0/100Mbps Fast Ethernet Switch User Manual RECYCLABLE 1
Chapter 1 INTRODUCTION 1.1 Product Briefs The switch is a un-management 10/100Mbps switch, the Fast desktop switches provides 5/8/16/24 10/100Mbps auto-negotiation ports, all ports support Auto MDI / MDIX feature. Ideally designed for SOHO and small workgroup networking connection, Simple and easy installation, it eliminates networks bottleneck while giving users flexibility and scalability. 1.2 Product Features Table 1-1 Ethernet Switch Product Features Item Description Standard IEEE 802.
Network 10Base-T: Cables Category 3/4/5 shielded twisted pair (STP) with the maximum transmission distance of 100 m 100Base-TX: Category 5 STP with the maximum transmission distance of 100 m 1.3 Physical & Environmental Table 1-2 Ethernet Switch Environmental Features Temperature Humidity System cooling Operating: 0° ~ 40° C (32℉ to 104℉) Storage: -10° ~ 70° C (14℉ to 158℉) Operating: 10% ~ 90% RH, non-condensing Storage: 5% ~ 90% RH, non-condensing Air cooling 1.4 Hardware Introduction 1.4.
5/8-Port 10/100Mbps Switch Front Panel 16/24-Port 10/100Mbps Switch Front Panel 2．Rear Panel The figure below shows the rear panel of the Switch. All MDI/MDI-X ports and an external DC power adapter jack in the 5/8-port rear panel. There is a AC inlet in the 16/24-Port switch rear panel.
Auto MDI/MDI-X Ports: All ports support automatic MDI/MDI-X crossover detection. The Auto MDI/MDI-X function makes it simple to connect to the switch—just plug either a Crossover or Straight-Through CAT5 cable into any port. DC Power Jack: Power is supplied through an external DC power adapter. Check the technical specification section for information about the DC power input voltage. AC inlet Power is supplied through external AC power. The input AC voltage is 100~240V. 1.3.
Chapter 2 CONNECTING THE SWITCH z PC to Switch A computer can be connected to the 8-Port 10/100Mbps Switch via a two-pair Category 3, 4, 5 UTP/STP Straight-Through or Crossover cable. A computer equipped with a RJ-45 10/100Mbps port can be connected to any of the eight 8-Port 10/100Mbps Switch ports. The LED indicators for the PC connection depend on the capability of the computer’s Ethernet card.
z Switch to other devices The 8-Port 10/100Mbps Switch can be connected to another switch or other devices (routers, bridges, etc.) via a two-pair Category 3, 4, 5 UTP/STP Straight-Through or Crossover cable. A Category 5 cable must be used for 100Mbps operation. The connection can be accomplished from any (MDI-X) port on the 8-Port 10/100Mbps Switch to any of the 10Mbps or 100Mbps (MDI-X) ports on another switch or other devices.
Chapter 3 MOUNTING THE SWITCH ON A WALL The 8-Port 10/100Mbps Switch can also be mounted on a wall. Two mounting slots are provided on the bottom of the switch for this purpose. Please make sure that the front panel is exposed in order to view the LEDs. Please refer to the illustration below: A.) Mounting on a cement wall 1. Mount the Nylon screw anchors into a cement wall. 2. Drive the T3 x 15L screws into the Nylon screw anchors. 3.
Annex RJ-45 PIN SPECIFICATION The following diagram and tables show the standard RJ-45 receptacle/connector and their pin assignments.
FCC 6WDWHPHQW Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
