Built-in Wine and Beverage Cooler CWB7016DZ Owner’s Manual For more information on other great EdgeStar products on the web, go to http://www.edgestar.
Important Safety Information Improper handling can cause serious damage to the EdgeStar wine and beverage cooler and/or injury to the user. This wine and beverage cooler is designed for domestic indoor use only. Do not use the unit for industrial or commercial use. Any other use may invalidate the warranty. Please review the ratings label located on the rear panel of the unit for electrical and other technical data related to this unit. The unit must be used in a properly grounded wall outlet.
Table of Contents IMPORTANT SAFETY INFORMATION ................................................................. I INTRODUCTION ................................................................................................... 1 PARTS IDENTIFICATION ..................................................................................... 2 BACK VIEW .......................................................................................................... 2 FRONT VIEW ...........................................
Introduction Thank you for purchasing this EdgeStar wine and beverage cooler. We are glad you chose us. We believe that your purchase of this product opens a relationship between you and EdgeStar. We will provide the customer support needed to nurture that relationship. This manual contains important information regarding the proper installation, use and maintenance of your wine and beverage cooler. Following this manual will ensure that your product will work at its peak performance and efficiency.
Parts Identification Front View Top Right Hinge Stainless Steel Door Control Panel Internal Fan Door Handle Front Vent Lock Leveling foot Back View Product Label Tip: Gather the model and serial number from the product label and write them down before installing the wine and beverage cooler.
Installing the Wine and Beverage Cooler The wine and beverage cooler should be installed in accordance with local electrical code requirements. The wine and beverage cooler should also be placed in a location that is strong enough to support its total weight, keeping in mind that it will weigh substantially more when fully loaded than when empty. Before you plug the wine and beverage cooler into a power supply, be sure to let it stand upright for at least 24 hours to allow the compressor’s oils to settle.
Installation Clearance Requirements When installing the wine and beverage cooler under a counter, follow the recommended spacing dimensions shown. • To ensure proper service access and ventilation, allow at least 2-3” of clearance at the back of the unit. The installation should allow the unit to be pulled forward for servicing, if necessary. Important Notes: Side View • Choose a location that has ambient temperatures above 65°F and below 90°F.
Electrical Requirements ELECTRIC SHOCK HAZARD! Plug into a grounded 3-prong outlet. Never remove the grounding prong from the plug. Never use an adapter to bypass the grounding prong. DO NOT use an extension cord. Failure to follow these instructions can result in fire, electrical shock, or death.
Installing and Removing the Shelves To prevent damaging the door gasket, make sure to open the door all the way before pulling the shelves out of their track. To install the shelves: 1. Open the door completely. 2. Slide the shelf on the shelf track and slowly push back until it stops. 3. Push down on the front of the shelf to allow the back of the shelf to lift over the plastic post. (Imagine a seesaw movement.
Reversing the Door Swing Follow the instructions below to reverse the door swing. IMPORTANT: Before you begin, unplug the wine and beverage cooler. It is recommended that two people perform the steps below. To reverse the door from right swing to left swing: 1. Remove the two screws from the front vent with a Phillips screwdriver. See Figure 1. Then, remove the front vent cover. This will expose the bottom hinge. Figure 1 2.
. Place the hinge cover over the upper left hinge. 12. Install the three black capped screws from step 8 into the three exposed holes located on the top right of the cabinet. 13. Reinstall the front vent cover. 14. Hand tighten the stainless steel screw from step 2 to cover the hole in the middle of the top of the door.
OPERATION Using the Temperature Control Panel Upper Zone Lower Zone Note: The scale of the control panel in this image has been compressed to fit this manual. Each zone is independently controlled by the touchpad controls that are located on the center divider (pictured above). The temperature display can be in Fahrenheit or Celsius. Each zone of this wine and beverage cooler has a temperature range from 34°F to 65°F.
Normal Sounds Your new wine and beverage cooler may make sounds that are not familiar to you. Most of the new sounds are normal. Hard surfaces like the floor and walls can make the sounds seem louder than they actually are. The following describes the kinds of sounds that might be new to you and what may be making them. Rattling noises may come from the flow of the refrigerant. Items stored on top of the wine and beverage cooler can also make noises.
CLEANING AND MAINTENANCE Periodic cleaning and proper maintenance will ensure efficiency, top performance and long life. Exterior Cleaning The door and cabinet may be cleaned with a mild detergent and lukewarm water solution such as 2 tablespoons of baking soda to 1 quart of water. Do not use solvent based or abrasive cleaners. Use a soft sponge and rinse with clean water. Wipe with a soft clean towel to prevent water spotting.
Troubleshooting continued Issue The wine and beverage cooler does not turn on. The wine and beverage cooler will not reach the desired temperature The wine and beverage cooler is making strange noises The body of the wine and beverage cooler is electrified. Frost is forming in the wine cooler. Possible cause Solution There is a power failure. Ensure the cooler is plugged in and the power outlet has power. The cooler is not plugged in.
Specifications Description of product Built-in Wine and Beverage Cooler Model CWB7016DZ Voltage/Frequency AC 115V~60Hz Amperage 1.75A Input Power 110W Color Black Cabinet; Stainless Steel Door Storage Capacity 16 wine bottles*, 70 standard 12oz. cans Refrigerant R134a, 3.3 oz. Temperature Range 34 - 65ºF Dimensions (Height x Width x Depth ) 34” x 23 1/2” x 24 1/2”** Weight 103 pounds Note: Technical data and performance information is provided for reference only.
Limited Warranty: Full One-Year Parts and Labor This product is warranted by EdgeStar and is subject to any conditions set forth as follows: WHAT IS COVERED: For a period of ONE (1) YEAR from the date of original retail purchase, EdgeStar will repair or replace any part free of charge including labor that fails due to a defect in materials or workmanship.
EdgeStar Products 500 N. Capital of TX Hwy, Bldg 5 Austin, TX 78746 Toll Free: 1-866-319-5473 Web: http://www.edgestar.com E-mail: service@edgestar.com Register your product, download owner’s manuals, access additional troubleshooting resources, and obtain more information on other great EdgeStar products on the web at: http://www.edgestar.com Product contents and specifications may change without notice. Copyright © 2013 Living Direct, Inc. All rights reserved.