User's Manual
Table Of Contents
- Warranty and Product Registration
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Command Line Interface
- Using the Command Line Interface
- General Commands
- System Management Commands
- country
- prompt
- system name
- system-resource
- password
- reboot-schedule
- apmgmgtui ssh enable
- apmgmtui ssh port
- apmgmtui telnet- server enable
- apmgmtui http port
- apmgmtui http server
- apmgmtui http session-timeout
- apmgmtui https port
- apmgmtui https server
- apmgmtui snmp
- apmgmtip
- show apmanagement
- show system
- show system resource
- show version
- show config
- System Logging Commands
- System Clock Commands
- DHCP Relay Commands
- SNMP Commands
- snmp-server community
- snmp-server contact
- snmp-server location
- snmp-server enable server
- snmp-server host
- snmp-server trap
- snmp-server vacm view
- snmp-server vacm group
- snmp-server user
- snmp-server target
- snmp-server filter
- show snmp users
- show snmp target
- show snmp filter
- show snmp
- show snmp vacm view
- show snmp vacm group
- Flash/File Commands
- RADIUS Client Commands
- 802.1X Authentication Commands
- MAC Address Authentication Commands
- Filtering Commands
- Spanning Tree Commands
- bridge stp service
- bridge stp br-conf forwarding-delay
- bridge stp br-conf hello-time
- bridge stp br-conf max-age
- bridge stp br-conf priority
- bridge stp port-conf interface
- bridge-link path-cost
- bridge-link port- priority
- vap (STP Interface)
- path-cost (STP Interface)
- port-priority (STP Interface)
- bridge mac-aging
- show bridge stp
- show bridge br-conf
- show bridge port-conf interface
- show bridge status
- show bridge forward address
- show bridge mac- aging
- WDS Bridge Commands
- Ethernet Interface Commands
- Wireless Interface Commands
- interface wireless
- vap
- a-mpdu
- a-msdu
- channel
- transmit-power
- min-allowed-rate
- disable-coexist
- make-rf-setting- effective
- preamble
- short-guard-interval
- beacon-interval
- dtim-period
- rts-threshold
- ssid
- closed-system
- max-client
- max-association
- client-assoc-preempt
- assoc-timeout- interval
- auth-timeout-interval
- multicast-enhance
- shutdown (VAP)
- interfere-chan- recover
- antenna-chain
- long-distance
- long-distance reference-data
- long-distance slottime
- long-distance acktimeout
- long-distance ctstimeout
- bandwidth-control downlink
- bandwidth-control downlink rate
- bandwidth-control uplink
- bandwidth-control uplink rate
- show interface wireless
- show station
- show station statistics
- Wireless Security Commands
- Rogue AP Detection Commands
- Link Integrity Commands
- Link Layer Discovery Commands
- VLAN Commands
- WMM Commands
- QoS Commands
- Appendices
- Index of CLI Commands
- Index
Chapter 25
| Wireless Security Commands
– 240 –
Example
AP(if-wireless 0: VAP[0])# make-security-effective
It will take several minutes !
Please wait a while...
device eth0 left promiscuous mode
br0: port 1(eth0) entering disabled state
br0: port 3(ath16) entering disabled state
br0: port 2(ath0) entering disabled state
device ath16 left promiscuous mode
br0: port 3(ath16) entering disabled state
device ath0 left promiscuous mode
br0: port 2(ath0) entering disabled state
wlan_vap_delete : enter. vaphandle=0x879a2000
wlan_vap_delete : exit. vaphandle=0x879a2000
wlan_vap_delete : enter. vaphandle=0x8729c000
wlan_vap_delete : exit. vaphandle=0x8729c000
device eth0 entered promiscuous mode
br0: port 1(eth0) entering forwarding state
wlan_vap_create : enter. devhandle=0x87ae8300, opmode=IEEE80211_M_HOSTAP,
flags=0x1
wlan_vap_create : exit. devhandle=0x87ae8300, opmode=IEEE80211_M_HOSTAP,
flags=0x1.
VAP device ath0 created
Setting Max Stations:17
DES SSID SET=EAP9112A_11BGN_0
ieee80211_ioctl_siwmode: imr.ifm_active=393856, new mode=3, valid=1
wlan_vap_create : enter. devhandle=0x87048300, opmode=IEEE80211_M_HOSTAP,
flags=0x1
wlan_vap_create : exit. devhandle=0x87048300, opmode=IEEE80211_M_HOSTAP,
flags=0x1.
VAP device ath16 created
Setting Max Stations:17
DES SSID SET=EAP9112A_11NA_0
ieee80211_ioctl_siwmode: imr.ifm_active=328320, new mode=3, valid=1
device ath0 entered promiscuous mode
br0: port 2(ath0) entering forwarding state
device ath16 entered promiscuous mode
br0: port 3(ath16) entering forwarding state
AP(if-wireless 0: VAP[0])#