User's Manual
Table Of Contents
- Warranty and Product Registration
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Command Line Interface
- Using the Command Line Interface
- General Commands
- System Management Commands
- country
- prompt
- system name
- system-resource
- password
- reboot-schedule
- apmgmgtui ssh enable
- apmgmtui ssh port
- apmgmtui telnet- server enable
- apmgmtui http port
- apmgmtui http server
- apmgmtui http session-timeout
- apmgmtui https port
- apmgmtui https server
- apmgmtui snmp
- apmgmtip
- show apmanagement
- show system
- show system resource
- show version
- show config
- System Logging Commands
- System Clock Commands
- DHCP Relay Commands
- SNMP Commands
- snmp-server community
- snmp-server contact
- snmp-server location
- snmp-server enable server
- snmp-server host
- snmp-server trap
- snmp-server vacm view
- snmp-server vacm group
- snmp-server user
- snmp-server target
- snmp-server filter
- show snmp users
- show snmp target
- show snmp filter
- show snmp
- show snmp vacm view
- show snmp vacm group
- Flash/File Commands
- RADIUS Client Commands
- 802.1X Authentication Commands
- MAC Address Authentication Commands
- Filtering Commands
- Spanning Tree Commands
- bridge stp service
- bridge stp br-conf forwarding-delay
- bridge stp br-conf hello-time
- bridge stp br-conf max-age
- bridge stp br-conf priority
- bridge stp port-conf interface
- bridge-link path-cost
- bridge-link port- priority
- vap (STP Interface)
- path-cost (STP Interface)
- port-priority (STP Interface)
- bridge mac-aging
- show bridge stp
- show bridge br-conf
- show bridge port-conf interface
- show bridge status
- show bridge forward address
- show bridge mac- aging
- WDS Bridge Commands
- Ethernet Interface Commands
- Wireless Interface Commands
- interface wireless
- vap
- a-mpdu
- a-msdu
- channel
- transmit-power
- min-allowed-rate
- disable-coexist
- make-rf-setting- effective
- preamble
- short-guard-interval
- beacon-interval
- dtim-period
- rts-threshold
- ssid
- closed-system
- max-client
- max-association
- client-assoc-preempt
- assoc-timeout- interval
- auth-timeout-interval
- multicast-enhance
- shutdown (VAP)
- interfere-chan- recover
- antenna-chain
- long-distance
- long-distance reference-data
- long-distance slottime
- long-distance acktimeout
- long-distance ctstimeout
- bandwidth-control downlink
- bandwidth-control downlink rate
- bandwidth-control uplink
- bandwidth-control uplink rate
- show interface wireless
- show station
- show station statistics
- Wireless Security Commands
- Rogue AP Detection Commands
- Link Integrity Commands
- Link Layer Discovery Commands
- VLAN Commands
- WMM Commands
- QoS Commands
- Appendices
- Index of CLI Commands
- Index
Chapter 9
| Using the Command Line Interface
Telnet Connection
– 110 –
Telnet Connection
Telnet operates over the IP transport protocol. In this environment, your
management station and any network device you want to manage over the
network must have a valid IP address. If the access point does not acquire an IP
address from a DHCP server, the default IP address used by the access point is
192.168.2.10.
To access the AP through a Telnet session, you must first set the IP address for the
AP, and set the default gateway if you are managing the AP from a different IP
subnet. For example:
AP#configure
AP(config)#interface ethernet
AP(if-ethernet)#ip address 10.1.0.1 255.255.255.0 10.1.0.254
AP(if-ethernet)#
After you configure the access point with an IP address, you can open a Telnet
session by performing these steps.
1. From the remote host, enter the Telnet command and the IP address of the
device you want to access.
2. At the prompt, enter the user name and system password. The CLI will display
the “AP#” prompt to show that you are using executive access mode (that is,
Exec).
(none) login: admin
Password:
AP#
3. Enter the necessary commands to complete your desired tasks.
4. When finished, exit the session with the “quit” or “exit” command.
Note:
You can open up to four sessions to the device through Telnet.