Built-in Beverage Cooler CBR1501SG Owner’s Manual For more information on other great EdgeStar products on the web, go to http://www.edgestar.
Important Safety Information Improper handling can cause serious damage to the EdgeStar beverage cooler and/or injury to the user. This beverage cooler is designed for domestic indoor use only. Do not use the unit for industrial or commercial use. Any other use may invalidate the warranty. Please review the ratings label located on the rear panel of the unit for electrical and other technical data related to this unit. The unit must be used in a properly grounded wall outlet.
Table of Contents IMPORTANT SAFETY INFORMATION ................................................................. I INTRODUCTION ................................................................................................... 1 PARTS IDENTIFICATION ..................................................................................... 2 BACK VIEW .......................................................................................................... 2 FRONT VIEW ...........................................
Introduction Thank you for purchasing this EdgeStar beverage cooler. We are glad you chose us. We believe that your purchase of this product opens a relationship between you and EdgeStar. We will provide the customer support needed to nurture that relationship. This manual contains important information regarding the proper installation, use and maintenance of your beverage cooler. Following this manual will ensure that your product will work at its peak performance and efficiency.
Parts Identification Top Right Hinge Front View Control Panel Internal Fan Carbon Filter Shelf Door Handle Stainless Steel Door Note: The carbon filter should be replaced every 3-6 months depending on the unit’s exposure level to odor. If the unit is placed in the kitchen regular replacement every 3 months is ideal. Lock Front vent Leveling foot Back View Product Label Tip: Gather the model and serial number from the product label and write them down before installing the beverage cooler.
Installing the Beverage Cooler The beverage cooler should be installed in accordance with local electrical code requirements. The beverage cooler should also be placed in a location that is strong enough to support its total weight, keeping in mind that it will weigh substantially more when fully loaded than when empty. Before you plug the beverage cooler into a power supply, be sure to let it stand upright for at least 24 hours to allow the compressor’s oils to settle.
Installation Clearance Requirements When installing the beverage cooler under a counter, follow the recommended spacing dimensions shown. • To ensure proper service access and ventilation, allow at least 2/5” clearance at the back, 1/5” at top and 1/5” at sides. The installation should allow the unit to be pulled forward for servicing, if necessary. Top View Important Notes: 2/5” • Choose a location that has ambient temperatures above 50°F and below 95°F.
Electrical Requirements ELECTRIC SHOCK HAZARD! Plug into a grounded 3-prong outlet. Never remove the grounding prong from the plug. Never use an adapter to bypass the grounding prong. DO NOT use an extension cord. Failure to follow these instructions can result in fire, electrical shock, or death.
Installing the Door Handle To install the door handle: 1. Open the door and carefully pull the door gasket around the area where the handle is to be installed. 2. Carefully remove the two pre-installed decorative plugs from the front of the door. Note: some beverage coolers do not have decorative plugs installed. 3. Insert each Phillips head screw through the gasket side of the door until the screw pass through the door. 4.
Reversing the Door Swing Follow the instructions below to reverse the door swing. IMPORTANT: Before you begin, unplug the refrigerator. To reverse the door from right swing to left swing: 1. Open the door and using a Phillips screwdriver, remove the bottom screws from the lower hinge. 2. Carefully slide the bottom of the door forward and down, and place it on a padded surface to prevent damaging it. 3. Remove the screws from the upper right hinge.
OPERATION Installation Check List before Operation 1. Have all packing materials and tape been removed from the interior and exterior of the beverage cooler? 2. Have the installation instructions been followed, including connecting the machine to electricity? And has proper grounding been installed for the beverage cooler? 3. Has the machine been leveled? 4. Is the beverage cooler in a site where the ambient temperature is between 50º F and 95º F all year round? 5.
Normal Sounds Your new beverage cooler may make sounds that are not familiar to you. Most of the new sounds are normal. Hard surfaces like the floor, walls can make the sounds seem louder than they actually are. The following describes the kinds of sounds that might be new to you and what may be making them. Rattling noises may come from the flow of the refrigerant or the water line, Items stored on top of the beverage cooler can also make noises.
CLEANING AND MAINTENANCE Periodic cleaning and proper maintenance will ensure efficiency, top performance, and long life. Exterior Cleaning The door and cabinet may be cleaned with a mild detergent and lukewarm water solution such as 2 tablespoons of baking soda to 1 quart of water. Do not use solvent based or abrasive cleaners. Use a soft sponge and rinse with clean water. Wipe with a soft clean towel to prevent water spotting.
Troubleshooting continued Issue The beverage cooler does not turn on. The beverage cooler will not reach the desired temperature Possible cause Solution There is a power failure. Ensure the cooler is plugged in and the power outlet has power. The cooler is not plugged in. Plug the unit in to a power outlet that has sufficient amperage. A house fuse has blown or the circuit breaker is tripped. Replace the broken fuse in your fuse box or reset the breaker.
Specifications Description of product Built-in Beverage Cooler Model CBR1501SG Voltage/Frequency AC 115V~60Hz Amperage 1.8A Input Power 130W Color Black Cabinet; Stainless Steel Door Storage Capacity 160 Cans* Refrigerant R134a, 1.84 oz. Temperature Range 38 - 50ºF Dimensions (Height x Width x Depth ) 33 1/2” x 23 1/2” x 22 1/2” Weight 100 pounds Note: Technical data and performance information is provided for reference only. Specifications are subject to change.
Limited Warranty: Full One-Year Parts and Labor This product is warranted by EdgeStar and is subject to any conditions set forth as follows: WHAT IS COVERED: For a period of ONE (1) YEAR from the date of original retail purchase, EdgeStar will repair or replace any part free of charge including labor that fails due to a defect in materials or workmanship.
EdgeStar Products 500 N. Capital of TX Hwy, Bldg 5 Austin, TX 78746 Toll Free: 1-866-319-5473 Web: http://www.edgestar.com E-mail: service@edgestar.com Register your product, download owner’s manuals, access additional troubleshooting resources, and obtain more information on other great EdgeStar products on the web at: http://www.edgestar.com Product contents and specifications may change without notice. Copyright © 2011 Living Direct, Inc. All rights reserved.
