Industrial Gigabit Ethernet Switch ECIS4500 Series Version Number: 1.0 CLI Reference Guide www.edge-core.
CLI Reference Guide ECIS4500 6T2F Industrial Gigabit Ethernet Switch Industrial Gigabit Ethernet Switch with 6 10/100/1000BASE-T ports, 2 10/100/1000BASE-X SFP slots ECIS4500 8T2F Industrial Gigabit Ethernet Switch Industrial Gigabit Ethernet Switch with 8 10/100/1000BASE-T ports, 2 10/100/1000BASE-X SFP slots ECIS4500 6T4F Industrial Gigabit Ethernet Switch Industrial Gigabit Ethernet Switch with 6 10/100/1000BASE-T ports, 4 10/100/1000BASE-X SFP slots ECIS4500 4P4T Industrial Gigabit Ethernet Switch In
About This Guide This guide includes detailed information on the switch software, including how to operate and use the management functions of the switch. To deploy this switch effectively and ensure trouble-free operation, you should first read the relevant sections in this guide so that you are familiar with all of its software features. Who Should Read This This guide is for network administrators who are responsible for operating and Guide? maintaining network equipment.
Contents 1 SCOPE ................................................................................................................................................................... 3 1.1 1.2 1.3 1.4 1.5 2 OPERATOR INTERFACE .................................................................................................................................. 7 2.1 2.2 2.3 2.4 2.5 2.6 2.7 3 SCOPE .................................................................................................................
Contents 3.2.31 3.2.32 3.2.33 3.2.34 3.2.35 3.2.36 3.2.37 3.2.38 3.2.39 3.2.40 3.2.41 3.2.42 3.2.43 3.2.44 3.2.45 3.2.46 3.2.47 3.2.48 3.2.49 3.2.50 3.2.51 3.2.52 3.2.53 3.2.54 3.2.55 3.2.56 3.2.57 3.2.58 3.2.59 3.2.60 3.2.61 3.2.62 3.2.63 3.2.64 3.2.65 3.2.66 3.2.67 3.2.68 3.2.69 3.2.70 3.2.71 3.2.72 3.2.73 3.2.74 3.2.75 3.2.76 3.2.77 3.2.78 3.2.79 3.2.80 3.2.81 3.2.82 3.2.83 3.2.84 3.2.85 3.2.86 3.2.87 3.2.88 3.2.89 ii show mac address table aging-time....................................................
Contents 3.2.90 show radius-server [ statistics ] ................................................................................................................ 29 3.2.91 show rfc2544 profile [ ] .......................................................................................................... 30 3.2.92 show voice ................................................................................................................................................. 30 3.2.93 show web ...........
Contents 3.3.55 logout ........................................................................................................................................................ 40 3.3.56 mac address-table aging-time ................................................................................................................... 40 3.3.57 mac address-table static ............................................................................................................................ 40 3.3.58 more......
Contents 3.5.9 ip dhcp relay information option ............................................................................................................... 52 3.5.10 ip dhcp retry interface vlan ....................................................................................................................... 52 3.5.11 ip dhcp snooping ....................................................................................................................................... 52 3.5.12 ip helper-address .
Contents 3.9.16 SNMP trap receive ipv4 host ..................................................................................................................... 62 3.10 QOS FUNCTION COMMAND..................................................................................................................................... 62 3.10.1 qos qce....................................................................................................................................................... 62 3.10.
Contents 3.13.12 ipv6 mld unknown-flooding ....................................................................................................................... 71 3.13.13 ipv6 route................................................................................................................................................... 72 3.14 AUTHENTICATE MODE COMMANDS .......................................................................................................................... 72 3.14.
Contents 3.19.1 voice vlan .................................................................................................................................................. 81 3.19.2 voice vlan aging-time ................................................................................................................................ 81 3.19.3 voice vlan class ......................................................................................................................................... 81 3.19.
Contents ix
1. Scope 1.1 Scope 1.2 Audience 1.3 Pre-required Knowledge 1.4 Access to Hardware Interface 1.
2
Scope 1 Scope 1.1 Scope This user guide describes the commands and parameters of the Command Line Interface (CLI) as implemented in the current version of ECIS4500 series software. These commands are used to set-up, administer and maintain the system. 1.2 Audience The guide is intended for Operating personnel (sometimes called craft persons). 1.3 Pre-required Knowledge The reader must be familiar with the: Basic operations of ECIS4500 series (see the HW Installation Guide).
Scope 4
2. Operator Interface 2.1 Introduction 2.2 Connect Interface 2.3 Authorization Level 2.4 Screen Description 2.5 Execution Modes 2.6 Getting Help 2.7 Terminal Key Function 2.
6
Operator Interface 2 Operator Interface 2.1 Introduction Access to the Switch is protected by a logon security system. You can log on to the switch with the user name and password. After three failed logon attempts, the system refuses further attempts. After you log on, the system monitors the interface for periods of inactivity. If the interface is inactive for too long, you are automatically logged off. The CLI initial user name is (admin) and none password ().
192.168.2.10 Figure 2-1 2.4 Screen Description Execution Modes The CLI contains several execution modes. Users will see different set of commands under different execution modes. Table 2-1 lists all the execution modes and their purposes. When users enter a certain execution mode, the corresponding mode prompt will be displayed automatically on the screen. The mode prompts of all the execution modes are also listed in Table 2-1.
Operator Interface 2.6 Terminal Key Function Following is the list of all the terminal keys and their function. Table 2-2 List of Terminal Keys ENTER CTRL-M TAB CTRL-I Tab completion. If tab is pressed after a non-whitespace character, complete the word before the Tab. If tab is pressed after a whitespace character, complete the next word. Display available commands If ? is pressed after a non-whitespace character, show possible choices for this word.
10
3. Commands Descriptions 3.1 Initialize Mode Commands 3.2 Enable Mode Commands 3.3 Configure Mode Commands 3.4 VLAN Mode Commands 3.5 Interface VLAN Mode Commands 3.6 Ring Group Mode Commands 3.7 Spanning Tree Configure Commands 3.8 sFlow Configure Command 3.9 SNMP Configure Command 3.10 Qos Function Command 3.11 IGMP Functional Commands 3.12 MVR Functional Commands 3.13 MLD Functional Commands 3.14 Authenticate Mode Commands 3.15 Loop-Protection Configure commands 3.
3 Commands Descriptions 3.1 Initialize Mode Commands The commands in this section (except ‘enable’ command) can be executed under all command modes. These commands are global commands. 3.1.1 exit Description Syntax Parameter Exit current mode and quit CLI. exit None 3.1.2 configure terminal Description Syntax Parameter Enter configuration mode. configure terminal None 3.1.3 enable Description Syntax Parameter 3.1.4 Enter enable mode.
3.2 Enable Mode Commands All the “show - -” commands in this section can also be executed under any other command mode except Initialize Mode. 3.2.1 configure terminal Description Syntax Parameter Enter configuration mode. configure None 3.2.2 disable Description Syntax Parameter Enter init mode. disable None 3.2.3 show aaa Description Syntax Parameter Show AAA show aaa None 3.2.
dhcp conflicts arp-inspection The ACEs that are configured by DHCP module The ACEs that did not get applied to the hardware due to hardware limitations The ACEs that are configured by ARP Inspection module 3.2.6 show aggregation Description Syntax Parameter Aggregation show aggregation [ mode ] Name mode Description Traffic distribution mode 3.2.
3.2.10 show ip Description Syntax Parameter IP information show ip Name arp dhcp http igmp interface name-server route source ssh statistics verify Description Address Resolution Protocol Dynamic Host Configuration Protocol Hypertext Transfer Protocol Internet Group Management Protocol IP interface status and configuration Domain Name System Display the current ip routing table source command Secure Shell Traffic statistics verify command 3.2.
3.2.14 show line Description Syntax Parameter Alive line information show line [ alive ] Name alive Description Display information about alive lines 3.2.15 show logging Description Syntax Logging information show logging [ switch ] show logging [ info ] [ warning ] [ error ] [ switch ] Parameter Name log_id error info warning Description Logging ID Error Infomation Warning 3.2.
3.2.21 show running-config interface vlan Description Syntax Parameter Show default running configuration. show running-config interface vlan [ all-defaults] None 3.2.22 show running-config all-defautls Description Syntax Parameter Show all default setting show running-config [ all-defaults ] None 3.2.
3.2.27 show clock Description Syntax Parameter Show current time. Show clock None 3.2.28 show ddmi Description Syntax Parameter Show DDMI configuration show ddmi None 3.2.29 show version Description Syntax Parameter Show version information. show version None 3.2.30 show system inventory Description Syntax Parameter Show system inventory. show system inventory None 3.2.31 show mac address table aging-time Description Syntax Parameter Show aging time for MAC learning table (system-wide).
3.2.35 show mac address table learning Description Syntax Learn/disable/secure stat show mac address-table [ conf | static | aging-time | { { learning | count } [ interface ( [ ] ) ] } | { address [ vlan ] } | vlan | interface ( [ ] ) ] Parameter Name Description 3.2.
3.2.40 show fdb static table Description Syntax Parameter Show static MAC forwarding table. show mac address-table static None 3.2.41 show fdbstatic interface gigabit Description Syntax Show static MAC forwarding table per gigabit port. Show mac address-table { learning | count } [ interface [ ] ] Parameter Name Description Port type in Fast, Giga or Tengiga ethernet Valid values: 1 ~ 10 Type: Mandatory 3.2.
3.2.
3.2.49 show sflow Description Syntax Sflow information show sflow show sflow statistics { receiver [ ] | samplers [ interface [ ] ( [ ] ) ] } Parameter Name receiver samplers interface port_type v_port_type_list Description Show statistics for receiver Show statistics for samplers Interface GigabitEthernet, 1 Gigabit Ethernet Port Port list in 1/1-14 3.2.
view view_name oid_subtree MIB view configuration MIB view name MIB view OID 3.2.51 show spanning-tree Description Syntax System Wide Spanning Tree Setting/Status.
3.2.57 show vlan brief Description Syntax Parameter VLAN summary information show vlan [ id | name | brief ] Name id vlan_list name name brief Description VLAN status by VLAN id VLAN IDs 1-4095 VLAN status by VLAN name A VLAN name VLAN summary information 3.2.
3.2.
3.2.67 show pvlan [ ] Description Syntax Parameter PVLAN ID show pvlan [ ] Name pvlan_list Description PVLAN ID to show configuration for 3.2.68 show pvlan isolation [ interface [ ] ] Description Syntax Parameter Show all port isolation information. show pvlan isolation [ interface [ ] ] None Name Description Port type in Fast, Giga or Tengiga ethernet Valid values: 1 ~ 10 Type: Mandatory 3.2.
3.2.73 show qos maps Description Syntax MAPS show qos maps { maps [ dscp-cos ] [ dscp-ingress-translation ] [ dscp-classify ] [ cos-dscp ] [ dscp-egress-translation ] } Parameter Name cos-dscp dscp-classify dscp-cos dscp-egress-translation dscp-ingress-translation Description Map for cos to dscp Map for dscp classify enable Map for dscp to cos Map for dscp egress translation Map for dscp ingress translation 3.2.
3.2.78 show rmon Description Syntax show rmon alarm [ ] show rmon event [ ] show rmon history [ ] show rmon statistics [ ] Parameter Name alarm event history statistics id_list Description Display the RMON alarm table Display the RMON event table Display the RMON history table Display the RMON statistics table <1~65535>, Statistics entry list 3.2.
3.2.84 show interface gigabit vlan Description Syntax Parameter Show vlan information per port show interface gigabit vlan Name Description Gigabit port. Valid values: 1 ~ 10 Type: Mandatory 3.2.85 show vlan-trans Description Syntax Parameter Show VLAN translation table for all show vlan-trans None 3.2.86 show multicast-fdb Description Syntax Parameter Show IGMP group membership table show multicast-fdb None 3.2.
3.2.91 show rfc2544 profile [ ] Description show rfc2544 profile name Syntax show rfc2544 profile [ ] Parameter Name Description rfc2544 profile name 3.2.
3.3 Configure Mode Commands Commands that can be executed under Configure Mode 3.3.1 interface gigabit Description Syntax Parameter Gigabit Ethernet interface. (enter gigabit interface mode) interface gigabit Name Description Valid values: 1 ~ 10 Type: Mandatory 3.3.2 interface vlan Description Syntax Parameter Vlan Ethernet interface (enter mode of interface vlan) interface vlan Name Description Valid values: 1 ~ 4094 Type: Mandatory 3.3.
3.3.7 alarm history clear Description Syntax Parameter Clear alarm history alarm history clear Name Description 3.3.8 banner Description Syntax Parameter Banner control banner { LINE | exec | login | motd } Name LINE exec login motd Description c banner-text c, where 'c' is a delimiting character Set EXEC process creation banner Set login banner Set Message of the Day banner 3.3.9 ddmi Description Syntax Parameter Enable DDMI function ddmi None 3.3.
3.3.13 clock timezone Description Syntax Parameter Set time zone. clock timezone <-23-23> [ <0-59> ] Name < word16> default Description Valid values: please see 'list timezone' Type: Mandatory Set time zone to default (GMT/UTC). Type: Mandatory 3.3.14 clock summer-time set [start-time] [end-time] Description Syntax Set date/time.
3.3.17 syslog {enable|disable} Description Syntax Parameter Disable or enable syslog service. logging on no logging on None 3.3.
3.3.24 dir Description Syntax Parameter Directory of all files in flash: file system dir 3.3.25 do Description Syntax Parameter To run exec commands in config mode do Name Description Exec Command 3.3.26 duplex Description Syntax Parameter Set duplex mode duplex { half | full | auto [ half | full ] } Name half full auto [ half | full ] Description Forced half duplex. Forced full duplex. Auto negotiation of duplex mode. Advertise half /full duplex. 3.3.
3.3.
3.3.36 ip arp inspection translate Description Syntax IP ARP inspection entry interface configuration ip arp inspection translate [ interface ] Parameter Name port_type port_type_id vlan_id mac_ucast ipv4_ucast Description Port type in Fast, Giga or Tengigaethernet Port ID in the format of switch-no/port-no Select a VLAN id to configure Select a MAC address to configure Select an IP Address to configure 3.3.
3.3.42 ip source binding interface Description Syntax IP source binding entry interface configuration Ip source binding interface Parameter Name port_type port_type_id vlan_id ipv4_ucast mac_ucast Description Port type in Fast, Giga or Tengigaethernet Port ID in the format of switch-no/port-no Select a VLAN id to configure Select an IP Address to configure Select a MAC address to configure 3.3.
3.3.49 ipmc range Description Syntax A range of IPv4/IPv6 multicast addresses for the profile ipmc range { [ ] | [ ] } Parameter Name word16 ipv4_mcast ipv4_mcast ipv6_mcast ipv6_mcast Description Range entry name in 16 char's Valid IPv4 multicast address Valid IPv4 multicast address that is not less than start address Valid IPv6 multicast address Valid IPv6 multicast address that is not less than start address 3.3.
3.3.55 logout Description Syntax Parameter System logout logout 3.3.56 mac address-table aging-time Description Syntax Parameter MAC table entries/configuration mac address-table aging-time Name Description Aging time in seconds, 0 disables aging 3.3.
3.3.61 port-security Description Syntax Parameter Port security port-security [aging] [time ] Name aging time v_10_to_10000000 Description Enable/disable port security aging Time in seconds between check for activity on learned MAC addresses <10-10000000> seconds 3.3.
3.3.
3.3.66 rmon alarm Description Syntax RMON Event rmon event [ log ] [ trap ] { [ description ] } Parameter Name description log trap Description Specify a description of the event Generate RMON log when the event fires Generate SNMP trap when the event fires 3.3.
3.3.71 mac address-table aging-time
3.3.77 speed Description Syntax Parameter Configures interface speed. If you use 10, 100, or 1000 keywords with the auto keyword the port will only advertise the specified speeds. speed { 10g | 2500 | 1000 | 100 | 10 | auto { [ 10 ] [ 100 ] [ 1000 ] } } Name 1000 100 10 auto [ 10 ] [ 10 0] [ 1000 ] Description 1Gbps 100Mbps 10Mbps Auto negotiation 10Mbps 100Mbps 1Gbps 3.3.
3.3.82 upnp Description Syntax Parameter Set UPnP's configurations upnp 3.3.83 upnp advertising-duration Description Syntax Parameter Set UPnP's advertising duration upnp advertising-duration <100-86400> Name 100-86400 Description advertising duration 3.3.84 upnp ttl Description Syntax Parameter Set UPnP's TTL value upnp ttl <1-255> Name 1-255 Description TTL value 3.3.
crw sro srw cro crw sro srw Configuration Read-write level Status/Statistics Read-only level Status/Statistics Read-write level 3.3.87 flow-control {enable|disble} Description Syntax Parameter Enable/Disable flow-control. flow-control {enable|disble} Name enable disable Description Enable flow-control. Disable flow-control. 3.3.88 speed Description Syntax Configure gigabit Ethernet speed and Copper/SFP for gigabit port 7~8.
3.4 VLAN Mode Commands 3.4.1 vlan Description Syntax Parameter VLAN commands vlan Name vlan_lis Description ISL VLAN IDs 1~4095 3.4.2 vlan ethertype s-custom-port Description Syntax Parameter Vlan Ether type for custom S-ports configuration vlan ethertype s-custom-port <0x0600-0xffff> Name 0x0600-0xffff Description Ethertype (Range: 0x0600-0xffff) 3.4.
3.4.6 switchport forbidden vlan Description Syntax Parameter Adds or removes forbidden VLANs from the current list of forbidden VLANs switchport forbidden vlan { add | remove } Name add remove vlan_list Description Add to existing list. Remove from existing list. VLAN IDs 3.4.
3.4.11 switchport mode Description Syntax Parameter Set switching mode switchport mode { access | trunk | hybrid } Name access trunk hybrid Description Set mode to ACCESS unconditionally Set mode to TRUNK unconditionally Set mode to HYBRID unconditionall 3.4.
3.5 Interface VLAN Mode Commands 3.5.1 interface Description Syntax Parameter Interface configuration interface [ ] Name port_type port_type_list Description Port type in Fast, Giga or Tengigaethernet List of Port ID, ex, 1/1,3-5;2/2-4,6 3.5.2 interface vlan Description Syntax Parameter VLAN interface configurations interface vlan Name vlan_list Description List of VLAN interface numbers, 1~4095 3.5.
3.5.7 ip dhcp server Description Syntax Parameter DHCP Server ip dhcp server 3.5.8 ip dhcp relay Description Syntax Parameter DHCP relay agent configuration ipdhcp relay 3.5.9 ip dhcp relay information option Description Syntax Parameter IP DHCP relay information option(Option 82) ipdhcp relay information option 3.5.10 ip dhcp retry interface vlan Description Syntax Parameter Restart the DHCP query process ipdhcp retry interface vlan Name vlan_id Description Vlan ID 3.5.
3.6 RingV2 Group Mode Commands 3.6.1 ringv2 protect Description Syntax Parameter To configure ring protection. ring protect Name group1 group2 group3 Description Configure ring protection v2 group1 (Ring) Configure ring protection v2 group2 (Ring) Configure ring protection v2 group3 (Chain) 3.6.2 guard-time Description Syntax Parameter Set guard time guard-time { } Name Description ringGuardTimerDef <10-3600>, unit: secound. Default is 10 secounds 3.6.
dual-homing chain-head chain-member chain-tail b-chain-central-block b-chain-member b-chain-terminal-1 b-chain-terminal-2 3.7 Set role to dual homing Set role to chain head Set role to chain member Set role to chain tail Set role to balancing chain central block Set role to balancing chain member Set role to balancing chain terminal 1 Set role to balancing chain terminal 2 Spanning Tree 3.7.
3.7.7 spanning-tree edge bpdu-filter Description Syntax Parameter Enable BPDU filter (stop BPDU tx/rx) spanning-tree edge bpdu-filter Name Description 3.7.8 spanning-tree mode Description mode STP protocol mode stp 802.1D Spanning Tree rstp Rabid Spanning Tree (802.1w) mstp Syntax Parameter Multiple Spanning Tree (802.1s) spanning-tree mode { stp | rstp | mstp } Name stp rstp mstp Description 802.1D Spanning Tree Rabid Spanning Tree (802.1w) Multiple Spanning Tree (802.1s) 3.7.
3.7.11 spanning-tree mst priority Description Syntax Parameter Priority of the instance Range in seconds spanning-tree mst <0-7> priority <0-61440> Name <0-7> <0-61440> Description instance 0-7 (CIST=0, MST2=1...) Priority of the instance 3.7.12 spanning-tree mst vlan Description Syntax Parameter VLAN keyword spanning-tree mst <0-7> vlan Name <0-7> Description instance 0-7 (CIST=0, MST2=1...) Range of VLANs 3.7.
3.7.16 spanning-tree mst name Description Name of the bridge Revision Syntax Parameter Revision keyword spanning-tree mst name revision <0-65535> Name <0-65535> Description Name of the bridge Revision keyword 3.7.17 spanning-tree mst Description Syntax instance 0-7 (CIST=0, MST2=1...
3.8.2 sflow agent-ip Description Syntax Parameter The agent IP address used as agent-address in UDP datagrams. Defaults to IPv4 loopback address. sflow agent-ip { ipv4 | ipv6 } Name < ipv4_addr > < ipv6_addr> Description Ipv4 address ipv6 address 3.8.3 sflow collector-address Description Syntax Sflow runtime, see sflow_icli_functions sflow collector-address [ receiver ] [ ] Parameter Name < range_list > Description Sampler instance 3.8.
3.8.8 sflow timeout Description Syntax Parameter Receiver timeout measured in seconds. The switch decrements the timeout once per second, and as long as it is non-zero, the receiver receives samples. Once the timeout reaches 0, the receiver and all its configuration is reset to defaults. sflow timeout [ receiver ] <0-2147483647> Name < range_list > <0-2147483647> 3.9 Description Sampler instance Number of seconds. SNMP Configure Command 3.9.
3.9.4 snmp-server community v3 Description Syntax Parameter S Set the SNMP v3 community snmp-server community v3 [ ] Name < word127 > < ipv4_addr > Description Community word IPv4 address IPv4 netmask 3.9.5 snmp-server host Description Syntax Parameter Set SNMP server's configurations snmp-server host Name < word32 > Description Name of the host configuration 3.9.
3.9.9 snmp-server version Description Syntax Parameter Set the SNMP server's version snmp-server version { v1 | v2c | v3 } Name { v1 | v2c | v3 } Description SNMP v1,v2c,v3 3.9.10 snmp-server view Description Syntax Parameter Snmp MIB view configuration snmp-server view { include | exclude } Name < word32 > < word255> { include | exclude } Description MIB view name MIB view OID Included/Excluded type from the view 3.9.
3.9.15 snmp-server security-to-group Description Syntax SNMP server security snmp-server security-to-group model { v1 | v2c | v3 } name group Parameter Name model v1 v2c v3 name security_name group group_name Description security model v1 security model v2c security model v3 security model security user security user name security group security group name 3.9.
3.10.3 qos cos Description Syntax Parameter Class of service configuration qos cos <0-7> Name <0-7> Description Specific class of service 3.10.4 qos dscp-classify Description Syntax Parameter Set qos dscp-classify. qos dscp-classify { zero | selected | any } Name Description 3.10.5 qos dscp-remark Description Syntax Parameter Set qos dscp-remark qos dscp-remark { rewrite | remap | remap-dp } Name Description 3.10.
3.10.
3.10.
Syntax Parameter qos queue-policer queue <0~7> Name <0~7> Description Queue number Traffic meter 3.10.15 qos shaper Description Syntax Parameter Configure qos shaper command qos shaper Name <1-100> Description every level proportion Traffic meter 3.11 IGMP Functional Commands 3.11.
3.11.7 ip igmp snooping querier Description Syntax Parameter IP IGMP querier configuration ip igmp snooping querier { election | address } Name election address ipv4_ucast Description Act as an IGMP Querier to join Querier-Election IGMP Querier address configuration A valid IPv4 unicast address 3.11.8 ip igmp snooping query-interval Description Syntax Parameter IP IGMP snooping Query-Intervalin seconds ip igmp snooping query-interval <1-31744> Name 1-317 Description 1 - 31744 seconds 3.
3.12.2 mvr immediate-leave Description Syntax Parameter mvr immediate leave configuration mvr immediate-leave Name Description 3.12.3 mvr name channel Description Syntax Parameter Multicast VLAN name and channel configuration mvr name channel Name name channel Description MVR multicast VLAN name Profile name in 16 char's 3.12.
3.12.8 mvr name mode Description Syntax Parameter Dynamic MVR operation mode mvr name mode { dynamic | compatible } Name dynamic compatible Description Dynamic MVR operation mode Compatible MVR operation mode 3.12.9 mvr name type Description Syntax Parameter MVR port role configuration mvr name type { source | receiver } Name source receiver Description MVR source port MVR receiver port 3.12.
3.12.14 mvr vlan igmp-address Description Syntax Parameter Set tagged IGMP/MLD frames will be sent mvr vlan igmp-address Name < vlan_list > Description MVR multicast VLAN list A valid IPv4 unicast address for IGMP 3.12.
3.13.5 ipv6 mld snooping last-member-query-interval Description Syntax Parameter ipv6 mld snooping last member query interval in tenths of seconds ipv6 mld snooping last-member-query-interval <0-31744> Name 0-31744 Description 0 - 31744 tenths of seconds 3.13.6 ipv6 mld snooping max-groups Description Syntax Parameter IPv6 MLD group throttling configuration ipv6 mld snooping max-groups <1-10> Name 1-10 Description Maximun number of MLD group registration 3.13.
3.13.13 ipv6 route Description Syntax IPv6 Route ipv6 route { | interface vlan } Parameter Name v_ipv6_subnet v_ipv6_ucast v_vlan_id v_ipv6_addr Description IPv6 prefix x:x::y/z IP address of the DHCP relay server VLAN ID IP address 3.14 Authenticate Mode Commands 3.14.1 radius-server attribute 32 Description Syntax Parameter Configure radius-server attribute radius-server attribute 32 Name id Description Id : line1-253 3.14.
3.14.
3.14.11 tacacs-server deadtime <1-1440> Description Syntax Parameter Time to stop using a TACACS+ server that doesn't respond tacacs-server deadtime <1-1440> Name < <1-1440> Description Time in minutes 3.14.12 tacacs-server deadtime <1-1440> Description Syntax Parameter Time to stop using a TACACS+ server that doesn't respond tacacs-server deadtime <1-1440> Name < <1-1440> Description Time in minutes 3.14.
3.14.18 dot1x timeout Description Syntax Timeout control dot1x timeout { quiet-period } | { tx-period
3.14.23 show radius-server [ statistics ] Description show radius-server statistics Syntax show radius-server [ statistics ] Parameter Name [ statistics ] Description Count radius packet statistics 3.14.24 enable Description Syntax Privilege level control Enable { password [ level ] } | { secret { 0 | 5 } [ level ] } Parameter Name password secret Description Assign the privileged level clear password Assign the privileged level secret 3.14.
3.15.3 loop-protect shutdown-time Description Syntax Parameter Loop protection shutdown time interval loop-protect shutdown-time <0-604800> Name 0-604800 Description Shutdown time in second 3.15.4 loop-protect transmit-time Description Syntax Parameter Loop protection transmit time interval loop-protect transmit-time <1-10> Name 1-10 Description Transmit time in second 3.15.5 loop-protect tx-mode Description Syntax Parameter Loop protection actively generate PDUs loop-protect tx-mode 3.
elin-addr latitude longitude media-vlan-policy Emergency Location Identification Number, (e.g. E911 and others), such as defined by TIA or NENA. Latitude parameter Longitude parameter Use the media-vlan-policy to create a policy, which can be assigned to an interface : Policy id for the policy which is created 3.16.3 lldp receive Description Syntax Enable/Disable decoding of received LLDP frames. lldp receive 3.16.
3.16.7 lldp transmission-delay Description Syntax Parameter Sets LLDP transmision-delay. LLDP transmission delay (the amount of time that the transmission of LLDP frames will delayed after LLDP configuration has changed) in seconds.) lldp transmission-delay <1-8192> Name <1-8192> Description transmission-delay seconds 3.16.8 lldp transmit Description Syntax Parameter Enable/Disabled transmision of LLDP frames. lldp transmit 3.17 RFC2544 Testing Configure Commands 3.17.
3.17.5 rfc2544 stop Description Syntax Parameter Stop execution of an ongoing test rfc2544 stop Name Description Report name to stop execution of 3.17.6 show rfc2544 profile [ ] Description show rfc2544 profile name Syntax show rfc2544 profile [ ] Parameter Name Description rfc2544 profile name 3.18 GVRP Configure Commands 3.18.1 gvrp Description Syntax Parameter Enable GVRP on port(s) gvrp 3.18.
3.19 Voice VLAN Configure Commands 3.19.1 voice vlan Description Syntax Parameter Vlan for Voice appliance attributes voice vlan 3.19.2 voice vlan aging-time Description Syntax Parameter Set secure learning aging time for voice traffic voice vlan aging-time <10-10000000> Name 10-10000000 Description Aging time, 10-10000000 seconds 3.19.
3.20.2 alarm Description Syntax Parameter Set alarm content alarm { mask | unmask | major | minor } 101~114: GE-1~14 Port link down (for 14 port model) Name Description alarmId 151: set Power alarm mask unmask major minor Set alarm as mask, it means event will not be send notify Set alarm as un-mask, it means event will be send notify Set alarm level as major Set alarm level as minor 3.21 PoE Commands 3.21.
3.21.4 poe mode Description Syntax Parameter Set PoE mode. poe mode Name disable enable schedule Description Set poe to disable Set poe to enable always Set poe to enable by scheduling 3.21.5 poe operation Description Syntax Parameter Set PoE operation mode. poe operation Name af at Description Set operation mode to 802.3af(Maximum power 15.4W) Set operation mode to 802.3at(Maximum power 30.0 W) 3.21.
3.21.9 poe schedule Description Syntax Parameter Set PoE power scheduling during the week. poe schedule Name fri mon sat tue wed 84 Description sun thu Day There are 48 time interval one day. Each interval has 30 minutes. ( [1]<00:00-00:29> [2]<00:30-00:59>[3]<01:00-01:29> ... [47]<23:00-23:29> [48]<23:30-23:59>).
