Installation guide
Table Of Contents
- Chapter 1: Introduction
- Chapter 2: Initial Configuration
- Chapter 3: Configuring the Switch
- Using the Web Interface
- Navigating the Web Browser Interface
- Panel Display
- Main Menu
- Basic Configuration
- Displaying System Information
- Displaying Switch Hardware/Software Versions
- Displaying Bridge Extension Capabilities
- Setting the Switch’s IP Address
- Enabling Jumbo Frames
- Managing Firmware
- Saving or Restoring Configuration Settings
- Console Port Settings
- Telnet Settings
- Configuring Event Logging
- Resetting the System
- Setting the System Clock
- Simple Network Management Protocol
- User Authentication
- Configuring User Accounts
- Configuring Local/Remote Logon Authentication
- Configuring Encryption Keys
- AAA Authorization and Accounting
- Configuring HTTPS
- Replacing the Default Secure-site Certificate
- Configuring the Secure Shell
- Configuring Port Security
- Configuring 802.1X Port Authentication
- Web Authentication
- Network Access - MAC Address Authentication
- MAC Authentication
- Access Control Lists
- Port Configuration
- Address Table Settings
- Spanning Tree Algorithm Configuration
- VLAN Configuration
- Link Layer Discovery Protocol
- Class of Service Configuration
- Quality of Service
- VoIP Traffic Configuration
- Multicast Filtering
- Multicast VLAN Registration
- DHCP Snooping
- IP Source Guard
- IP Clustering
- UPnP
- Chapter 4: Command Line Interface
- Using the Command Line Interface
- Entering Commands
- Command Groups
- Line Commands
- General Commands
- System Management Commands
- Flash/File Commands
- Authentication Commands
- Access Control List Commands
- SNMP Commands
- Interface Commands
- Mirror Port Commands
- Rate Limit Commands
- Link Aggregation Commands
- Address Table Commands
- LLDP Commands
- lldp
- lldp holdtime-multiplier
- lldp medFastStartCount
- lldp notification-interval
- lldp refresh-interval
- lldp reinit-delay
- lldp tx-delay
- lldp admin-status
- lldp notification
- lldp mednotification
- lldp basic-tlv management-ip-address
- lldp basic-tlv port-description
- lldp basic-tlv system-capabilities
- lldp basic-tlv system-description
- lldp basic-tlv system-name
- lldp dot1-tlv proto-ident
- lldp dot1-tlv proto-vid
- lldp dot1-tlv pvid
- lldp dot1-tlv vlan-name
- lldp dot3-tlv link-agg
- lldp dot3-tlv mac-phy
- lldp dot3-tlv max-frame
- lldp dot3-tlv poe
- lldp medtlv extpoe
- lldp medtlv inventory
- lldp medtlv location
- lldp medtlv med-cap
- lldp medtlv network-policy
- show lldp config
- show lldp info local-device
- show lldp info remote-device
- show lldp info statistics
- UPnP Commands
- Spanning Tree Commands
- spanning-tree
- spanning-tree mode
- spanning-tree forward-time
- spanning-tree hello-time
- spanning-tree max-age
- spanning-tree priority
- spanning-tree pathcost method
- spanning-tree transmission-limit
- spanning-tree mst-configuration
- mst vlan
- mst priority
- name
- revision
- max-hops
- spanning-tree spanning-disabled
- spanning-tree cost
- spanning-tree port-priority
- spanning-tree edge-port
- spanning-tree portfast
- spanning-tree link-type
- spanning-tree loopback-detection
- spanning-tree loopback-detection release-mode
- spanning-tree loopback-detection trap
- spanning-tree mst cost
- spanning-tree mst port-priority
- spanning-tree protocol-migration
- show spanning-tree
- show spanning-tree mst configuration
- VLAN Commands
- Priority Commands
- Quality of Service Commands
- Voice VLAN Commands
- Multicast Filtering Commands
- Multicast VLAN Registration Commands
- IP Interface Commands
- IP Source Guard Commands
- DHCP Snooping Commands
- IP Cluster Commands
- Appendix A: Software Specifications
- Appendix B: Troubleshooting
- Glossary
- Index
Command Line Interface
4-262
4
• group-id - Group identifier of this protocol group. (Range: 1-2147483647)
• frame
1
- Frame type used by this protocol. (Options: ethernet, rfc_1042,
llc_other)
• protocol - Protocol type. The only option for the llc_other frame type is
ipx_raw. The options for all other frames types include: ip, arp, and rarp.
Default Setting
No protocol groups are configured.
Command Mode
Global Configuration
Example
The following creates protocol group 2, and specifies Ethernet frames transmitting
ARP protocol type traffic:
protocol-vlan protocol-group (Configuring VLANs)
This command globally maps a protocol group to a VLAN. Use the no form to
remove the protocol mapping.
Syntax
protocol-vlan protocol-group group-id vlan vlan-id
no protocol-vlan protocol-group group-id vlan
• group-id - Group identifier of this protocol group. (Range: 1-2147483647)
• vlan-id - VLAN to which matching protocol traffic is forwarded.
(Range: 1-4092)
Default Setting
No protocol groups are mapped to any VLANs.
Command Mode
Global Configuration
Command Usage
• When creating a protocol-based VLAN, do not assign interfaces to the
protocol VLAN via any of the standard VLAN commands. If you assign
interfaces using any of the other VLAN commands (such as vlan on
page 4-243), the switch will admit traffic of any protocol type into the
associated VLAN.
• When a frame enters the switch that has protocol VLANs configured, it is
processed in the following manner:
- If the frame is tagged, it will be processed according to the standard rules
1.
SNAP frame types are not supported by this switch due to hardware limitations.
Console(config)#protocol-vlan protocol-group 2 add frame-type ethernet
protocol-type arp
Console(config)#