Installation guide
Table Of Contents
- Chapter 1: Introduction
- Chapter 2: Initial Configuration
- Chapter 3: Configuring the Switch
- Using the Web Interface
- Navigating the Web Browser Interface
- Panel Display
- Main Menu
- Basic Configuration
- Displaying System Information
- Displaying Switch Hardware/Software Versions
- Displaying Bridge Extension Capabilities
- Setting the Switch’s IP Address
- Enabling Jumbo Frames
- Managing Firmware
- Saving or Restoring Configuration Settings
- Console Port Settings
- Telnet Settings
- Configuring Event Logging
- Resetting the System
- Setting the System Clock
- Simple Network Management Protocol
- User Authentication
- Configuring User Accounts
- Configuring Local/Remote Logon Authentication
- Configuring Encryption Keys
- AAA Authorization and Accounting
- Configuring HTTPS
- Replacing the Default Secure-site Certificate
- Configuring the Secure Shell
- Configuring Port Security
- Configuring 802.1X Port Authentication
- Web Authentication
- Network Access - MAC Address Authentication
- MAC Authentication
- Access Control Lists
- Port Configuration
- Address Table Settings
- Spanning Tree Algorithm Configuration
- VLAN Configuration
- Link Layer Discovery Protocol
- Class of Service Configuration
- Quality of Service
- VoIP Traffic Configuration
- Multicast Filtering
- Multicast VLAN Registration
- DHCP Snooping
- IP Source Guard
- IP Clustering
- UPnP
- Chapter 4: Command Line Interface
- Using the Command Line Interface
- Entering Commands
- Command Groups
- Line Commands
- General Commands
- System Management Commands
- Flash/File Commands
- Authentication Commands
- Access Control List Commands
- SNMP Commands
- Interface Commands
- Mirror Port Commands
- Rate Limit Commands
- Link Aggregation Commands
- Address Table Commands
- LLDP Commands
- lldp
- lldp holdtime-multiplier
- lldp medFastStartCount
- lldp notification-interval
- lldp refresh-interval
- lldp reinit-delay
- lldp tx-delay
- lldp admin-status
- lldp notification
- lldp mednotification
- lldp basic-tlv management-ip-address
- lldp basic-tlv port-description
- lldp basic-tlv system-capabilities
- lldp basic-tlv system-description
- lldp basic-tlv system-name
- lldp dot1-tlv proto-ident
- lldp dot1-tlv proto-vid
- lldp dot1-tlv pvid
- lldp dot1-tlv vlan-name
- lldp dot3-tlv link-agg
- lldp dot3-tlv mac-phy
- lldp dot3-tlv max-frame
- lldp dot3-tlv poe
- lldp medtlv extpoe
- lldp medtlv inventory
- lldp medtlv location
- lldp medtlv med-cap
- lldp medtlv network-policy
- show lldp config
- show lldp info local-device
- show lldp info remote-device
- show lldp info statistics
- UPnP Commands
- Spanning Tree Commands
- spanning-tree
- spanning-tree mode
- spanning-tree forward-time
- spanning-tree hello-time
- spanning-tree max-age
- spanning-tree priority
- spanning-tree pathcost method
- spanning-tree transmission-limit
- spanning-tree mst-configuration
- mst vlan
- mst priority
- name
- revision
- max-hops
- spanning-tree spanning-disabled
- spanning-tree cost
- spanning-tree port-priority
- spanning-tree edge-port
- spanning-tree portfast
- spanning-tree link-type
- spanning-tree loopback-detection
- spanning-tree loopback-detection release-mode
- spanning-tree loopback-detection trap
- spanning-tree mst cost
- spanning-tree mst port-priority
- spanning-tree protocol-migration
- show spanning-tree
- show spanning-tree mst configuration
- VLAN Commands
- Priority Commands
- Quality of Service Commands
- Voice VLAN Commands
- Multicast Filtering Commands
- Multicast VLAN Registration Commands
- IP Interface Commands
- IP Source Guard Commands
- DHCP Snooping Commands
- IP Cluster Commands
- Appendix A: Software Specifications
- Appendix B: Troubleshooting
- Glossary
- Index
Interface Commands
4-175
4
Example
show interfaces switchport
This command displays the administrative and operational status of the specified
interfaces.
Syntax
show interfaces switchport [interface]
interface
• ethernet unit/port
- unit - Stack unit. (Range: 1)
- port - Port number. (Range: 1-28)
• port-channel channel-id (Range: 1-8)
Default Setting
Shows all interfaces.
Command Mode
Normal Exec, Privileged Exec
Command Usage
If no interface is specified, information on all interfaces is displayed.
Console#show interfaces counters ethernet 1/7
Ethernet 1/7
Iftable stats:
Octets input: 30658, Octets output: 196550
Unicast input: 6, Unicast output: 5
Discard input: 0, Discard output: 0
Error input: 0, Error output: 0
Unknown protos input: 0, QLen output: 0
Extended iftable stats:
Multi-cast input: 0, Multi-cast output: 3064
Broadcast input: 262, Broadcast output: 1
Ether-like stats:
Alignment errors: 0, FCS errors: 0
Single Collision frames: 0, Multiple collision frames: 0
SQE Test errors: 0, Deferred transmissions: 0
Late collisions: 0, Excessive collisions: 0
Internal mac transmit errors: 0, Internal mac receive errors: 0
Frame too longs: 0, Carrier sense errors: 0
Symbol errors: 0
RMON stats:
Drop events: 0, Octets: 227208, Packets: 3338
Broadcast pkts: 263, Multi-cast pkts: 3064
Undersize pkts: 0, Oversize pkts: 0
Fragments: 0, Jabbers: 0
CRC align errors: 0, Collisions: 0
Packet size <= 64 octets: 3150, Packet size 65 to 127 octets: 139
Packet size 128 to 255 octets: 49, Packet size 256 to 511 octets: 0
Packet size 512 to 1023 octets: 0, Packet size 1024 to 1518 octets: 0
Console#