ECS4120 series V1.2.2.30 firmware release note

ManualsBrandsEdgecore Networks ManualsFixed Broadband AccessENHANCED TEMPERATURE L2+ GIGABIT ETHERNET ACCESS / AGGREGATION SWITCH WITH 4 X 10G UPLINKS

ENGINEERING RELEASE NOTES

1/2010 Subject to Change Without Notice Page: 8 of 25

ES4528BH2-HPoE-0815-EC-00176

StaticRoute: Static route doesn't support MIB..

Runtime V1.2.2.12; Loader V0.0.3.0

ES4528BH2-HPoE-0815-EC-00824

Load runtime to ECS4120-28F, the port status always shows link down.

ES4528BH2-HPoE-0815-EC-00823

shutdown port via port security then DRIVER_GROUP_TX counter increase

and cause watchdog reboot

Runtime V1.2.2.10; Loader V0.0.3.0

ES4528BH2-HPoE-0815-EC-00812

prevent ECS4120-28Fv2-I(BID=12) downgrade firmware to v1.2.2.8 and

below.

ES4528BH2-HPoE-0815-EC-00811

system description is incorrect on new hardware

ECS4120-28Fv2-I(BID=12)

ES4528BH2-HPoE-0815-EC-00810

NTP: support to add or delete NTP IPv4/IPv6/hostname servers in SNMP

private MIB

ES4528BH2-HPoE-0815-EC-00797

ZTPv6: After restart this ZTPv6 for 10 times, DUT failed to get IPV6

address.

ES4528BH2-HPoE-0815-EC-00795

DHCPv6: After restart DHCPv6 client on DUT continuously, system halted

and show exception.

ES4528BH2-HPoE-0815-EC-00753

ZTPv6: After DUT fail to get bootfile, CLI show exception.

Runtime V1.2.2.9; Loader V0.0.3.0

ES4528BH2-HPoE-0815-EC-00807

The ERPS convergence time more than 600ms, shall be less than 50ms

ES4528BH2-HPoE-0815-EC-00801

new hw with board id 12 that 2 of 10G ports can not link-up and LED can not

di[play

Runtime V1.2.2.8; Loader V0.0.3.0

ES4528BH2-HPoE-0815-EC-00733

[Enhancement] Support sticky mac behavior refinement.

Runtime V1.2.2.7; Loader V0.0.3.0

ES4528BH2-HPoE-0815-EC-00800

[Enhance] DHCP server

ES4528BH2-HPoE-0815-EC-00799

switch still download config from TFTP server automatically even ip dhcp

dynamic-provision is disabled.

ES4528BH2-HPoE-0815-EC-00798

Master unit rebooted with an error message and changed its state to Slave

after boot up which impacts Automation test

ES4528BH2-HPoE-0815-EC-00794

After firmware upgrade and reboot, debug message print out continually.

ES4528BH2-HPoE-0815-EC-00792

[Enhancement] sflow enabled/disabled syslog

ES4528BH2-HPoE-0815-EC-00791

[enhance] error coding for QinQ default service MIB

ES4528BH2-HPoE-0815-EC-00783

remove OSPF related OID from MIB file, since 4120 does not support OSPF

ES4528BH2-HPoE-0815-EC-00780

[LLDP] Define default value for LLDP IPv6 address

ES4528BH2-HPoE-0815-EC-00769

We can't get the maximum management ip if we let the vlan interface get

ipv6 interface by autoconfig.