User's Manual
Table Of Contents
- Warranty and Product Registration
- How to Use This Guide
- Contents
- Figures
- Tables
- Getting Started
- Web Configuration
- Command Line Interface
- Using the Command Line Interface
- General Commands
- System Management Commands
- country
- prompt
- system name
- system-resource
- password
- reboot-schedule
- apmgmgtui ssh enable
- apmgmtui ssh port
- apmgmtui telnet- server enable
- apmgmtui http port
- apmgmtui http server
- apmgmtui http session-timeout
- apmgmtui https port
- apmgmtui https server
- apmgmtui snmp
- apmgmtip
- show apmanagement
- show system
- show system resource
- show version
- show config
- System Logging Commands
- System Clock Commands
- DHCP Relay Commands
- SNMP Commands
- snmp-server community
- snmp-server contact
- snmp-server location
- snmp-server enable server
- snmp-server host
- snmp-server trap
- snmp-server vacm view
- snmp-server vacm group
- snmp-server user
- snmp-server target
- snmp-server filter
- show snmp users
- show snmp target
- show snmp filter
- show snmp
- show snmp vacm view
- show snmp vacm group
- Flash/File Commands
- RADIUS Client Commands
- 802.1X Authentication Commands
- MAC Address Authentication Commands
- Filtering Commands
- Spanning Tree Commands
- bridge stp service
- bridge stp br-conf forwarding-delay
- bridge stp br-conf hello-time
- bridge stp br-conf max-age
- bridge stp br-conf priority
- bridge stp port-conf interface
- bridge-link path-cost
- bridge-link port- priority
- vap (STP Interface)
- path-cost (STP Interface)
- port-priority (STP Interface)
- bridge mac-aging
- show bridge stp
- show bridge br-conf
- show bridge port-conf interface
- show bridge status
- show bridge forward address
- show bridge mac- aging
- WDS Bridge Commands
- Ethernet Interface Commands
- Wireless Interface Commands
- interface wireless
- vap
- a-mpdu
- a-msdu
- channel
- transmit-power
- min-allowed-rate
- disable-coexist
- make-rf-setting- effective
- preamble
- short-guard-interval
- beacon-interval
- dtim-period
- rts-threshold
- ssid
- closed-system
- max-client
- max-association
- client-assoc-preempt
- assoc-timeout- interval
- auth-timeout-interval
- multicast-enhance
- shutdown (VAP)
- interfere-chan- recover
- antenna-chain
- long-distance
- long-distance reference-data
- long-distance slottime
- long-distance acktimeout
- long-distance ctstimeout
- bandwidth-control downlink
- bandwidth-control downlink rate
- bandwidth-control uplink
- bandwidth-control uplink rate
- show interface wireless
- show station
- show station statistics
- Wireless Security Commands
- Rogue AP Detection Commands
- Link Integrity Commands
- Link Layer Discovery Commands
- VLAN Commands
- WMM Commands
- QoS Commands
- Appendices
- Index of CLI Commands
- Index
Chapter 31
| QoS Commands
– 266 –
Command Usage
◆ The AP supports eight QoS priority mapping templates, each identified by an
ID number (1 to 8). The templates also have user-defined name that can be
configured using the qos qos-template qos-template-name command.
◆ The QoS priority mapping templates can be configured using the qos qos-
template qos-template-priority command.
Example
AP(if-wireless 0: VAP[0])# qos 802.1d-802.1p mapping-template 3
This setting has not been effective !
If want to take effect, please execute make-security-effective command !
AP(if-wireless 0: VAP[0])#
qos 802.1d-dscp This command enables the mapping of WMM 802.1d priority values to IP DSCP
values on a VAP interface.
Syntax
qos 802.1d-dscp <enable | disable>
enable - Enables the mapping of WMM 802.1d to DSCP priority values.
disable - Disables the feature.
Default
Disabled
Command Mode
Interface Configuration (Wireless-VAP)
Command Usage
◆ This QoS feature requires a QoS mapping template to be configured using the
qos qos-template qos-template-priority command. The mapping template can
then be linked to the 802.1d-to-DSCP priority mapping using the qos 802.1d-
dscp mapping-template command.
◆ Both “802.1d to 802.1p” mapping and “802.1d to DSCP” mapping can be
enabled simultaneously when the default VLAN ID for the VAP is any other
value than 1. When only 802.1d-to-DSCP mapping is enabled, the default VLAN
ID for the VAP must be set to 1.
Example
AP(if-wireless 0: VAP[0])# qos 802.1d-dscp enable
This setting has not been effective !
If want to take effect, please execute make-security-effective command !