Advanced Display Systems H170 LCD Monitor User Manual www.edge10.com The display comes with a three years on site warranty. To activate your warranty please register your display at www.edge10.
Contents 1. Instructions for Federal Communications Commission Compliance……..2 2. CE Statement………………………………………………………………….4 Safety EMC 3. Introduction…………………………………………………………………...6 General Specifications Monitor Characteristics Accessories Precautions 4. Installation……………………………………………………………………..7 Terminal Connection Pre-installation Check 5. Operation……………………………………………………………………....8 Keypad Operating OSD Menu OSD Icon Overview 6. Specification &Technical Data…………………………………………….....13 7.
1.0 Instructions for Federal Communications Commission (FCC) Compliance This device has passed the tests stipulated by Article 15 of FCC Compliance and conforms to the limitations and provisions for Class-B digital equipment. The restrictions are formulated to prevent the harmful interference with radio frequencies produced by or used by household appliances.
This is to state that this 17” LCD monitor complies with the following compulsory regulations: z Safety This appliance complies with LVD-73/23/EEC Low Voltage Direction (EN60950-1:2001) requirements: • Electrical shock protection • Energy risk protection • Fire hazard protection • Hazardous electromagnetic emissions protection • Protection against hazardous substances produced during normal operation or malfunction • Mechanical and moving parts hazards z EMC This device complies with the 89/336/EE
1. Please carefully read this manual before operating the device and keep it available for future reference. 2. To avoid the danger of the monitor falling and thereby possibly causing injury and/or serious damage to the monitor itself, do not place it on unstable cars or desks. Be careful to avoid placing any stress on the LCD screen during handling. 3.
3.0 Introduction General Specifications This high-quality 17” monitor is based on a liquid crystal display (LCD) with exceptional resolution and features multi-frequency intelligent scanning in the range of 30 to 80 KHz. Caution: In order to maintain this monitor in optimal working condition, please carefully read this manual before use.
4.0 Installation Terminal Connection f e d c NO. Terminal Function c d e f AC-In AC power input 100~240V, 50/60HZ Audio-In (optional) DVI-In (optional) D Sub 15 VGA -In Audio input To PC DVI To PC D Sub 15 VGA Pre-installation Check Please check the label on the nameplate on the back cover first. Input voltage between 100V and 240V should be used with this monitor. Also please make sure this monitor and your main system (computer) is powered off before attaching any connectors.
5.0 Operation Keypad Operating The LCD monitor has been preset at the factory with the Timing shown in Appendix to create optimal picture. Users are also able to adjust the picture to the desired brightness and sharpness by following the instructions.
OSD Menu OSD function allows the user to easily adjust the display to the desired quality. Structure of OSD Operating Procedure 1.Power on the LCD monitor. 2.Press “d” or “f “ to pop up OSD menu. 3.Press “d” to select main menu item. 4.Press “f “ to select sub menu item. 5.Press “+” and “-“ buttons to adjust. 6.Press the EXIT button when finish adjusting.
The Adjustment of Monitor’s Screen Display There are two ways to adjust the monitor’s screen, i.e. auto adjustment and manual adjustment. Auto adjustment 1. Power ON the LCD monitor and computer. 2. Select “AUTO SETUP” of OSD screens by pressing the“d” button to “AUTO SETUP”. 3. Press “+” button while displaying “AUTO SETUP” screen. 4. The auto adjustment is started. “AUTO SETUP” will be displayed during auto adjustment. It takes about 10 seconds to finish adjustment.
6.
NO SIGNAL INPUT 1. 2. 3. 4. If this warning appears, please check the connector. If it is bent or damaged, the signal cable may be affected. If the monitor is in “sleep” mode to save power, please move the mouse or press any key to “wake” it and return to working mode. Please check relevant diagrams, and make sure the monitor has been properly configured. Please check the signal cable. If the type is incorrect, please use the cable that came with the monitor. OUT OF RANGE H : 35KHz V : 86.
7.0 Specification & Technical Data Model No. H170 Input Signal Analog RGB 0.7Vp-p /75 ohm, TTL Sync,Digital RGB TMDS(optional) Scan Frequency H: 30~80 KHz ,V: 55~75 Hz 640x400,720x400,640x480,800x600, 832x624, 1024x768, 1152x864, 1152x870,1280x960, 1280x1024 RGB Mode OSD Brightness, contrast, H./V.
8.0 Energy-saving Modes When this product is operated, it complies with relevant power-saving measures stipulated by the Energy Star and VESA (Video Electronics Standards Association) standards. When the monitor is left unused, it can also automatically eliminate unnecessary power consumption. If the user intends to use this feature, the monitor must be connected to a computer with a power management system that complies with VESA standards.
Display Mode 640 x 480 720 x 350 720 x 400 VESA 800 x 600 1024 x 768 1280 x 960 1280 x 1024 Macintosh PC-9800 SUN 640 x 480 832 x 624 1152 x 864 1152 x 870 640 x 400 1152 x 900 1280*1024 1280 x 960 1280 x 1024 Horizontal Frequency Vertical Frequency 31.4 KHz 59.9 Hz 37.8 KHz 37.5 KHz 31.4 KH/z 31.5 KHz 35.1 KHz 37.9 KHz 46.9 KHz 48.1 KHz 48.4 KHz 56.5 KHz 60.0 KHz 60.0 KHz 63.9 KHz 79.9 KHz 35.0 KHz 49.7 KHz 63.8 KHz 68.6 KHz 24.8 KHz 61.8 KHz 71.6 KHz 62.5 KHz 81.1 KHz 72.8 Hz 75.0 Hz 70.0 Hz 70.
Question: What should I do if there is no picture? Make sure the cable is connected to the port on your PC’s display card. Make sure the computer and screen are both turned on. z Make sure the pins on the connector head of the cable are not bent or broken. z z Question: What should I do if amber LED lights are on but there is no picture? z z Make sure the cable is connected to the port on your PC’s display card. Check if the computer is in sleep mode or not.
www.edge10.
