring Event Logging
- Resetting the System
- Setting the System Clock
- Simple Network Management Protocol
- User Authentication
- Configuring User Accounts
- Configuring Local/Remote Logon Authentication
- Configuring Encryption Keys
- AAA Authorization and Accounting
- Configuring HTTPS
- Replacing the Default Secure-site Certificate
- Configuring the Secure Shell
- Configuring Port Security
- Configuring 802.1X Port Authentication
- Web Authentication
- Network Access - MAC Address Authentication
- MAC Authentication
- Access Control Lists
- Port Configuration
- Address Table Settings
- Spanning Tree Algorithm Configuration
- VLAN Configuration
- Link Layer Discovery Protocol
- Class of Service Configuration
- Quality of Service
- VoIP Traffic Configuration
- Multicast Filtering
- Multicast VLAN Registration
- DHCP Snooping
- IP Source Guard
- IP Clustering
- UPnP
- Chapter 4: Command Line Interface
- Using the Command Line Interface
- Entering Commands
- Command Groups
- Line Commands
- General Commands
- System Management Commands
- Flash/File Commands
- Authentication Commands
- Access Control List Commands
- SNMP Commands
- Interface Commands
- Mirror Port Commands
- Rate Limit Commands
- Link Aggregation Commands
- Address Table Commands
- LLDP Commands
- lldp
- lldp holdtime-multiplier
- lldp medFastStartCount
- lldp notification-interval
- lldp refresh-interval
- lldp reinit-delay
- lldp tx-delay
- lldp admin-status
- lldp notification
- lldp mednotification
- lldp basic-tlv management-ip-address
- lldp basic-tlv port-description
- lldp basic-tlv system-capabilities
- lldp basic-tlv system-description
- lldp basic-tlv system-name
- lldp dot1-tlv proto-ident
- lldp dot1-tlv proto-vid
- lldp dot1-tlv pvid
- lldp dot1-tlv vlan-name
- lldp dot3-tlv link-agg
- lldp dot3-tlv mac-phy
- lldp dot3-tlv max-frame
- lldp dot3-tlv poe
- lldp medtlv extpoe
- lldp medtlv inventory
- lldp medtlv location
- lldp medtlv med-cap
- lldp medtlv network-policy
- show lldp config
- show lldp info local-device
- show lldp info remote-device
- show lldp info statistics
- UPnP Commands
- Spanning Tree Commands
- spanning-tree
- spanning-tree mode
- spanning-tree forward-time
- spanning-tree hello-time
- spanning-tree max-age
- spanning-tree priority
- spanning-tree pathcost method
- spanning-tree transmission-limit
- spanning-tree mst-configuration
- mst vlan
- mst priority
- name
- revision
- max-hops
- spanning-tree spanning-disabled
- spanning-tree cost
- spanning-tree port-priority
- spanning-tree edge-port
- spanning-tree portfast
- spanning-tree link-type
- spanning-tree loopback-detection
- spanning-tree loopback-detection release-mode
- spanning-tree loopback-detection trap
- spanning-tree mst cost
- spanning-tree mst port-priority
- spanning-tree protocol-migration
- show spanning-tree
- show spanning-tree mst configuration
- VLAN Commands
- Priority Commands
- Quality of Service Commands
- Voice VLAN Commands
- Multicast Filtering Commands
- Multicast VLAN Registration Commands
- IP Interface Commands
- IP Source Guard Commands
- DHCP Snooping Commands
- IP Cluster Commands
- Appendix A: Software Specifications
- Appendix B: Troubleshooting
- Glossary
- Index
Command Line Interface
4-162
4
snmp-server user
This command adds a user to an SNMP group, restricting the user to a specific
SNMP Read, Write, or Notify View. Use the no form to remove a user from an SNMP
group.
Syntax
snmp-server user username groupname [remote ip-address] {v1 | v2c | v3
[encrypted] [auth {md5 | sha} auth-password [priv des56 priv-password]]
no snmp-server user username {v1 | v2c | v3 | remote}
• username - Name of user connecting to the SNMP agent.
(Range: 1-32 characters)
• groupname - Name of an SNMP group to which the user is assigned.
(Range: 1-32 characters)
• remote - Specifies an SNMP engine on a remote device.
• ip-address - The Internet address of the remote device.
• v1 | v2c | v3 - Use SNMP version 1, 2c or 3.
• encrypted - Accepts the password as encrypted input.
• auth - Uses SNMPv3 with authentication.
• md5 | sha - Uses MD5 or SHA authentication.
• auth-password - Authentication password. Enter as plain text if the
encrypted option is not used. Otherwise, enter an encrypted password.
(A minimum of eight characters is required.)
• priv des56 - Uses SNMPv3 with privacy with DES56 encryption.
• priv-password - Privacy password. Enter as plain text if the encrypted
option is not used. Otherwise, enter an encrypted password.
Table 4-45 show snmp group - display description
Field Description
groupname Name of an SNMP group.
security model The SNMP version.
readview The associated read view.
writeview The associated write view.
notifyview The associated notify view.
storage-type The storage type for this entry.
Row Status The row status of this entry.