User's Manual
Table Of Contents
- Warranty and Product Registration
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Command Line Interface
- Using the Command Line Interface
- General Commands
- System Management Commands
- country
- prompt
- system name
- system-resource
- password
- reboot-schedule
- apmgmgtui ssh enable
- apmgmtui ssh port
- apmgmtui telnet- server enable
- apmgmtui http port
- apmgmtui http server
- apmgmtui http session-timeout
- apmgmtui https port
- apmgmtui https server
- apmgmtui snmp
- apmgmtip
- show apmanagement
- show system
- show system resource
- show version
- show config
- System Logging Commands
- System Clock Commands
- DHCP Relay Commands
- SNMP Commands
- snmp-server community
- snmp-server contact
- snmp-server location
- snmp-server enable server
- snmp-server host
- snmp-server trap
- snmp-server vacm view
- snmp-server vacm group
- snmp-server user
- snmp-server target
- snmp-server filter
- show snmp users
- show snmp target
- show snmp filter
- show snmp
- show snmp vacm view
- show snmp vacm group
- Flash/File Commands
- RADIUS Client Commands
- 802.1X Authentication Commands
- MAC Address Authentication Commands
- Filtering Commands
- Spanning Tree Commands
- bridge stp service
- bridge stp br-conf forwarding-delay
- bridge stp br-conf hello-time
- bridge stp br-conf max-age
- bridge stp br-conf priority
- bridge stp port-conf interface
- bridge-link path-cost
- bridge-link port- priority
- vap (STP Interface)
- path-cost (STP Interface)
- port-priority (STP Interface)
- bridge mac-aging
- show bridge stp
- show bridge br-conf
- show bridge port-conf interface
- show bridge status
- show bridge forward address
- show bridge mac- aging
- WDS Bridge Commands
- Ethernet Interface Commands
- Wireless Interface Commands
- interface wireless
- vap
- a-mpdu
- a-msdu
- channel
- transmit-power
- min-allowed-rate
- disable-coexist
- make-rf-setting- effective
- preamble
- short-guard-interval
- beacon-interval
- dtim-period
- rts-threshold
- ssid
- closed-system
- max-client
- max-association
- client-assoc-preempt
- assoc-timeout- interval
- auth-timeout-interval
- multicast-enhance
- shutdown (VAP)
- interfere-chan- recover
- antenna-chain
- long-distance
- long-distance reference-data
- long-distance slottime
- long-distance acktimeout
- long-distance ctstimeout
- bandwidth-control downlink
- bandwidth-control downlink rate
- bandwidth-control uplink
- bandwidth-control uplink rate
- show interface wireless
- show station
- show station statistics
- Wireless Security Commands
- Rogue AP Detection Commands
- Link Integrity Commands
- Link Layer Discovery Commands
- VLAN Commands
- WMM Commands
- QoS Commands
- Appendices
- Index of CLI Commands
- Index
– 109 –
9 Using the Command Line
Interface
When accessing the management interface for the over a direct connection to the
console port, or via a Telnet connection, the access point can be managed by
entering command keywords and parameters at the prompt. Using the access
point’s command-line interface (CLI) is very similar to entering commands on a
UNIX system.
Console Connection
To access the AP through the console port, first set up a console connection to the
AP. See “Console Port Connection” on page 19 for more information.
At the console prompt, enter the user name and password. (The default user name
is “admin” with no default password.) After the password is entered, the CLI displays
the “SMC#” prompt.
Example
(none) login: admin
Password:
Jan 1 11:33:13 login[1918]: root login on 'ttyS0'
SMC#
Note:
Command examples shown later in this chapter abbreviate the console
prompt to “AP” for simplicity.
Enter the necessary commands to complete your desired tasks.
When finished, exit the session with the “exit” command.