® eC ilt-i C 15 S Owner's Manual For more information on other great EdgeStar products on the web, go to http.//www, edgestar.
important Safety information Improper handling can cause serious damage to the EdgeStar beverage cooler and/or injury to the user. This beverage cooler is designed for domestic indoor use only. Do not use the unit for industrial or commercial use. Any other use may invalidate the warranty. Please review the ratings label located on the rear panel of the unit for electrical and other technical data related to this unit. The unit must be used in a properly grounded wall outlet.
Table of Contents iMPORTANT SAFETY iNFORMATiON ................................................................. INTRODUCTION ................................................................................................... PARTS IDENTIFICATION ..................................................................................... BACK Vl EW.......................................................................................................... FRONT VIEW ...............................................
Introduction Thank you for purchasing this EdgeStar beverage cooler. We are glad you chose us. We believe that your purchase of this product opens a relationship between you and EdgeStar. We will provide the customer support needed to nurture that relationship. This manual contains important information regarding the proper installation, use and maintenance of your beverage cooler. Following this manual will ensure that your product will work at its peak performance and efficiency.
Parts identification Top Right Hinge Front View Control Panel Internal Carbon Filter Fan J " Shelf Door Handle Stainless Steel Door Note: The carbon filter should be replaced every 3-6 months depending on the unit's exposure level to odor.
Installing the Beverage Cooler The beverage cooler should be installed in accordance with local electrical code requirements. The beverage cooler should also be placed in a location that is strong enough to support its total weight, keeping in mind that it will weigh substantially more when fully loaded than when empty. Before you plug the beverage cooler into a power supply, be sure to let it stand upright for at least 24 hours to allow the compressor's oils to settle.
installation Clearance Requirements When installing the beverage cooler under a counter, recommended spacing dimensions shown. follow the , To ensure proper service access and ventilation, allow at least 2" to 3" clearance at the back. The installation should allow the unit to be pulled forward for servicing, if necessary. Important - Choose Notes: a location that has ambient temperatures above 50°F and below 95°F.
Electrical Requirements ELECTR|C SHOCK • Plug into a grounded • Never remove H_RB_ 3=prong outlet. the grounding prong from the plug. Never use an adapter to bypass the grounding DO NOT use an extension cord. • Failure to follow electrical these instructions can result prong. in fire, shock, or death.
installing the Door Handle To install the door handle: 1. Open the door and carefully pull the door gasket where the handle is to be installed. around the area 2. Carefully remove the two pre-installed decorative plugs from the front of the door. Note: some beverage coolers do not have decorative plugs installed. 3. Insert each Phillips head screw through the gasket side of the door until the screw pass through the door. 4.
Reversing the Door Swing Follow the instructions below to reverse the door swing. IMPORTANT: Before you begin, unplug the refrigerator. J To reverse the door from right swing to left swing: 1. Open the door and using a Phillips screwdriver, remove the bottom screws from the lower hinge. 2. Carefully slide the bottom of the door forward and down, and place it on a padded surface to prevent damaging it. 3. Remove the screws from the upper right hinge.
OPERATION Installation Check List before Operation 1. Have all packing materials and tape been removed from the interior and exterior of the beverage cooler? 2. Have the installation instructions been followed, including connecting the machine to electricity? And has proper grounding been installed for the beverage cooler? 3. Has the machine been leveled? 4. is the beverage cooler in a site where the ambient temperature is between 50 ° F and 95 ° F all year round? 5.
Normal Sounds Your new beverage cooler may make sounds that are not familiar to you. Most of the new sounds are normal. Hard surfaces like the floor, walls can make the sounds seem louder than they actually are. The following describes the kinds of sounds that might be new to you and what may be making them. • Rattling noises may come from the flow of the refrigerant or the water line, Items stored on top of the beverage cooler can also make noises.
CLEANING AND MAINTENANCE Periodic cleaning and proper maintenance performance, and long life. Exterior will ensure efficiency, top Cleaning The door and cabinet may be cleaned with a mild detergent and lukewarm water solution such as 2 tablespoons of baking soda to 1 quart of water. Do not use solvent based or abrasive cleaners. Use a soft sponge and rinse with clean water. Wipe with a soft clean towel to prevent water spotting.
Troublesh issue The beverage cooler does not turn on. The beverage cooler will not reach the desired temperature oo ting con tin ued Possible cause Solution There is a power failure. Ensure the cooler is plugged in and the power outlet has power. The cooler is not plugged in. Plug the unit in to a power outlet that has sufficient amperage. A house fuse has blown or the circuit breaker is tripped. Replace the broken fuse in your fuse box or reset the breaker.
Specifications Description of product Built=in Beverage Model CBR1501SG Voltage/Frequency AC 115V~60Hz Amperage 1.8A Input Power 130W Color Black Cabinet; Door Storage Capacity Refrigerant Temperature Stainless Steel 160 Cans* R134a, 1.84 oz. Range Dimensions (Height Cooler 38 = 50°F 33 1/2"x 23 1/2"x 22 1/2" x Width x Depth ) Weight Note: Technical reference only. 100 pounds data and performance information is provided for Specifications are subject to change.
This product is warranted by EdgeStar and is subject to any conditions WHAT IS COVERED: WHAT IS NOT COVEREDcoverage For a period of ONE (1) YEARfrom the date of original retail purchase, EdgeStar will repair or replace any part free of charge including labor that fails due to a defect in materials or workmanship. Labor will be performed free of charge at an authorized EdgeStar repair facility and EdgeStar will supply new, rebuilt, or refurbished parts free of charge.
ED, GES EdgeStar Products 500 N. Capital of TX Hwy, Austin, TX 78746 BIdg 5 Toll Free: 1-866-319-5473 Web: http://www.edgestar.com E-mail: service@edgestar.com Register your product, resources, and obtain http://www.edgesfar.com download owner's manuals, access additional troubleshooting more information on other great EdgeStar products on the web at: Product contents Copyright and specifications may change without @ 2013 Living Direct, Inc. All rights reserved. notice.