54V, 72W DC Power Supply with UPS and PoE Model: EP-54V-72W
Introduction Thank you for purchasing the Ubiquiti Networks® EdgePower™. This Quick Start Guide is designed to guide you through installation and also includes warranty terms. Package Contents EdgePower EP-54V-72W Mount Brackets (Qty. 2) Power Cord Bracket Screws (Qty. 8) Power Cable with DC Jack Wall Mount Screws (Qty. 2) Wall Mount Anchors (Qty.
Hardware Overview Front Panel Ports DC Out Battery In Power RJ45 Ports 1-2 Interface Description RJ45 1-2 RJ45 switch ports support 10/100 Ethernet connections and 54V Passive Power over Ethernet (PoE) output. DC Out Connect the Power Cable with DC Jack to this terminal block for 54V, 1.3A output. Battery In Optional: Connect the Power Cable with Ring Terminals to a 12V lead acid battery (not included). Power Connect the included Power Cord.
Front Panel Button Reset Button Description To reset to factory defaults: Reset 1. Disconnect power from the EdgePower. 2. Reconnect power while holding the Reset button. The port LEDs will repeatedly light up in sequential order (this takes approximately 5 seconds). 3. When both port LEDs flash twice at the same time, release the Reset button.
Front Panel LEDs System System LED State Status Flashing White Bootup in progress. White Ready for use, not connected to Ubiquiti® Network Management System (UNMS™). Blue Ready for use, connected to UNMS. Steady Blue with Occasional Flashing Ready for use, unable to connect to UNMS, check connection to UNMS server. Quickly Flashing Blue Used to locate a device in UNMS. Alternating Blue/White Firmware upgrade in progress.
RJ45 LEDs PoE LED Link/Act State Status Off No Power over Ethernet Amber 54V Power over Ethernet Off No Link Amber Link Established at 10/100 Mbps Amber Flashing Link Activity at 10/100 Mbps PoE Link/ Activity
Hardware Installation The EdgePower can be mounted on a horizontal surface, mounted on a vertical surface, or mounted in a rack (rackmount accessory not included). WARNING: The EdgePower must not be stacked. Do not place it on top of another device. Do not place anything on top of the EdgePower. WARNING: FAILURE TO PROVIDE PROPER VENTILATION MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF CLEARANCE NEXT TO THE VENTILATION HOLES FOR ADEQUATE AIRFLOW.
2. Connect the other end of the Power Cord to a power outlet. Using the Battery Input (Optional) For redundant power backup, connect an external battery (not included) to the EdgePower. Note: Only one power source can be used at any one time. With both power sources connected, the AC input will be used; the battery input defaults to backup. 1. Connect the 3-pin terminal block connector of the Power Cable with Ring Terminals to the Battery In port. 2.
Connecting Ethernet 1. Connect an Ethernet cable from your 54V PoE device(s) to ports 1-2 on the EdgePower. WARNING: Before enabling PoE out in the EdgePower Configuration Interface, ensure that the connected PoE device supports 54V Passive PoE. Connecting DC Output 1. Connect the 3-pin terminal block connector of the Power Cable with DC Jack to the DC Out port. 2. Connect the other end of the DC/DC power cable to a device with a DC jack.
Accessing the Configuration Interface Access the EdgePower Configuration Interface to monitor status and power consumption, or to configure 54V Passive PoE and network settings. Note: The EdgePower is set to DHCP by default with a fallback IP address of 192.168.1.20. 1. Launch your web browser. Type the appropriate IP address in the address field. Press enter (PC) or return (Mac). https://192.168.1.20 2. The login screen will appear. Enter ubnt in the Username and Password fields. Click Login.
Configuring PoE Settings The PoE setting for ports 1-2 is set to Off by default. WARNING: Before activating PoE, ensure that the connected device supports passive PoE and the supplied voltage. 1. In the EdgePower Configuration Interface, click the Power tab. 2. For the appropriate port, click to enable 54V Passive PoE. 3. Click Save Changes.
Specifications EP-54V-72W Dimensions 115 x 192 x 43.7 mm (4.53 x 7.56 x 1.72") Weight Interfaces Networking Management PoE Output 650 g (1.43 lb) (2) 10/100 Mbps RJ45 Ports Ethernet In-Band (2) 54VDC Passive PoE (Pins 4, 5+; 7, 8-) DC Output 54V, 1.3A Power Method AC Input Battery Input 100-240VAC, 50-60 Hz, Universal Input DC Terminal Block Power Supply AC Input Battery Input AC/DC 72W 12VDC Lead Acid Battery* Max.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Failure to provide proper ventilation may cause fire hazard. Keep at least 20 mm of clearance next to the ventilation holes for adequate airflow. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. WARNING: Do not use this product in location that can be submerged by water.
Limited Warranty www.ubnt.com/support/warranty/ The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions. Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity български [Bulgarian] С настоящото UBIQUITI NETWORKS декларира, че това устройство EP-54V-72W е в съответствие със съществените изисквания и други приложими разпоредби на Директиви 2014/30/ЕС, 2014/35/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: www.ubnt.
Italiano [Italian] Con la presente, UBIQUITI NETWORKS, dichiara che questo dispositivo EP-54V-72W, è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti delle direttive 2014/30/UE, 2014/35/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: www.ubnt.
www.ubnt.com Ubiquiti Networks, Inc. 685 Third Avenue, 27th Floor New York, NY 10017 USA ©2018-2019 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, EdgeMAX, EdgeOS, EdgePower, TOUGHCable, and UNMS are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries.
