Industrial Gigabit Ethernet Switch ECIS4500 Series Quick Installation Guide www.edge-core.
Quick Start Guide ECIS4500 6T2F Industrial Gigabit Ethernet Switch Industrial Gigabit Ethernet Switch with 6 10/100/1000BASE-T ports, 2 10/100/1000BASE-X SFP slots ECIS4500 8T2F Industrial Gigabit Ethernet Switch Industrial Gigabit Ethernet Switch with 8 10/100/1000BASE-T ports, 2 10/100/1000BASE-X SFP slots ECIS4500 6T4F Industrial Gigabit Ethernet Switch Industrial Gigabit Ethernet Switch with 6 10/100/1000BASE-T ports, 4 10/100/1000BASE-X SFP slots ECIS4500 4P4T Industrial Gigabit Ethernet Switch Indu
ECIS4500 Quick Installation Guide ECIS4500 Series Industrial switch Quick Installation Guide Overview The managed Ethernet switch solutions are designed for supporting standard industrial applications. The managed switches are easier to prioritize, partition, and organize user’s network, providing a more reliable and better quality services.
ECIS4500 Quick Installation Guide Safety Instructions Overview When a fiber connection is removed during installation, testing, servicing or an active fiber is broken, ocular exposure to optical energy may be potentially hazardous, depending on the laser output power. The primary hazards of exposing laser radiation from an optical-fiber communication systems are: ● Damage to eyes from accidental exposure to a beam emitted by a laser source.
ECIS4500 Quick Installation Guide Appearance ECIS4500-6T4F/8T2F/6T2F ECIS4500-8P2T4F/8P4F/4P2T2F/4P4T 5
ECIS4500 Quick Installation Guide Faceplate ECIS4500-8T2F ECIS4500-8P2T4F ECIS4500-6T4F ECIS4500-6T2F ECIS4500-8P4F ECIS4500-4P2T2F 6 ECIS4500-4P4F
ECIS4500 Quick Installation Guide DIN-rail mounting Mounting steps: 1. Screw the din-clip with screws in the accessory kit. 2. Hook the unit onto the din-rail. 3. Push the bottom of the unit towards the din-rail until it locks in place. Wall mounting Mounting steps: 1. Screw the wall-mount brackets with screws in the accessory kit.
ECIS4500 Quick Installation Guide Ethernet Interface (RJ-45 Ethernet) The switch provides two types of Ethernet interfaces: electrical (RJ-45) and optical (SFP) interfaces. Connecting the Ethernet interface via RJ-45: ● To connect the switch to a PC, use straight-through or cross-over Ethernet cables, ● To connect the switch to an Ethernet device, use UTP (Unshielded Twisted Pair) or STP (Shielded Twisted Pair) Ethernet cables.
ECIS4500 Quick Installation Guide Connecting Power Terminal Block The switch can be powered from two power supplies (input range 12V – 58V). Insert the positive and negative wires into V+ and V- contacts on the terminal block respectively and tighten the wire-clamp screws to prevent the wires from being loosened. Note: 1. The DC power should be connected to a well-fused power supply.
ECIS4500 Quick Installation Guide Alarm Relay and Ground The alarm relay output contacts are in the middle of the DC terminal block connector as shown in the figure below. The alarm relay out is “Normal Open”, and it will be closed when detected any predefined failure such as power failures or Ethernet link failures. The relay output with current carrying capacity of 0.
ECIS4500 Quick Installation Guide To connect the host PC to the console port, a RJ-45 (male) connector-to-RS232 DB9 (female) connector cable is required. The RJ-45 connector of the cable is connected to the CID port of IVS-500; the DB9 connector of the cable is connected to the PC COM port. The pin assignment of the console cable is shown below: Connect and Login to Managed Switch 1. Connecting to the Ethernet port (RJ-45 Ethernet port) of Managed Switch. 2. Factory default IP: 192.168.2.10 255.255.255.
ECIS4500 Quick Installation Guide CLI Initialization and Configuration (Optional) 1. Connecting to the Ethernet port (RJ-45 Ethernet port) of managed switch 2. Key-in the command under Telnet: telnet 192.168.2.10 3. Login with default account and password. 4. Username: admin; Password: admin Change the IP with commands listed below: CLI Command: enable configure terminal interface vlan 1 ip address xxx.xxx.xxx.xxx xxx.xxx.xxx.