ECS4510_Quick Start Guide

ManualsBrandsEdgecore Networks ManualsEnterpriseL2+ Gigabit Ethernet Stackable Switch

– 1 –

Quick Start Guide

28/52-Port L3 Stackable Gigabit Ethernet Switch

ECS4620-28T / ECS4620-28P / ECS4620-28F

ECS4620-52T / ECS4620-52P

The ECS4620-28T, ECS4620-28P, ECS4620-52T, and ECS4620-52P are stackable

Layer 3 switches that provide 24/48 10/100/1000BASE-T RJ-45 ports, and two 10

Gigabit (10G) Small Form Factor Pluggable Plus (SFP+) slots that support 1G and

10G transceivers. The ECS4620-28F is a Layer 3 switch that provides 22 SFP 1G

transceiver slots, two combination Gigabit RJ-45/SFP ports, and two 10G SFP+ slots.

The ECS4620-28P and ECS4620-52P also provide Power-over-Ethernet Plus (PoE+)

capability on the RJ-45 ports.

All switches also provide one rear-panel slot for a dual-port 10G hot-swappable

expansion module.

Note:

For detailed switch installation information, refer to the Installation Guide,

which is on the Documentation CD included with the switch.

Note:

For Safety and Regulatory information, refer to the Safety and Regulatory

Information document included with the switch.

ECS4620-28P

ECS4620-28F

ECS4620-52T

ECS4620-52P

ECS4620-28T

E072014-CS-R03

150200000789A

www.edge-core.com

Summary of content (6 pages)

PAGE 1
Quick Star t Guide 28/52-Port L3 Stackable Gigabit Ethernet Switch ECS4620-28T / ECS4620-28P / ECS4620-28F ECS4620-52T / ECS4620-52P The ECS4620-28T, ECS4620-28P, ECS4620-52T, and ECS4620-52P are stackable Layer 3 switches that provide 24/48 10/100/1000BASE-T RJ-45 ports, and two 10 Gigabit (10G) Small Form Factor Pluggable Plus (SFP+) slots that support 1G and 10G transceivers.
PAGE 2
Quick Start Guide 1. Unpack the Switch Unpack the switch and check the package contents.
PAGE 3
Quick Start Guide 1 1 Connect a grounding wire and lug to the dual-hole grounding point on the switch rear panel, then to rack ground. 4. Connect Power Connect the switch to an AC power source that can provide the following: ◆ ◆ ◆ ◆ ◆ ECS4620-28T: 100 to 240 V, 50-60 Hz, 1.
PAGE 4
Quick Start Guide 5. Verify Switch Verify basic switch operation by checking the system LEDs. Operation When operating normally, the Diag and Power LEDs should both be on green. 1 1 System Status LEDs. 6. Make Initial At this point you may need to make a few basic switch configuration changes Configuration before connecting to the network. It is suggested to connect to the switch console Changes port to perform this task.
PAGE 5
Quick Start Guide 7. Connect Network Install SFP/SFP+ transceivers and connect network cables to port interfaces: Cables ◆ For RJ-45 ports, use 100-ohm Category 5, 5e or better twisted-pair cable for 1000BASE-T connections, Category 5 or better for 100BASE-TX connections, and Category 3 or better for 10BASE-T connections. ◆ First install SFP/SFP+ transceivers and then connect fiber optic cabling to the transceiver ports.
PAGE 6
Quick Start Guide Hardware Specifications Item Specification Chassis Specifications SIze (W x D x H) ECS4620-28T/P/F: 44.0 x 31.5 x 4.4 cm (17.3 x 12.4 x 1.7 in.) ECS4620-52T/P: 44.0 x 39.1 x 4.4 cm (17.3 x 15.4 x 1.7 in.) Weight ECS4620-28T: 3.7 kg (8.16 lb) ECS4620-28P: 4.5 kg (9.92 lb) ECS4620-28F: 3.8 kg (8.38 lb) ECS4620-52T: 4.8 kg (10.58 lb) ECS4620-52P: 6.58 kg (14.