Built-in Outdoor Beverage Cooler CBR1501SSOD Owner’s Manual For more information on other great EdgeStar products on the web, go to http://www.edgestar.com To use the EdgeStar self-diagnostic tool, go to https://support.edgestar.com V2.
Important Safety Information Improper handling can cause serious damage to the EdgeStar beverage cooler and / or injury to the user. This beverage cooler is designed for domestic indoor use only. Do not use the unit for industrial or commercial use. Any other use may invalidate the warranty. Please review the ratings label located on the rear panel of the unit for electrical and other technical data related to this unit. The unit must be used in a properly grounded wall outlet.
General Safety To prevent back and other types of injuries, use at least two people to move and install the beverage cooler. This appliance is not intended for use by persons, including children, with reduced physical, sensory or mental capabilities, unless they have been given supervision or instruction concerning the use of the appliance by the person(s) responsible for their safety.
Table of Contents IMPORTANT SAFETY INFORMATION……………………………………………………………………………………... I TABLE OF CONTENTS……………………………………………………………………………………………………….. III FIRST TIME OPERATING INSTRUCTIONS…………………………………………………………………………………………. 1 INTRODUCTION……………………………………………………………………………………………………………….. 1 PARTS IDENTIFICATION…………………………………………………………………………………………………….. 2 FRONT VIEW……………………………………………………………………………………………………………………… 2 BACK VIEW………………………………………………………………………………………………………………………..
First Time Operating Instructions Before use, make sure all packaging labels and materials are removed from the unit. Be sure to keep track of all included parts and pieces before discarding packaging materials. It is advised that you keep the original box and packaging materials in case you ever need to move or ship the appliance in the future. Let the unit stand for at least 24 hours before you use it; this allows the cooling components time to settle from transit.
Parts Identification Tip: Gather the model and serial number from the product label and write them down before installing the beverage cooler. Note: The carbon filter should be replaced every 3 – 6 months depending on the unit’s exposure level to odor. If the unit is located in the kitchen, regular replacement every 3 months is ideal.
Installing the Beverage cooler The beverage cooler should be installed in accordance with local electrical code requirements. The beverage cooler should also be placed in a location that is strong enough to support its total weight, keeping in mind that it will weigh substantially more when fully loaded than when empty. Before you plug the beverage cooler into a power supply, be sure to let it stand upright for at least 24 hours to allow the compressor’s oils to settle.
Installation Clearance Requirements Important Notes: Choose a location that has ambient temperatures above 50° F and below 95° F. Operation outside these temperatures may result in lowered efficiency or cause other adverse effects. This unit MUST be installed in an area protected from the elements, e.g. wind, rain, water spray or drips. The beverage cooler should not be located next to ovens, grills, or other high heat sources.
Electrical Requirements ELECTRIC SHOCK HAZARD! Plug into a grounded 3-prong outlet. Never remove the grounding prong from the plug. Never use an adapter to bypass the grounding prong. DO NOT use an extension cord. Failure to follow these instructions can result in fire, electrical shock, or death.
Installing the Door Handle To install the door handle: 1. Remove the four screws from the side of the door. This should be the side opposite of the door hinge. 2. Place and align the openings of the handle hinges over the screw holes. 3. Insert and tighten the screws to hold the handle in place. Caution: Do not over-tighten the screws as this may cause damage to the handle or to the stainless steel door.
Reversing the Door Swing Follow the instructions below to reverse the door swing. Important: Before you begin, unplug the refrigerator. To Reverse the Door from Right Swing to Left Swing 1. Open the door and using a Philips Screwdriver, remove the bottom screws from the lower hinge. 2. Carefully slide the bottom of the door forward and down, and place it on a padded surface to prevent damaging it. 3. Remove the screws from the upper right hinge.
4. Remove the lower hinge and bushing from the bottom right support bracket. Remove the decorative screws from the left corner of the door and install and tighten them to the right corner holes. Remove the plastic cap from the top left corner of the door and insert it on the top right corner. 5. Install the lower hinge and bushing on the bottom left support bracket. 6.
Using the Temperature Control Panel Use the up and down buttons to adjust the temperature. The temperature can be displayed in Fahrenheit or Celsius. This beverage cooler has a temperature range from 38° F to 50° F. Note: Whether your beverage cooler can reach the actual set temperature depends on the ambient environmental conditions. This beverage cooler has two displays: a Set Display that shows the set temperature, and a Current Temperature Display that shows the current temperature.
Normal Sounds Your new beverage cooler may make sounds that are not familiar to you. Most of the new sounds are normal. Hard surfaces like the floor and walls can make the sounds seem louder than they actually are. The following describes the kinds of sounds that might be new to you and what may be making them. Rattling noises may come from the flow of the refrigerant or the water line. Items stored on top of the beverage cooler can also make noises.
Cleaning and Maintenance Periodic cleaning and proper maintenance will ensure efficiency, top performance, and long life. Exterior Cleaning The door and cabinet may be cleaned with a mild detergent and lukewarm water solution such as 2 tablespoons of baking soda to 1 quart of water. Do not use solvent based or abrasive cleaners. Use a soft sponge and rinse with clean water. Wipe with a soft clean towel to prevent water spotting.
Troubleshooting Before Calling for Help If the unit appears to be malfunctioning, read through the “Operation” section of this manual first. If the problem persists, check the Troubleshooting Guide below and on the following page. The problem may be something that can easily be solved or explained. Symptoms The beverage cooler turns on and off frequently. Possible Causes The room temperature is higher than the recommended ambient environment. The door is being opened too often.
Symptoms The body of the beverage cooler is electrified. Possible Causes The unit is not grounded properly. Frost is forming in the beverage cooler. The environment is humid. The ambient temperature is too low. The door is being opened too frequently. The door will not shut properly. The cooler is not level. The door gasket is dirty. The door gasket is not installed correctly. The shelves are incorrectly installed. 13 Solutions Contact your local electrician to test your electrical grounding system.
Specifications Note: Technical data and performance information are provided for reference only. Specifications are subject to change. Check the rating label on the beverage cooler for the most accurate information. Description of product Built-in Beverage cooler Model CBR1501SSOD Voltage / Frequency AC 115V~60Hz Amperage 1.1 A Input Power 120 W Color Stainless Steel Cabinet; Stainless Steel Door Storage Capacity 142 Cans* Refrigerant R600a, 1.4 oz.
EdgeStar Limited Warranty Full One-Year Parts and Labor WHAT IS COVERED: This product is warranted by EdgeStar and is subject to any conditions set forth as follows: For a period of ONE (1) YEAR from the date of original retail purchase, EdgeStar will repair or replace any part free of charge including labor that fails due to a defect in materials or workmanship.