Beverage Cooler BWC120SLD Owner’s Manual For more information on other great EdgeStar products on the web, go to http://www.edgestar.
Important Safety Information Improper handling can cause serious damage to the EdgeStar beverage cooler and/or injury to the user. This beverage cooler is designed for domestic indoor use only. Do not use the unit for industrial or commercial use. Any other use may invalidate the warranty. Please review the ratings label located on the rear panel of the unit for electrical and other technical data related to this unit. The unit must be used in a properly grounded wall outlet.
Table of Contents IMPORTANT SAFETY INFORMATION ................................................................. I INTRODUCTION ................................................................................................... 1 PARTS IDENTIFICATION ..................................................................................... 2 BACK VIEW .......................................................................................................... 2 FRONT VIEW ...........................................
Introduction Thank you for purchasing this EdgeStar beverage cooler. We are glad you chose us. We believe that your purchase of this product opens a relationship between you and EdgeStar. We will provide the customer support needed to nurture that relationship. This manual contains important information regarding the proper installation, use and maintenance of your beverage cooler. Following this manual will ensure that your product will work at its peak performance and efficiency.
Parts Identification Front View Internal Fan Control Panel Switch for Internal Light Recessed Handle Shelf Door Compressor Step Leveling Foot Back View Tip: Gather the model and serial number from the product label and write them down before installing the beverage cooler.
Installing the Beverage Cooler The beverage cooler should be installed in accordance with local electrical code requirements. The beverage cooler should also be placed in a location that is strong enough to support its total weight, keeping in mind that it will weigh substantially more when fully loaded than when empty. Before you plug the beverage cooler into a power supply, be sure to let it stand upright for at least 24 hours to allow the compressor’s oils to settle.
Electrical Requirements ELECTRIC SHOCK HAZARD! Plug into a grounded 3-prong outlet. Never remove the grounding prong from the plug. Never use an adapter to bypass the grounding prong. DO NOT use an extension cord. Failure to follow these instructions can result in fire, electrical shock, or death.
Reversing the Door Swing Hinge Cover Screws Top hinge Cabinet Door Tools needed: flathead screwdriver, Phillips screwdriver IMPORTANT: Before you begin, unplug the beverage cooler from power. To remove the door: 1. Using a flathead screw driver carefully pry the top hinge cover off. 2. Using a Phillips screwdriver, remove the screws and take off top hinge. Keep the parts together and set them aside. 3. Lift the door off the bottom hinge and set the door aside. 4.
Normal Sounds Your new beverage cooler may make sounds that are not familiar to you. Most of the new sounds are normal. Hard surfaces like the floor, walls can make the sounds seem louder than they actually are. The following describes the kinds of sounds that might be new to you and what may be making them. Ratting noises may come from the flow of the refrigerant or the water line, Items stored on top of the beverage cooler can also make noises.
CLEANING AND MAINTENANCE Periodic cleaning and proper maintenance will ensure efficiency, top performance, and long life. Exterior Cleaning The door and cabinet may be cleaned with a mild detergent and lukewarm water solution such as 2 tablespoons of baking soda to 1 quart of water. Do not use solvent based or abrasive cleaners. Use a soft sponge and rinse with clean water. Wipe with a soft clean towel to prevent water spotting.
Troubleshooting continued Issue The beverage cooler does not turn on. The beverage cooler will not reach the desired temperature Possible cause Solution There is a power failure. Ensure the cooler is plugged in and the power outlet has power. The cooler is not plugged in. Plug the unit in to a power outlet that has sufficient amperage. A house fuse has blown or the circuit breaker is tripped. Replace the broken fuse in your fuse box or reset the breaker.
Specifications Description of product Freestanding Beverage Cooler Model BWC120SLD Voltage/Frequency AC 115V~60Hz Amperage 1.2 Amps Color Black Cabinet; Stainless Steel Door Temperature Range 32ºF - 46ºF Refrigerant R600a, 24g Dimensions (Height x Width x Depth ) 20.1" x 17.52" x 32.72" Weight 63.8 pounds Note: Technical data and performance information is provided for reference only. Specifications are subject to change.
EdgeStar Limited Warranty One (1) Year Parts & Ninety (90) Days Labor This product is warranted by EdgeStar to be free from defective workmanship and materials, subject to any conditions set forth as follows: WHAT IS COVERED: LABOR: For a period of NINETY (90) DAYS from the date of original purchase, labor will be performed free of charge at an authorized EdgeStar repair facility.
EdgeStar Products 500 N. Capital of TX Hwy, Bldg 5 Austin, TX 78746 Toll Free: 1-866-319-5473 Web: http://www.edgestar.com E-mail: service@edgestar.com Register your product, download owner’s manuals, access additional troubleshooting resources, and obtain more information on other great EdgeStar products on the web at: http://www.edgestar.com Product contents and specifications may change without notice. Copyright © 2015 Living Direct, Inc. All rights reserved.